Safeguard Supply ERA-DSRXPG Manuale utente

.Remove the four screws on the bac of the sensor/transmitter case using a Phillips head screwdriver (figure )..Remove top half of case from lower case..nstall a  alaline battery  place it in the holder (figure )..See section titled, "Pairing ranitter to eceier 5.ote hen battery gets wea, it will cause paired one to flash LED on receiver for  minutes when triggered.•The ERA-DSTX must be programmed to a ERA receiver to function.Programming instructions, settings,  mounting instructions are included in this manual.•onsult the receivers user manual for more details  specifications for settings.•The ERA-DSTX is powered by a  alaline battery (not included).•p to  ERA-DSTXs may be programmed to a ERA receiver, Theres no limit to the number of receivers programmed to the ERA-DSTX.•ts recommended to choose a different melody for each programmed receiver so you can determine which transmitter triggered the receiver.•hen the transmitter battery is low, it cause the receiver to generate the sound twice in a row.•Pacage contents PR sensortransmitter, plate mount, swivel mount, screws (), plugin receiver,  this user guide.Pair ranitter to eceier(Always test unit prior to installation)

The transmitter wors with the included receiver, the ERA-RXPG, as well as the ERA-DRX  ERA-PRX receivers. Basic programming calls for the user to pair the transmitters with a receiver  select a melody for the transmitter to instruct the receiver to play when triggered.                          (igure )Setu Ste or Setting  Senorranitter.nstall a  battery (not included). See the section titled "Battery nstallation." ote do not re-assmeble the case until programming is complete..Pair the sensortransmitter to the receiver. See section titled Pair ranitter to eceierOnce you have

.ote some settings of the transmitter may be adusted as needed. Please see section titled ance Senor Setting•Dimensions (HD) .5    .5 inches•Operating temperature - to   (-. to . )•Operating freuency  HRA-DSRXPG Alarm KitOwner’s Manual

                                          Introduction

The ERA-DSTX is an outdoor rated PR sensor compatible with all ERA receivers. hen the combination of heat  motion are detected, the sensor will transmit a wireless radio signal up to , ft. to the receiver . This user manual is for the ERA-DSRXPG which includes one outdoor driveway sensor  one plugin receiver.elul oteERA-DSTX Sensor Specifications:

•Power source: 9V alkaline battery

•Detection range low, to 5 ft., medium, to 5 ft., high, to  ft.•ireless range up to , ft.(igure )(igure )Battery Installation:

(igure 5)1. Plugin the receiver (figure 5) into a standard wall outlet.2. Hold down the "mode" button on the receiver until you hear a short tone sound. A red LED will appear in the strobe lens of the receiver. This denotes programming mode. 3. By default, the receiver is set to play the "ding-dong" sound. To change the melody, press the "volume" button to scroll through the available sounds. Once you hear the melody want, stop pressing the button.4. Next wave your hand over the "sensor cell" or press the "test" button on

the transmitter/sensor (see figure 4).

5. You should hear a quick chime sound denoting successful pairing of the

sensor to the receiver. If this is the only sensor/transmitter you are

programming, go to the next step. To pair an additional transmitter,

repeat steps 3 & 4.

6. To exit programming mode, hold down the "mode" button (figure 5)

until you hear a short tone sound (approximately 3 seconds).

Mounting te ranitterNote:                                   •ocationoTry to mount on a wooden post, fence or tree. Avoid mounting on metal if possible.oTry to mount in a location free of obstacles such as metal siding, trees that may cause transmission interfence.oThe product has a very long range, but these obstacles will interfere in the effective range.oTry to place unit - ft. off the ground  approimately  ft. from either side of driveway or path you are monitoring.oThe sensor will detect people  vehicles up to approimately  ft. away (on high setting),  sometimes even farther. orthis reason, avoid pointing the transmittersensor at roads in the distance.oae sure unit is mounted so that it does not move during wind or storms. This could generate false triggers.TECHNICAL SUPPORT

f you encounter any difficulty in the operation of this product after reading the manual, please contact us. ou can reach us by phone at -5- from  A to 5 P onday through riday (Eastern Standard Time). e will be happy to answer your uestions and help you in any way we can.WARRANTY

Safeguard Supply warrants this product to be free of defects in material and wormanship for a period of one year from the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of god or improper operation. f this product does become defective, simply return it to Safeguard Supply. Please include a note describing the troubles along with your name and return address as well as the original sales receipt. f the product is covered under warranty it will be repaired or replaced at no charge. f it is not covered by warranty, you will be notified of any charges before wor is done.Safeguard Supply oon Station t.   ennesaw, GA www.safeguardsupply.comance Senorranitter SettingNote: •Remove the battery. Prior to adusting any sensor settings, please remove the battery. Remove bac cover and disconnect the battery. See "Batter ntallation•Remove  adust umper. umpers are small blac plastic pieces that fit over pins on the circuit board. (figure 5).(igure 5)•Gently slide the umper off the pins for the settings you would lie to change. f you cannot use your fingers, you can use tweeers. •Slide the umper bac onto the pair of umper pins that correspond with the setting you want to change (see images below).•ange hanges the distance that the motion detector will detect motion (sie of monitored one). • Turn LED onoff (LED triggered when unit is transmitting radio signal).•ilter hanges the sensitivity level of the motion detector. Recommended O for indoor use, O for outdoor use).•eet hanged minimum time between alarm activations.•Select a Mounting BracketoPlate mount is ideal for outdoor locations (trees, posts, fence).See figure .oSwivel mount is ideal for indoor locations (figure ).•Select a Mounting BracketoEnsure arrow on bracet is facing up.oSlide transmitter down on bracet. LED on transmitter should be towards the top of the case to function correctly.(figure ).(igure )(Figure 6)

Altri manuali Safeguard Supply Sistema di sicurezza