Samsung DW60A6092 Series Istruzioni per il montaggio
DISHWASHER
REPAIR Guide
DISHWASHER
BASIC MODEL : DW60A6092 Series
DW60A6090 Series
MODEL NAME : DW60CG530 Series
DW60CG550 Series
DW60CG552 Series
MODEL CODE : DW60CG530B00 DW60CG550B00
DW60CG552B00 DW60CG550I00
DW60CG550FSR DW60CG552FSR
DW60CG550FWQ DW60CG550SSR
DW60CG552SSR DW60CG550USR
DW60CG552USR
* For End User.
DW60CG5**F* DW60CG5**U**
DW60CG5**S** DW60CG5**B**
DW60CG5**I**
IMPORTANT SAFETY NOTICE
Following the repair by a non-authorized service provider self-repair or non-professional
repair of the product Samsung is not liable for any damage to the product any injury or
any other product safety issue caused by any attempt to repair the product which does
not carefully follow these repair and maintenance instructions. Any damage to the
product caused by an attempt to repair the product by any person other than a
Samsung certified service provider will not be covered by the warranty.
All rights reserved.
This service guide may not be reproduced in whole or
as a part in any form whatsoever without the written permission of
the SAMSUNG ELECTRONICS Company.
WARNING
Note
1. You can check where to buy replacement parts at http://www.samsung.com/support/
2. Visit the part purchase site and enter the model code of your product to check the parts available for pur-
chase. The model code is labelled on the edge of the tub. When you open the dishwasher’s door, you can
check the model code and version on the barcode label at the left side of the tub.
3. For replacement parts make sure the part name matches that of the illustration in this manual.
- User-serviceable parts are limited to door hinge and seals other seals spray arms drain lters interior
racks and plastic peripherals such as baskets and lids.
Caution
1. The part name listed on the site may differ from that in this manual. Please make sure you choose the right
part name.
2. Be sure to wear safety gloves while making repairs.
3. Due to the heavyweight it is recommended for 2 or more people to handle the product.
Tools For Removal And Reassembly _ 3
1. TOOLS FOR REMOVAL AND REASSEMBLY
Tool image
No. Tool Type Remarks
①Adjustable Wrench
②Open-end Wrench 1-7/16”
③Vice Pliers
④Others
(screwdriver, nipper, long nose pliers) Common tools for servicing
Screwdriver – Phillip, Flat, Torx T15
⑤Ear clamping tool In reassembling of the clamp-bend(ear clamp) using our
SVC part, this tool is needed.
NOTE :
Preparation for parts replacement
1. Remove the residual water inside the product. (Drain the water by operating the drain pump)
2. Close the water supply valve.
3. Turn off the power & disconnect the power cable.
You must turn off the circuit breaker connected to the product.
4. Pull out the unit from the sink and lay it on the oor.
Be careful of the drain hose when pulling out the unit.
5. For materials and repair information related to self-repair, refer to the web site: www.samsung.com/support
4 _ Standard Disassembly Drawings
2. STANDARD DISASSEMBLY DRAWINGS
2-1. PRECAUTION
Caution
Before servicing,
- Make sure to remove all items include baskets inside dishwasher.
- Drain the water in the dishwasher and disconnect the power supply.
- Lock the water faucet that is connected with inlet hose.
- Uninstall the dishwasher from the furniture cabinet except simple work.
- Disconnect the Inlet & Drain hoses from the duct, if the hoses are too short to pull the dishwasher out of the furniture
cabinet enough.
- Make sure to remove any remaining water in the Sump and hoses by rag or vacuum.
→ There is a risk of water spill on the oor.
Disassembly and Reassembly _ 5
2-2. CAP CASE BRAKE / GASKET BRAKE
- Cap Case Brake : DD81-02725A / SVC-CAP CASE BRAKE
- Gasket Brake : DD81-02726A / SVC-GASKET-BRAKE
Part Figure Description
CAP CASE
BRAKE /
GASKET
BRAKE
A
B
[DISASSEMBLY]
1. Remove 3 screws that connect left SIDE PANEL to
front side of dishwasher.
- Type A: DD81-02693A / 2 pcs
- Type B: DD81-02694A / 1 pc
Warning
Be sure to remove the power plug before servicing.
NOTE :
In case of Free Standing models, there’re no
screws of type B.
C
B
2
1
2. Remove 3 screws at the back side of dishwasher.
- Type C: DD81-02692A / 1 pc
- Type B: DD81-02694A / 2 pcs
NOTE :
In case of Free Standing models, take off the
COVER TOP by removing 2 screws of typeA. After
removing screws, pull the COVER TOP backward
rst, and take it off upward.
Guide Tub Top
3. Remove 1 screw at the left side of GUIDE TUB
TOP.
- Screw: DD81-02694A / 1 pc
6 _ Disassembly and Reassembly
Part Figure Description
CAP CASE
BRAKE /
GASKET
BRAKE
4. Take off the left SIDE PANEL.
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges.
5. Take off the CAP CASE BRAKE by rotating to
counter-clockwise direction with long-nose pliers.
Caution
It can brake easily when you use the iron part of the
pliers. Remove the cap using the handle part of the
pliers to prevent damage.
Cap Case brake Gasket brake
6. Remove the GASKET BRAKE from the CASE
BRAKE assembly.
[ASSEMBLY]
1. Fit the GASKET BRAKE on the CASE BRAKE,
and fasten the CAP CASE BRAKE by rotating to
clockwise direction with long-nose pliers.
Caution
It can brake easily when you use the iron part of
the pliers. Remove the cap using the handle of the
pliers to prevent damage.
Caution
Pay attention to assemble the seal correctly.
It may cause the water leakage when it’s
misassembled.
2. Assemble the left SIDE PANEL with the screws.
Caution
Fasten the screws that was assembled to origin
location. Don’t assemble to other locations.
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges.
Disassembly and Reassembly _ 7
2-3. DOOR HINGE
- Door Hinge : DD82-01675A, DD82-01676A / SVC ASSY-HINGE-RIGHT, SVC ASSY-HINGE-LEFT (except DW60CG5**I**)
Part Figure Description
DOOR HINGE
(except
DW60CG5**I**)
BA
[DISASSEMBLY]
* PREPARATION: Remove the SIDE PANEL Left &
Right refer to the section of ‘CAP CASE BRAKE /
GASKET BRAKE’.
1. Remove the 8 screws xing the ASSY CONTROL
PANEL with a Torx® T15 screwdriver.
- Type A: DD81-02756A / 2 pcs
- Type B: DD81-02758A / 6 pcs
Warning
Be sure to remove the power plug before servicing.
Caution
The screws can fall into the SUMP after disassembly
.
Keep the screws away in a safe place to
reassemble the DOOR.
DW60CG5**F** / DW60CG5**U** /
DW60CG5**S**
DW60CG5**B** / DW60CG5**I**
2. Remove the wire connector of the Sub PBA.
C
3. Remove the 6 screws xing the DOOR OUTER with
a Torx® T15 screwdriver.
- Type C: DD81-02757A / 6 pcs
Warning
Be sure to remove the power plug before servicing.
Caution
Be careful to avoid injury when the DOOR is closed
after removing DOOR OUTER
.
Caution
The screws can fall into the SUMP after disassembly.
Keep the screws away in a safe place to reassemble
the DOOR.
8 _ Disassembly and Reassembly
Part Figure Description
DOOR HINGE
(except
DW60CG5**I**)
Hook Hook
4. Remove 2 terminals that connected to
DETERGENT DISPENSER, and 1 ground wire that
connected to BRACKET DOOR FRAME.
Warning
Be sure to remove the power plug before servicing.
Caution
Pay attention to hook of terminals.
5. Remove HOLDER ROPE DOOR from the DOOR
HINGE left & right with the DOOR closed.
Caution
Pay attention to DOOR drop after removing the
rope. It may cause injury.
GUIDE HINGE 6. Push both ribs of GUIDE HINGE to pull out the DOOR.
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges of broken parts.
Disassembly and Reassembly _ 9
Part Figure Description
DOOR HINGE
(except
DW60CG5**I**)
About 15˚
DOOR INNER assembly
7. Do same work at the opposite side, and pull out the
DOOR INNER assembly to the direction of about 15˚.
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges.
8. Remove the 2 screws to remove the BRACKET
DOOR FRAME from the DOOR INNER.
- Screws: DD81-02728A / 2 pcs
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges.
9. Remove the 2 screws at each side to remove the
DOOR HINGE from the DOOR INNER.
- Screws: DD81-02764A / 4 pcs
ASSY
HOUSING
SUPPORT
10. Remove the GUIDE HINGE from the DOOR
HINGE.
NOTE :
DOOR HINGE and GUIDE HINGE will serviced to
assembly only.
NOTE :
In case of Free standing models(DW60A60**F*),
it need to disassemble ASSY HOUSING
SUPPORT(DD82-01727A) also.
10 _ Disassembly and Reassembly
Part Figure Description
DOOR HINGE
(except
DW60CG5**I**)
[ASSEMBLY]
1. Assemble the DOOR HINGE assembly and
BRACKET DOOR FRAME with machine screws.
- Screws for DOOR HINGE assembly:
DD81-02764A / 4 pcs
- Screws for BRACKET DOOR FRAME:
DD81-02728A / 2 pcs
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges.
About 15˚
2. Fit the DOOR INNER assembly into the holder of
TUB to lock the hook of DOOR HINGE.
Warning
Do not do this work without safety gloves. It may
cause injury from sharp edges.
3. Fit the HOLDER ROPE DOOR on the both side of
the DOOR HINGE with the DOOR closed.
4. Connect the 2 terminals of DETERGENT
DISPENSER, and 1 ground wire.
Caution
Make sure the Wire harness is not getting stuck in
other parts.
Questo manuale è adatto per i seguenti modelli
20
Indice
Altri manuali Samsung Lavastoviglie
Samsung
Samsung DMT350 Series Manuale utente
Samsung
Samsung DW6 R707 Series Manuale utente
Samsung
Samsung DMT SERIES Manuale utente
Samsung
Samsung DW80K5050U Manuale utente
Samsung
Samsung DW60J9950 Series Manuale utente
Samsung
Samsung DW80M2020US/AC Manuale utente
Samsung
Samsung DW80K7050 Series Manuale utente
Samsung
Samsung DW80F600UTB/AA Manuale utente
Samsung
Samsung DW5 R405 BB Series Manuale utente
Samsung
Samsung DMR78AHB Guida utente
Samsung
Samsung DMR77 series Manuale utente
Samsung
Samsung DMT4000 series Manuale utente
Samsung
Samsung DW80M2020US Manuale utente
Samsung
Samsung DW80H997 Series Manuale utente
Samsung
Samsung DW60J9970 Series Manuale utente
Samsung
Samsung DW6 M605 Series Manuale utente
Samsung
Samsung DW5363 Series Manuale utente
Samsung
Samsung DW60M9970 Series Manuale utente
Samsung
Samsung DW80F600 Series Manuale utente
Samsung
Samsung DMT800 Series Manuale utente
