Samsung JE68-00131B Manuale utente

JE68-00131B

Rev. 1.02

http://www.samsungminiprinters.com

SRP - 770

Thermal Label Printer

erator’s Manual

Safety Precautions

In using the present appliance, please keep the following safety

regulations in order to prevent any hazard or material damage.

Violating following instructions can cause serious injury or death.

Do not plug several products in one

multi-outlet.

This can provoke over-heating and a fire.

If the plug is wet or dirty, dry or wipe it

before usage.

If the plug does not fit perfectly with the

outlet, do not plug in.

Be sure to use only standardized

multi-outlets.

You must use only the supplied adapter.

It is dangerous to use other adapters.

Do not pull the cable to unplug.

This can damage the cable, which is the

origin of a fire or a breakdown of the printer.

Keep the plastic bag out of children’s reach.

If not, a child may put the bag on his head.

Do not plug in or unplug with your hands

wet.

You can be electrocuted.

Do not bend the cable by force or leave it

under any heavy object.

A damaged cable can cause a fire.

If you observe a strange smoke, odor or

noise from the printer, unplug it before

taking following measures.

Switch off the printer and unplug the set

from the mains.

After the disappearance of the smoke, call

your dealer to repair it.

WARNING

PROHIBITE

PROHIBITE PROHIBITE

ONLY SUPPLIED ADAPTER

PROHIBITE

TO UNPLUG

PRINTER

Violating following instructions can cause slight wound or damage the appliance.

Keep the desiccant out of children’s

reach.

If not, they may eat it.

Install the printer on the stable surface.

If the printer falls down, it can be broken

and you can hurt yourself.

Use only approved accessories and do

not try to disassemble, repair or remodel

it for yourself.

Call your dealer when you need these

services.

Do not use the printer when it is out of

order. This can cause a fire or an

electrocution.

Switch off and unplug the printer before

calling your dealer.

Do not let water or other foreign objects

in the printer.

If this happened, switch off and unplug the

printer before calling your dealer.

WARNING

PROHIBITE PROHIBITE

PRINTER

PRINER

DISASSEMBLING

PROHIBITED

PRINTER

PROHIBITE

PRINTER

DEALER

TO UNPLUG

Table of Contents

1. Unpacking & Repacking......................................................................... 5

2. Samsung Label Printer ................................................................... 6

3. Connecting the Power Supply...................................................... 7

4. Connecting the Interface Cable .................................................. 8

5. Installing or Replacing the Paper Roll......................................9

6. Setting the Dip Switches .............................................................10

7. The Self Test.....................................................................................11

8. The Peel-off ......................................................................................12

9. Using Fan Fold Paper.....................................................................13

10. Driver Install Guide.....................................................................14

I. To install SRP-770 windows driver

II. To use USB interface

III. Tip & Trouble shooting

1. Unpacking & Repacking

Your printer box should include these items. If any items are damaged or missing,

please contact your dealer for assistance.

Note : Please keep the packing materials(①,②,④,⑥) for future repacking to send

a printer for repairs.

⑧Operator’s Manual & CD

⑨Label

(Paper)

⑦Power Cord

⑤Printer (SRP-770)

③Power Supply

④Pe-bag

①Printer Box

②Cushion

(

Bottom

)

⑥Cushion

(

)

※You can repack the printer package in above numeric order(①~⑨)

2. Samsung Label Printer

Feed Button

Cover Peel-off

Status Indicator

Cover Open/Close

Power Switch

Printer Head

Paper Holder

Paper Guide

Peel-off Sensor

Paper(gap) Sensor Paper Adjuster

Power Connector

Interface Connectors

(RS-232C, IEEE1284, USB)

Dip Switch

3. Connecting the Power Supply

CAUTIONS:

When connecting or disconnecting the power supply from the printer, make sure that

the power supply is not plugged into an electrical outlet. And the power supply’s

rated voltage and your outlet’s voltage do not match, contact your dealer for

assistance. Then do not plug in the power cord. Otherwise, you may damage the

power supply or the printer.

1. Make sure that the printer’s power switch is turned off, and the power supply’s

power cord is unplugged from the electrical outlet.

2. Check the label on the power supply to make sure that the voltage required by the

power supply matches that of your electrical outlet.

3. Plug in the power supply’s cable as shown below. Notice that the flat side of the

plug faces down.

4. Connecting the Interface Cable

Universal Serial Bus

(USB) Serial Interface

RS-232 default

setting is 19200 baud,

no parity, 8 data bits

and 1 stop bit

Parallel Interface

Installing or Replacing the Paper Roll

①Open Cover ②Open Guides

③Install Roll

⑤Close Cover

④Close Guides to the Width of the paper

6. Setting The Dip Switches

6-1. Setting the Dip Switches

The Dip Switches are located on the bottom of the printer. The Dip Switches are used to

set the Printer to perform various functions. Follow these steps when changing Dip

Switches setting :

1. Turn the printer power switch off.

2. Remove the screw on the bottom of the printer and open the bracket.

3. Flip the Dip Switches using tweezers or another narrow-ended tool. Switches are

off when up and on when down in the Figure below.

4. The new setting takes effect when you turn on the printer.

Note : Always change Dip Switch settings only when the printer is turned off.

6-2. Functions of Dip Switches

6-2-1. Dip S/W 1 6-2-2. Dip S/W 2

NO Functions Details

2 1 Speed

Off Off 2.5 ips

Off On 3.0 ips

On Off 4.0 ips

1,2 Speed

Selection

On On 5.0 ips

4 3 Density

Off Off 0(Low)

Off On 7

On Off 13

3,4 Density

Selection

On On 20(High)

5,6,

Developer

Mode Default --- off

Off Move to Cutting Position

8 Position

Selection On Move to top of next page

No Functions Details

21 Baud Rate

Off Off 9,600 bps

Off On 19,200 bps

On Off 57,600 bps

1,2 Baud

Rate

On On 115,200 bps

3 Reserved

4 Reserved

5~8 Developer

Mode Default --- off

. The Self Test

The self-test checks whether the printer has any problems. (You cannot perform this

procedure if using the printer’s label peel-off option) If the printer does not function

properly, contact your dealer. The self-test checks the following;

1. Make sure that paper roll has been installed properly.

2. Turn on the power while holding(2sec) down the FEED button. The self-test begins.

3. The self-test prints the current printer status, which provides the control ROM version

and the DIP switch setting.

Cleaning Head※

Paper dust on the heating elements may lower the printer quality. In this case, clean the

print head as follows :

Cautions 1. Turn Off the printer power before cleaning.

2. Note that the thermal head becomes very hot during normal operation,

creating the danger of burn injury. Be sure to wait for about 10 minutes

after turning printer power off before beginning the cleaning.

1. Open the printer cover.

2. Clean the thermal element (the area which is marked a thin black line) of the

thermal head with a cotton swab moistened with a alcohol solvent (ethanol,

methanol, or IPA).

3. After confirming that the alcohol solvent has been dried up completely,

close the cover-open.

Note 1. Never touch the thermal element with your hand,

thenthe thermalelement canbedamaged.

2.Don’tscratch theprinterhead.

8. The Peel-off

Printers can Peel-off a single label.

You must remove the label before the printer prints the next label.

Open the peel①-off cover and turn on peeler switch.

Remove the one a paper and Adjust the paper guides and close the cover.②③

insert the paper through slot.

remove

9. Using Fan Fold Paper

Insert paper through both the rear slot and guides.

Adjust holders and guides to the width of the paper.

Open the Dust Cover

and Insert paper

Dust Cover

Adjust holders papers and paper Fixed Adjust Guides

Paper Fixed

10. Driver Install Guide

I. To install SRP770 windows driver

1. Insert CD-ROM included in your printer package then install guide program will appear

automatically. Please click on Windows Drivers.

2. You can see the driver auto-install program prepares to install driver matching your

windows system.

3. If it is first time to install SRP770 windows driver, you can see the Welcome message as

below. Please click on Next> to continue install procedure.

** If previous version driver is already installed in your system, some other type

window will appear. In this case, please refer to “ . Tip & Trouble shooting”Ⅲ

4. If you accept the license agreement, click on Yes to continue install procedure.

5. If you want to use USB interface with SRP770 printer, please select both “SAMSUNG

SRP770” and “SAMSUNG USB Port Monitor” together and click on Next>.

6. Just wait until auto-installer program finishes drivers setup.

7. Click on Finish to exit auto-installer program.

8. You can see the SAMSUNG SRP770 driver is correctly installed in Printer folder.

II. To use USB interface

Microsoft windows basically supports Serial and Parallel interface without installing any port

drivers but in case of USB interface, USB port driver should be pre-installed. Please follow

next steps to properly install Samsung USB port driver in your system.

1st. Turn off the printer power switch and don’t turn on while auto-install program setup

drivers in your system.

2nd . Execute auto-install program as shown in “ .To install SRP770 windows driver”Ⅰ

or manually.

3rd. During installation procedure, please select both SAMSUNG SRP770 and SAMSUNG USB

Port Monitor together as below.

4th. After driver installation is finished, Please connect USB cable between your system and

printer correctly and turn on the printer power switch.

5th - 1.

In Windows XP or 2000,

1) When you turn on the printer power switch first time after installing USB port driver, the

OS recognize the printer and pop up the window to complete USB driver installation a.

Please click on Next>.

2) Just wait…

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Samsung Etichettatrice

Samsung

Samsung SRP-350U Manuale utente

Manuali Etichettatrice popolari di altre marche

Brother

Brother P-Touch 2420PC Manuale utente

newell

newell Dymo LabelManager 210D Manuale utente

Brother

Brother TD-4000 Manuale utente

U-Line

U-Line BROTHER H-8754 Manuale utente

Tharo Systems

Tharo Systems H-435+ Manuale utente

Brother

Brother E300 Manuale utente

Godex

Godex RT700 SERIES Manuale utente

ID Technology

ID Technology 252 Manuale utente

Labelmate

Labelmate MC-11 Manuale utente

CAB

CAB XD4M/300 Manuale utente

Avery Dennison

Avery Dennison Pathfinder 6057 Manuale di servizio

Brother

Brother P-touch PT-9700PC Manuale utente

TSC

TSC PEX1000 Series Manuale utente

Adkins

Adkins Label Master Manuale utente

Epson

Epson LabelWorks LW-400 Manuale utente

Primera

Primera 510212 Manuale utente

Brady

Brady BradyPrinter S3100 Manuale utente

DuraLabel

DuraLabel LabPRO Manuale utente