Samsung AC-505CM Series Manuale

LED R&D Lab(VD)

LED Display Install Manual

IAC Series

LH015IAC***

Ver. 0.3

LED R&D Lab(VD)

Revision History

Version Date (Y/M/D) Description

0.1 2023/06/01 Release ver 0.1

0.2 2023/06/12 Modification Side by Side Content (P114~118)

Delete Side by Side Screen Split scenario #2 (P119)

0.3 2023/06/15 Add checking CABINET number (BNV20231FE9) (P18,20)

LED R&D Lab(VD)

1. Product and installation information

2. Preparation of Cabinet installation

3. Wall Mount

4. Frame installation and cable connection

5. Frame Bezel Installation

6. Dehumidification mode guide

7. IP Manual setting Guide

※ Appendix1 -LED MODULE and CIRCUIT replacement method

※ Appendix2 –System Main / TCON / LED Module Update data on replacement

※ Appendix3 –Side by Side installation

※ Appendix4 –LSM connection

※ Appendix5 –Gradation Calibration (SSA)

※ Appendix6 –Framelock mode support timing table

Table of contents

LED R&D Lab(VD)

MODEL Product appearance and information

IAC series

REMARK IAC Series : Package Type / 60 Hz Refresh Rate

◆Model specification

-This manual is an installation manual for IAC and can be applied to the model below.

1. Product and installation information

LED R&D Lab(VD)

◆Model specification (IAC)

Specifications

130”

P1.5

CABINET

Size

(mm)

Horizontal 2888.55

vertical 1628.55

Resolution

(Pixels)

Horizontal 1920

vertical 1080

Module (EA) 27 X 4 (108)

weight (kg)

(Cabinet) 16.0

SET weight (kg) 124.55

Packing weight (kg) 78.9

Power consumption (W) Typical 685W (Max 1660W)

Luminance (nit)

Max 500

Peak 1000

1. Product and installation information

LED R&D Lab(VD)

◆Cabinet product information

1628.55

62.2

130”

2888.55

1. Product and installation information

LED R&D Lab(VD)

◆Installation precautions (LED damage)

precautions Image

[External impact, fall caution]

1 Remove the cover-corner of the product before installation and do not

impact the LED surface or drop it on the floor.

2 Do not place the product on the vibrator and do not place the LED

surface facing the floor.

3 Make sure that the edge of the LED module is not damaged by external

contact.

4 Do not load more than 12 steps.

① ②

③ ④

[Watch out for LED damage caused by static electricity]

▶Do not work by touching the LED surface with hands without gloves.

[Caution of LED damage caused by metal]

▶Be careful not to get metal on the front of the LED.

▶When attaching the metal, separate the module and remove it using a

magnet.

MODULE

Front

metal

1. Product and installation information

LED R&D Lab(VD)

precautions Image

[Caution of LED damage caused by liquid]

When water or various chemicals touch the LED, the inside of the LED may be damaged.

①Water, dew, air conditioner condensate, sprayer, sweat, and saliva do not directly touch the

product.

-Be careful not to sweat on the product. (※ Maintain proper temperature so as not to sweat)

-Be careful not to spit on the product, and it is recommended to wear a mask.

②The following substances should not be directly in contact with the product, and

the case of exposure of the steam to the product should be minimized.

-Detergent or disinfectant : carpet cleaning detergent, glass cleaner, 84 disinfectant, etc.

(※ When cleaning the floor or wall with detergent or water, it is recommended to install a screen so that it does not touch the

product)

-Various chemicals: paints, mosquito repellents, cinnabar, benzene, toluene, solvents, surfactants, halogens (chlorine, bromine),

and substances containing these ingredients;

③If liquid touches the product

-If there is water on the product, turn off the product immediately, dry it enough for more than a day, and run the

dehumidification mode to remove moisture from the LED. (※ P74, refer to "Dehumidification mode using LSM")

-If there is any liquid other than water on it, remove it with alcohol and run the dehumidification mode.

[Precautions related to construction]

①In the case of installation at the construction site, the product must be installed after construction and

cleaning are completed.

②If the product is under construction in the installed space, take the following measures.

-Shielding film should be installed to protect the product by sealing the entire product so that it is not exposed to dust and

various liquids.

-Operates a video or 100 gray scale white for more than 2 hours every day.

-After the construction is completed, remove enough dust, various liquids, and steam, remove the shield, and execute the

dehumidification mode.

카펫

클리너 유리

세정제

Taping Shielding film

Disinfectant

※ Only use for IWA

◆Installation precautions (LED damage)

1. Product and installation information

LED R&D Lab(VD)

◆Heat dissipation guide

Installation condition

-Conditions for using SAMSUNG WALL MOUNT

-Solar direct sunlight conditions cannot be installed (including glass window passage conditions)

-It is recommended to use room temperature below 25°C

-Effect of Cold/Hot Air Conditioning System

-When cold / hot air is the same air conditioning system,

∙Be careful not to let the warm air touch the product.

-Outside temperature measurement position

Measured at a distance of 300mm from the center of the product

Air vent aperture ratio

-use mesh type air vent

-If the aperture ratio is not 100%, the separation distance =

Minimum distance

aperture ratio(%) /100

-aperture ratio (%) =    .  ℎ

  

※ It is written based on Full white, back light 7

Video, created based on back light 10

wall

Outside

temperature

measurement

position

300mm

1. Product and installation information

LED R&D Lab(VD)

•Vertical wall installation (if Fan is not applied)

WALL

Air vent area

minimum 30mm

set ~ ceiling

set ~ floor

1. Product and installation information

minimum 30mm

Altri manuali per AC-505CM Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Samsung Monitor

Samsung

Samsung S27E591C Manuale utente

Samsung

Samsung S32A80 Series Manuale utente

Samsung

Samsung 203B - SyncMaster - 20" LCD Monitor Manuale utente

Samsung

Samsung SyncMaster 941MW Manuale utente

Samsung

Samsung SyncMaster 940MG Manuale di installazione e funzionamento

Samsung

Samsung SyncMaster 997MB Plus Manuale utente

Samsung

Samsung 943T - SyncMaster - 19" LCD Monitor Manuale utente

Samsung

Samsung SyncMaster 400TS-3 Manuale di installazione e funzionamento

Samsung

Samsung BX2030N Manuale utente

Samsung

Samsung LHA20WS Manuale utente

Samsung

Samsung 204B - SyncMaster - 20.1" LCD Monitor Guida rapida

Samsung

Samsung OH46D Manuale utente

Samsung

Samsung T240HD - SyncMaster - 24" LCD Monitor Manuale utente

Samsung

Samsung SyncMaster S19A300N Manuale utente

Samsung

Samsung QB43R Manuale utente

Samsung

Samsung 957D Manuale utente

Samsung

Samsung PS-42A5S Manuale utente

Samsung

Samsung SyncMaster P2470HD Manuale utente

Samsung

Samsung SyncMaster 172B Manuale di istruzioni

Samsung

Samsung MP5671 Manuale utente

Samsung

Samsung U32R590 Manuale utente

Samsung

Samsung SyncMaster 2343NW Manuale utente

Samsung

Samsung SAMTRON 76DF Manuale utente

Samsung

Samsung SyncMaster 750DFT Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione