Samsung SyncMaster 460UT Manuale utente
Installation Guide
460UT 460UTN
BN68-01537F.indb 1 2009-12-18 12:17:49
Contents
Safety Precautions 01 Safety Precautions
Introduction 02 Unpacking
02 Attaching the bracket
ͽ
to the monitor
03 Mounting the bracket
;
onto a wall
06 Arranging the monitors
07 Fine tuning
10 Detaching the monitors
Product specifications 11 Product specifications
Product drawings 12 Product drawings
13 Drawings
BN68-01537F.indb 1 2009-12-18 12:17:49
]Warning
Failure to observe the instructions herein can cause serious injury or death.
1. Be sure to contact an installation expert authorized by your dealer to perform the installation.
• Installation by a non-professional may cause personal injury.
If you are planning to relocate or replace the
product after installation, be sure to consult with
an installation expert authorized by your dealer.
After installation, do not apply excessive force
or physical pressure on the product.
2. Do not let your children play in the vicinity of the product.
• They may bump their head or body against the corner of the product and suffer personal injury.
3. Be careful not to let the back of the product hit against the wall when it is rotated or the angle is adjusted.
• You can protect the wall and product from any damage by attaching a piece of sponge to each corner of the product.
4. Do not install the product on a wall that cannot bear the weight of the product.
• The product may fall, and get damaged or cause personal injury.
5. Products installed in unusual, abnormal or extreme areas may be subject to serious performance problems due to
the surrounding environment. Be sure to consult with a Samsung service center before installing the product in
such an area.
• Areas exposed to an excessive amount of fine particles or moisture, chemicals, extreme temperatures, high humidity,
automobiles, etc.
The information contained herein is for your safety and to prevent any loss of
property. Please read the instructions carefully to use the product correctly.
This mandatory sign is used to emphasize the instructions that must be observed.
Safety Precautions
English - 1
BN68-01537F.indb 1 2009-12-18 12:17:49
Unpacking
Monitor-mount bracket ͽWall-mount bracket ;Screw ͽ
(M8 X 60mm) : x4
Screw ;
(M8 X 30mm) : x4 Coupler : x2 Screw holder: x4
Wood screw
(M5 X 50mm) : x8 Safety fastener: x2 Screw Ϳ
(M5 X 10mm) : x2
Attaching the bracket ͽto the monitor
1. Assemble the four screws ͽand the screw holders, and fasten them to fix the bracket ͽto the monitor as
shown in the picture below.
]Warning
Check to confirm that the bracket ͽis fastened to the monitor.
English - 2
BN68-01537F.indb 2 2009-12-18 12:17:51
Mounting the bracket ;onto a wall
1.
Fix the bracket ;tightly against the wall using the wood screws.
1 2
3 4
5 6
78
As shown in the picture above, fasten in order from Ηto Ξ.
N If it is difficult to fasten the screws into the specific holes, fasten the screws in the adjacent holes.
÷Installing the Video Wall
3 4
1 2
NInstalling the Video Wall should be done by two persons or more.
NThe couplers are only used to install a Video Wall in order to leave a gap between the monitors that make up
the Video Wall. Do not use them when installing only one monitor.
]Warning
1. Before you install on the Video
Wall, check the wall strength
considering the total weight of the
monitors and brackets you want
to install.
- Weight of a monitor: 30kg
- Weight of a bracket: 7kg
2. If you intend to install on a Video
Wall that is four layers or more,
take into consideration the air
conditioning system. Consult with
an expert before installation as
heat from the monitors may cause
problems.
]Warning
1. Ensure you check the wall strength, and do
the reinforcing work before installation if the
wall is not sufficiently strong.
2. The provided screws are for wood.
3. Check the wall and use proper screws
according to the material of the wall, such as
marble, steel plate or concrete.
öHow to fasten a screw
Make a hole using a 3X50
drill.
Clean the inside of the
drilled hole.
Fasten the wood screw into
the hole.
öWhen drilling a hole into a wall, make sure
you use a drill bit and drill of the specified
diameter.
Otherwise, there may be safety problems.
English - 3
BN68-01537F.indb 3 2009-12-18 12:17:52
2. Fix the two couplers into the middle and lower parts of the bracket ;respectively.
Fasten the two screws ;into the bracket ;.
3. To align horizontally, attach the bracket Θto the couplers on the bracket Ηusing the screws ;.
(Should be done by two persons or more.)
After fixing tightly, attach the assembly to the wall following step 1.
Fasten the screws tightly so that there is no space between the couplers and the bracket ;.
4. To align vertically, insert the legs of the bracket Ιcompletely to the top of the bracket Ηto assemble the two
brackets.
English - 4
BN68-01537F.indb 4 2009-12-18 12:17:52
3
3
1 1
5. Following steps 2 to 4, fix the bracket to the location Κ.
NIncrease the number of brackets following the steps above.
]Warning
As shown in the pictures, the
bottom of the bracket Ιmust be
inserted fully into the top of the
bracket Η.
English - 5
BN68-01537F.indb 5 2009-12-18 12:17:53
Arranging the monitors
1. Hook the monitor to which the bracket ͽis attached on the poles of the wall-mount bracket ;.
]Warning
Be sure not to put pressure on the panel with your hands when handling the monitor. Otherwise, you may
break the panel.
2. To prevent the monitor from becoming loose, fasten the safety fasteners using the screws Ϳ.
Fasten them on both sides.
]
Warning
Ensure the hooks
are suspended
securely on the
poles.
English - 6
BN68-01537F.indb 6 2009-12-18 12:17:54
]Warning
Since the monitor may fall during installation, ensure you fasten the safety fasteners on both sides.
3. Arrange the monitor on each bracket following steps 1 and 2.
]Warning
Be careful not to catch your finger during installation.
Fine tuning
NAfter arranging the monitors, if they do not seem well-proportioned, adjust them using the fine-tuning screws
on the brackets.
NBe sure not to leave any height differences or gaps between the monitors.
English - 7
BN68-01537F.indb 7 2009-12-18 12:17:56
1. Correcting height difference between the front and back of a monitor.
If you turn the fine-tuning screw clockwise or counterclockwise, the monitor will move forward or backward
respectively.
The fine-tuning screw’s maximum movement range is 10mm.
Moving the monitor forward Moving the monitor backward
2. Correcting height difference between upper and lower monitors.
If you turn the fine-tuning screw on the bottom of the monitor clockwise or counterclockwise, the monitor will
move up or down respectively.
Lowering the monitorRaising the monitor
English - 8
BN68-01537F.indb 8 2009-12-18 12:17:57
Altri manuali per SyncMaster 460UT
3
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Samsung Monitor
Samsung
Samsung T23B550EW Manuale utente
Samsung
Samsung S32A60U Series Manuale utente
Samsung
Samsung DH48D Manuale utente
Samsung
Samsung 460UTN-UD - 46" LCD Video Wall Display Manuale utente
Samsung
Samsung UD22B Manuale utente
Samsung
Samsung 920NW - SyncMaster - 19" LCD Monitor Manuale utente
Samsung
Samsung 205BW - SyncMaster - 20" LCD Monitor Manuale utente
Samsung
Samsung HPT5054 - 50" Plasma TV Manuale utente
Samsung
Samsung 2263DX - SyncMaster - 22" LCD Monitor Manuale utente
Samsung
Samsung 940MW - SyncMaster - 19" LCD Monitor Manuale utente
Samsung
Samsung IAC Series Manuale utente
Samsung
Samsung PL-50P5HD Manuale utente
Samsung
Samsung S19E410HY Manuale utente
Samsung
Samsung 2263DX - SyncMaster - 22" LCD Monitor Manuale utente
Samsung
Samsung SyncMaster S27A850D Manuale utente
Samsung
Samsung 400UXn - SyncMaster - 40" LCD Flat Panel... Manuale utente
Samsung
Samsung SyncMaster 2032MW Manuale utente
Samsung
Samsung 2233SW - Full HD Widescreen LCD Monitor Guida utente
Samsung
Samsung SyncMaster 950p Manuale utente
Samsung
Samsung SyncMaster S22A450UW Manuale utente
