Santos 40A-40A PPM Istruzioni operative

SANTOS : User and maintenance manual

98140 US 3.0 - 05 2007 1 / 20 www.santos.fr

USER AND MAINTENANCE MANUAL

SANTOS SAS:

140-150 AVENUE ROGER SALENGRO

69120 VAULX-EN-VELIN (LYON) - FRANCE

TÉL. 33 (0) 472 37 35 29 - FAX 33 (0) 478 26 58 21 -

TELECOPIE 33 (0) 478 26 58 21

E-Mail :[email protected] www.santos.fr

AUTOMATIC SILENT ESPRESSO COFFEE GRINDER

#40A-40A PPM / #06-06A

IMPORTANT: documents included in this manual to be kept:

•"CE" COMPLIANCE DECLARATION

•WARRANTY CERTIFICATE

Model #40A – 40A PPM Model #06 – 06A

Coffee grinders - Fruit juicers - Mixers - Blenders - Drinks dispensers - Planetary mixers

Cheese graters - Ice crushers - Mincers - Vegetable slicers – Dough mixer

Moulins à café - Presse-fruits - Mixers - Blenders - Distributeurs de boissons - Batteurs

mélangeurs - Pétrin - Râpes à fromage - Broyeurs à glaçons - Hache-viande - Coupe-légumes

MODELES DEPOSES FRANCE ET INTERNATIONAL

INTERNATIONALLY PATENTED MODELS

SANTOS : User and maintenance manual

CONTENTS

“CE” COMPLIANCE DECLARATION........................................................................................3

IMPORTANT SAFEGUARDS ........................................................................................................4

IMPROPER USE .............................................................................................................................4

ELECTRICAL CONNECTION:.......................................................................................................4

USING FOR THE 1st TIME .............................................................................................................5

RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE..........................................5

YOUR ESPRESSO COFFEE GRINDER #40A - 40APPM, #06 – #06A .....................................6

USING THE MACHINE...................................................................................................................6

STARTING UP:................................................................................................................................6

USING: ............................................................................................................................................6

Coffee grinding adjustment: ........................................................................................................7

Adjusting the measured dose of ground coffee: ..........................................................................7

CLEANING:.....................................................................................................................................8

MAINTENANCE..............................................................................................................................8

Spare parts: ..................................................................................................................................8

Replacing the grindstones:...........................................................................................................8

FAULT FINDING............................................................................................................................10

The machine will not start: ........................................................................................................10

The machine stops as a result of motor over-heating: (the motor unit is hot)...........................10

The machine stops as a result of an overload:...........................................................................10

The machine stops a few minutes after starting.........................................................................11

The ground coffee measure is not even.....................................................................................11

The ground coffee jams in the grinder body conduit.................................................................11

The machine runs for a long time without filling the dose measurer........................................11

MACHINE TECHNICAL SPECIFICATIONS ...........................................................................12

110-120V 50/60Hz wiring diagram...............................................................................................13

220-240V 50Hz wiring diagram....................................................................................................14

220-240V 60Hz wiring diagram....................................................................................................15

Figures...........................................................................................................................................17

WARRANTY CERTIFICATE

.....................................................................................................20

APPLIANCE IDENTIFICATION PLATE

................................................................................20

98140 US 3.0 - 05 2007 2 / 20 www.santos.fr

SANTOS : User and maintenance manual

“CE” COMPLIANCE DECLARATION

THE MANUFACTURER:

SANTOS SAS - 140-150, Av. Roger SALENGRO 69120 VAULX-EN-VELIN (LYON)

FRANCE

HEREBY DECLARES THAT THE MACHINE DESIGNATED ON THE IDENTIFICATION

PLATE AFFIXED:

•UNDER THE APPLIANCE,

•ON THE WARRANTY CERTIFICATE ON THE LAST PAGE OF THIS MANUAL,

COMPLIES WITH THE PROVISIONS OF THE "machines" DIRECTIVE AS MODIFIED

(Directive 98/37/CEI)

AND THE NATIONAL LEGISLATION TRANSPOSING IT.

IT ALSO COMPLIES WITH THE PROVISIONS OF THE FOLLOWING EUROPEAN

DIRECTIVES:

No. 73/23 dated 19/02/73 (Low voltage directive)

No. 89/336 (CEM directive)

No. 2002/95/CE (RoHS directive)

No. 2002/96/CE (WEEE directive)

The machine complies with the provisions of the following harmonised European

standards:

EN ISO 12100 -1 and 2 : 2004 - Machine safety devices - General design principles

NF EN 60204-1: 2006 - Machine safety devices - Machine electrical equipment -

General regulations

NF EN 60335-1 : 2003 - Safety of household and similar electrical appliances

SIGNED IN VAULX-EN-VELIN ON: 01/05/2007

SIGNATORY'S TITLE: CHIEF EXECUTIVE OFFICER

SIGNATORY'S NAME: JACQUES FOUQUET

SIGNATURE

98140 US 3.0 - 05 2007 3 / 20 www.santos.fr

SANTOS : User and maintenance manual

IMPORTANT SAFEGUARDS

When using, cleaning or maintaining the machine, always follow these instructions:

Read all instructions

Note: For easier understanding of the sections below, please refer to the diagrams

at the end of the manual

IMPROPER USE

1. Do not use this appliance for grinding anything other than roasted coffee beans.

2. Never operate the appliance with no coffee beans in the bean container.

3. Remove from the coffee beans any foreign bodies which may damage the grinding

wheels (metal staples, stones, etc.).

4. For electrocution risk protection reasons, never plunge the base into water or any

other liquid.

5. Never touch the moving parts.

6. Never operate the appliance with no coffee beans in the bean container.

7. Unplug the appliance before carrying out any work on it: cleaning, maintenance or

repair.

8. The use of spare parts other than certified SANTOS original parts is prohibited.

ELECTRICAL CONNECTION:

•The electric power supply for the machine is available in 3 single-phase voltages:

-110-120 V 50/60 Hz

-220-240 V 50 Hz

-220-240 V 60 Hz

Line protection: the machine should be connected to a standard 2-pole + earth electric

socket. The installation should be fitted with an RCD and a fuse rated at 16A. The

appliance must be earthed (fig. B)

CARE:

•Before connecting the machine, check that the mains electrical voltage is the same

as the voltage for your appliance. Its value is shown:

¾either on the identification plate (16) under the machine.

¾or on the identification plate on the last page of this manual.

•If the power cable (10) is damaged, it should be replaced by a special unit available

from SANTOS or from approved SANTOS dealers.

98140 US 3.0 - 05 2007 4 / 20 www.santos.fr

SANTOS : User and maintenance manual

CARE: Check that the On / Off switch (11) is in the 0 position before connecting the

power cable plug (10) to your mains electric power socket.

USING FOR THE 1st TIME

Carefully clean the parts in contact with the coffee (fig. A).

Take off the lid (1), the bean container (2) and the ground coffee collector (3) and wash

them with a standard dish washing product.

RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE

This equipment is marked with the selective sorting symbol relating to

wastes from electrical and electronic equipment. It signifies that this product

should be taken over by a selective collection system conforming to the

Guideline 2002/96/EC (WEEE) – part Professional Equipment – so that it

can be either recycled or dismantled in order to reduce any impact on the

environment.

For more information, please contact your Retailer or the SANTOS.

For eliminating or recycling components of equipment, please contact a specialized

company or contact SANTOS.

The electronic products not undergoing a selective sorting are potentially dangerous for

the environment.

The damaging materials should be eliminated or recycled according to the regulations in

force.

98140 US 3.0 - 05 2007 5 / 20 www.santos.fr

SANTOS : User and maintenance manual

YOUR ESPRESSO COFFEE GRINDER #40A - 40APPM, #06 –

#06A

•The silent bar espresso coffee grinder #40A, #06-06A is designed for bars, cafés,

hotels and restaurants. It is suitable for all types of espresso coffee machines.

•Grinder #40A / #6A has, in addition, an automatic start/stop device to ensure a

constant level of ground coffee in the distributor.

•

•The machine consists of an aluminium grinder unit and base, a transparent plastic

bean container, a dose measurer and a dose counter.

•The machine can be used to grind roasted coffee and to deliver it via an adjustable

dose measurer.

•The following adjustments can be made:

oAdjustment of the grinding fineness (from coarse to espresso)

oAdjustment of the ground coffee measure (from approximately 5.5g to 9.5g).

USING THE MACHINE

STARTING UP:

Assembly and preparation:

(fig. A)

1. Model #40A Clip the ground coffee collector (3) onto the base (4).

2. Put the dose measurer lid (24) in place.

3. Put the bean container (2) in place on the grinder body adjustment nut (5).

4. Pour the roasted coffee beans into the bean container and put the lid on the bean

container.

5. Open the bean container shutter (6).

USING:

1. Switch the electric current on to the machine by putting the On / Off switch (11) to

the 1 position (the motor will start) (fig. B).

2. The coffee beans are then ground by the grindstones and the ground coffee leaves

the grinder body and goes to fill the dose measurer.

3. Place the filter-holder under the measurer outlet (23) using the filter-holder support

(22) to help.

4. Pull the measurer handle (21) once or twice to deliver one or 2 measure(s) of

ground coffee.

5. Remove the filter-holder and tamp down the coffee with the tamper (20) fixed to the

dose measurer.

Note: A 5-figure counter on the side of the dose measurer counts each measure.

98140 US 3.0 - 05 2007 6 / 20 www.santos.fr

SANTOS : User and maintenance manual

For #40A / #06A models: the motor stops automatically when the dose measurer is full. It

starts again, after a few measures, when the ground coffee level has dropped sufficiently.

Because of this, the machine can be left with the electric power on in position 1 all the

time it is being used.

Coffee grinding adjustment:

Note: Never leave the machine to run with the two grindstones in contact. If the

grindstones make contact this may result in ground coffee getting jammed in the

grinder body and premature wear of the grindstones.

The machine is factory-set so that the "0" mark on the nut graduated plate (5) relates to

the finest grinding without the grindstones touching (fig. C).

1. Hold the adjustment screw (5) with one hand and press the indexing pointer (7)

with the other

2. Tighten the adjustment nut by turning in a clockwise direction (right-handed

thread) one or two notches for finer grinding.

3. Loosen the adjustment nut by turning in an anti-clockwise direction (right-

handed thread) one or two notches for coarser grinding.

4. Release the indexing pointer (7) to retain the grinding adjustment.

5. Draw off a few measures of coffee to check the grinding adjustment.

Depending on the type of coffee used and the fineness of grinding required, the output

may drop considerably. A too fine grinding setting may heat up the coffee and alter its

flavour.

Adjusting the measured dose of ground coffee:

The dose measurer should be cleaned regularly to prevent conglomerated blocks of

coffee on the cross bars from affecting the dose measurer setting.

The machine is factory-set for a measure of approximately 7g.

1. Turn the machine on and allow the dose measurer to fill up.

2. Draw off 4 to 5 measures; the machine should restart.

3. Wait for the machine to stop and then draw off another 5 to 6 measures.

4. Measure the mass (weight) of the measures after that.

5. Tighten the thumb-wheel (8) by turning in a clockwise direction (right-handed

thread) to reduce the quantity of ground coffee per measure (the thumb-wheel

is adjusted in half-turns) (fig. D).

6. Loosen the thumb-wheel (8) by turning in an anti-clockwise direction (right-

handed thread) to increase the quantity of ground coffee per measure.

7. Draw off more than 6 measures for the adjustment to be taken into account.

98140 US 3.0 - 05 2007 7 / 20 www.santos.fr

SANTOS : User and maintenance manual

CLEANING:

IMPORTANT:

•In every case, the machine should be stopped and the machine's power

supply cable (10) unplugged.

•Cleaning with a water spray or pressure spray is not permitted

Clean the dose measurer properly using a brush.

Make sure that the walls of the coffee delivery conduits and the 6 branches of the

cross-bars are always clean.

MAINTENANCE

Before carrying out any work on the machine, it is essential to unplug it from the mains

and to discharge the motor starting capacitor.

IMPORTANT:Use of spare parts other than certified original SANTOS

parts is prohibited

Discharging the capacitor:

•Unscrew the 2 screws located under the machine in the middle of the base plate

(fig. E).

•Pull the electrical components unit (20) out of the base plate.

•Using a screwdriver with an insulated handle, touch the 2 capacitor connections

(15). The sight of an electric arc shows that the capacitor has been discharged.

Spare parts:

This machine requires no specific maintenance. The bearings are lubricated for life.

If work is required to replace worn parts such as the grindstones or the electric or other

components, refer to the parts list (see exploded view at the end of the manual).

For all spare part orders (see references in the exploded view at the end of the manual),

state:

¾the type,

¾the machine serial number and

¾the electrical specifications (16)

recorded under the machine.

Replacing the grindstones:

IMPORTANT: always change both 2 grindstones (9) at the same

time. (use SANTOS reference 00001B)

98140 US 3.0 - 05 2007 8 / 20 www.santos.fr

SANTOS : User and maintenance manual

The 2 grindstones are identical and can be fitted equally either on the moving plate (18)

(moving grindstone) or on the adjusting "nut" (5) (fixed grindstone) (fig. F).

1. Close the bean shutter (6) (fig. G) .

2. Run the machine until the coffee beans waiting in the grinder body have gone

through.

3. Stop the machine and unplug the mains power lead (10).

4. Take off the bean container (2).

5. With one hand, press on the indexing pointer (7) and with the other unscrew the

adjustment nut by turning it in an anti-clockwise direction (fig. H).

CARE:When this part is fully unscrewed, handle it with care so as not to damage

the brass thread.

6. Unscrew the 3 screws on each grindstone (fig. I). For the moving grindstone, place a

screwdriver across the grinder body and the coffee outlet conduit to stop the

grindstone-carrier plate from turning on unscrewing or screwing up the grindstone

retaining screws.

7. Carefully clean the whole grinder body, in particular the grindstone facing areas.

8. Place each grindstone on its support making sure that there is no coffee dust

between the grindstone and its support.

CARE:The slightest small coffee particle under the grindstone may prevent the

machine from operating correctly. It is recommended that the grinder body is cleaned

with a compressed air jet or a dry brush.

CARE:do not unscrew the grindstone-carrier plate (18) retaining spindle (17) so as

not to upset the assembly geometry (fig. J).

9. Once the 2 grindstones have been replaced, with one hand press the indexing

pointer (7) and with the other place the "ground coffee adjustment nut" (5) on the

grinder body taking care not to damage the thread. Without using force, put the "nut"

(5) on the grinder body unscrewing it gently to feel for alignment of the two threads

and thus to be able to feed them in without using force. Then tighten until the 2

grindstones come into contact (fig. K).

10.Unscrew the "adjustment nut" (5) to free the grindstones in contact.

11.Plug the machine in and switch it on with no coffee.

12. While pressing the indexing pointer with one hand, with the other screw up the

"adjustment nut" (5) until the 2 grindstones make slight contact.

13.Stop the machine.

14.Unscrew the graduated plate (12) retaining screws and re-index the graduated plate

"0" with the indexing pointer (7) (fig. L).

15.Unscrew the "adjustment nut" (5) by 5 to 10 notches

16.With coffee, adjust the ground coffee setting (see "Coffee grinding adjustment"

section).

98140 US 3.0 - 05 2007 9 / 20 www.santos.fr

SANTOS : User and maintenance manual

FAULT FINDING

Carefully determine the reason for the machine stopping.

In all circumstances, if the problem persists, disconnect the electric power supply (unplug

the mains supply lead plug (10)) and call on someone from the maintenance department or

contact an approved SANTOS dealer.

Where appropriate, do not forget to close the bean container shutter (6) before removing the

container.

The machine will not start:

•Check: the mains power supply and the condition of the power supply lead (10).

•Check that the On / Off switch indicator (11) lights up when the switch is in the 1

position. If not, replace the switch.

•Check that the grindstones (9) are not making contact preventing the motor from

starting.

•Check that there are no foreign bodies stuck between the grindstones.

•Inside the machine, check the condition of the electric wiring and the connections (on

the switch (11), on the component support module (20) (fig. N) (the electric

components can be accessed without dismantling the machine) and on the dose

measurer automatic device unit (19) (fig. M)).

•Check the electric components, replacing them one by one.

The machine stops as a result of motor over-heating: (the motor unit is hot)

The motor is protected by an integral thermal protection. If the motor overheats, it stops.

•Check that there are still coffee beans in the bean container (2).

•Put the On / Off switch (11) to the 0position and unplug the machine.

•Wait for the motor to cool down (20 to 45 minutes) then press the On / Off switch (11)

(position 1).

The machine stops as a result of an overload:

A foreign body between the grindstones, grindstones making contact, a too fine coffee

grinding or intensive operation may result in a motor overload.

Under these circumstances, either the thermal protection or the excess current protection

may be activated and stop the machine operating.

If the machine is hot, refer to the section "The machine stops as a result of motor over-

heating").

Otherwise:

•Turn off the electric power supply (unplug the mains power lead (10))

•Move the On / Off switch (11) to the 0position.

•Under the machine (fig. O), press the button (13) to reset the excess current

protection. If the button does not remain in the "reset" position, allow the machine to

cool down before repeating the operation.

98140 US 3.0 - 05 2007 10 / 20 www.santos.fr

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Santos Macchina per il caffè

Santos

Santos 75 Istruzioni operative

Manuali Macchina per il caffè popolari di altre marche

Taurus

Taurus Livorno 6 Manuale utente

Delta-q

Delta-q QUICK Manuale utente

Bunn

Bunn LCA-1 Guida alla risoluzione dei problemi

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Istruzioni per l'installazione

Saeco

Saeco Vienna Plus Sup 018M Manuale utente

DeLonghi

DeLonghi DC300 Manuale utente

INCAPTO

INCAPTO BXCO1470E Manuale utente

Bosch

Bosch TASSIMO finesse TAS16B Series Manuale utente

Exido

Exido 245-072 Manuale utente

Animo

Animo OptiVend Choco Manuale utente

Siemens

Siemens TQ505DF Series Manuale utente

DeLonghi

DeLonghi ECI341 Manuale utente

Krups

Krups KT406511 Manuale utente

Cimbali

Cimbali M32 Classic Manuale utente

Philips

Philips HL3844N Manuale utente

Bosch

Bosch TES 515 SERIES Manuale utente

Tekmatix

Tekmatix TMFM - 65 Manuale utente

Scarlett

Scarlett SC-CM33005 Manuale utente