SANTRONIC HDC-HDBW3200 Manuale utente
HDC-HDBW3200
Quick Start Guide
Version 1.0.0
i
Welcome
Thank you for purchasing our digital camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated DC 12V/AC 24V in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
ii
The grounding holes of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Camera Unit
■
■
1
Quick Start
Guide
■
■
1
CD
■
■
1
iii
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
2Framework...................................................................................................................................2
3Installation....................................................................................................................................3
3.1 Device Installation ........................................................................................................3
3.2 Lens Adjustment...........................................................................................................6
3.3 System Connection......................................................................................................6
4OSD Button .................................................................................................................................8
5HDC Configuration Tool ............................................................................................................9
5.1 Overview........................................................................................................................9
5.2 Operation .......................................................................................................................9
Appendix Toxic or Hazardous Materials or Elements ...............................................................13
1
1General Introduction
1.1 Overview
This series camera conforms to the HD-SDI specifications. It supports high speed video signal,
almost no delaying in the transmission. The HD-SDI interface adopts the coaxial cable and uses
the BNC port as the cable standard.
This series product has the megapixel definition and supports the DC 12V/AC 24V power
supplying.
1.2 Features
Data
Transmission
Support digital HD-SDI output.
Support analog output.
Peripheral
Equipment
Support peripheral equipment connection via the RS485 port. Support
Dahua protocol.
Power
External power adapter. Support DC 12V/AC 24V power supply.
Assistant
Function
Day/Night mode auto switch (ICR switch.)
Backlight compensation: screen auto split to realize backlight
compensation to adjust the bright.
Support auto aperture function.
2
2Framework
This series camera dimension and structure information is shown as below. The unit is mm. See
Figure 2-1 and Figure 2-2.
Figure 2-1
Figure 2-2
3
3Installation
3.1 Device Installation
Step 1
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome
cover and then open the cover. See Figure 3-1.
Figure 3-1
Step 2
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome
and then remove the device pedestal. See Figure 3-2.
With IR light Without IR light
Figure 3-2
4
Step 3
Draw out the cable exit and four screw holes in the installation position according to the device
pedestal. Dig the four plastic expansion bolt holes and cable exit. Insert the four plastic
expansion bolts into the screw holes.
Step 4
Adjust the camera pedestal to the proper position and then draw the cable through the cable exit
you just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four
plastic expansion bolt holes in the installation position. Put the four self-tapping screws in the
device pedestal and then use the screwdriver to secure the screws in the four plastic expansion
bolts firmly.
Step 5
Adjust the device position and line up the three inner hexagon screws of the device to the three
holes of the installation position. Put the three inner hexagon screws into the screw holes at the
bottom of the pedestal. Use the inner hexagon screwdriver to fix firmly. Connect the ground cable
to the GND port to improve stability. See Figure 3-3.
With IR light Without IR light
Figure 3-3
Step 6
Adjust the X-Y-Z axis module to turn the device to the proper monitor angle. Please follow the
steps listed below to adjust. See Figure 3-4.
Please note, for the dome of the IR light, you can skip step a) and step e).
a): Slightly push the two sides to squeeze the plastic hook so that you can take off the dome
enclosure.
b):Slightly loose the screws at the two sides of the X-Y-Z module manually, you can adjust
the module tilt rotation angle (15°～90°).
5
c):Slightly loose the screw of the pressing slice, you can adjust the video rotation angle of
the module (0°～355°).
d):Adjust the turning ring of the pedestal, you can adjust the module pan rotation angle
(0°～355°).
e): Put the enclose back after you completed the setup.
With IR light Without IR light
Figure 3-4
Please note, the screws in the following figure are the optical adjustment component.
Please make sure it is outward and do not allow it to touch the X-Y-Z axis module. See
Figure 3-5.
Figure 3-5
Step 7
Put the dome cover back and then put the three inner hexagon screws into the holes of the
device. Use the inner hexagonal wrench to fasten these three screws. See Figure 3-6.
6
Figure 3-6
3.2 Lens Adjustment
Step 1
Slightly loose the screw B manually and then turn the screw B slowly. Adjust the lens focus
distance to the proper position according to the monitor video. See Figure 3-7.
Step 2
Use the flat screwdriver to loose the screw A slightly and then turn the Screw A slowly. Adjust the
lens focus to get the clear video and then use the flat screwdriver to secure the screw firmly.
Step 3
When you are adjusting the screw A, the video may becomes blur. Please slightly adjust the
screw B manually to get the vivid video. Finally fix the screw.
Step4
Lay the aperture plate on the lens flatly. Please note this step is for IR device only.
With IR light Without IR light
Figure 3-7
3.3 System Connection
Indice
