Sanyo Denki SANUPS E11A Series Manuale utente

Uninterruptible Power Supply

E11A(TYPE C) Series

A11F102/152 Series

Contact Signal Interface Card

（Terminal type）

User Manual

Table of Contents

Introduction

Safety Precautions

1. Confirming Package Contents -------------------- 1

2. Contact Signal Interface Card Part Names ---- 1

3. Contact Signal Interface Card Installation ------ 2

4. UPS Settings ------------------------------------------ 5

5. External Signals (“CONTACTS SIGNAL”) --------8

6. Special Functions ---------------------------------------9

SANYO DENKI CO., LTD.

DWG.No. M0009173C

Introduction

Thank you for choosing this product. This document contains important safety

precautions for users and service technicians.To ensure proper operation and

reliability throughout the useful life this device, read this manual prior to use and

keep it nearby for future reference.

Safety Precautions

Read this manual carefully before installing, operating, performing maintenance, or

inspecting this device in order to understand all instructions and related safety

precautions.

Usage and Storage Precautions

Never operate or store the equipment in the following environmental

conditions, as doing so may cause malfunction, damage or deterioration,

which could result in fire and/or injury:

zIn ambient environmental conditions other than those specified

(temperatures outside the range of 0 to 40°C (32 to 104°F), and relative

humidity outside of the range of 30% to 90%).

zWhere the device is exposed to direct sunlight.

zWhere the equipment is directly exposed to heat from a heat source, such

as a stove.

zWhere the device may be subject to vibration or physical shock.

zNear a device that may emit sparks.

zIn the presence of dust, salt, or corrosive or flammable gas.

zOutdoors.

CAUTION

！

- 1-

1. Confirming Package Contents

When opening the package, confirm that the following items are included.

Contact your nearest sales representative if you find any discrepancy.

・Contact Interface Card 1 set

・Communication Cable (20cm) 1 pcs

・User Manual (this document) 1 copy

2. Contact Signal Interface Card Part Names

Fig. 2-1 Contact Signal Interface Card Exterior (Front View)

Fig. 2-2 Contact Signal Interface Card Exterior (Bottom View)

Table 2-1 Parts Description

Name Description

①AUX IN

(D-SUB 9-pin female)

Connector for communication with the UPS:

When receiving the status signal from the UPS*,

power will also be supplied to the contact signal

interface card.

②CONTACTS SIGNAL

(TERMINAL BLOCKS)

External status signal connector:

Outputs the UPS status signals via dry (no

voltage) contacts.

* UPS is an abbreviation for “Uninterruptible Power System”.

①②

①

②

- 2-

3. Contact Signal Interface Card Installation

Follow steps (1) through (6) to install the Contact Signal Interface Card.

Caution:

•If the device is shipped with the Contact Signal Interface Card preinstalled,

proceed from step (5).

(1) Preparation

The Contact Signal Interface Card should be installed only after the UPS has been

shut down completely. If the UPS is in operation, follow the instructions of “Operation

Shutdown (If UPS is not to be used for a week or more)” in the UPS Instruction

Manual, and shut down the UPS completely.

CAUTION

！

Before installing the Contact Signal Interface Card, the UPS

must be completely shut down. Inserting the card when the

UPS is not shut down completely may result in electric shock.

(2) Remove the protective cover

Remove the cover from the rear panel of the UPS.

①Remove the screws from both locations, and then the cover from the UPS.

Note that one of the screws will be used for securing the Contact Signal Interface

Card.

Note: The protective cover will not be used after inserting the card, but should

be stored in a safe place in case of future need.

Fig. 3-1 Rear panel cover removal（E11A）

①

Two screws

- 3-

(3) Insert the Contact Signal Interface Card

Insert the Contact Signal Interface Card into the card slot on the rear panel of

the UPS as shown in the Fig. 3-2.

Fig. 3-2 Inserting the Contact Signal Interface Card (UPS rear panel)

(4) Secure the Contact Signal Interface Card

Secure the Contact Signal Interface Card to the UPS using one of the screws

removed in step (2).

Insert the remaining screw into the cover securing position, to prevent losing

it.

Contact Signal Interface Card

Cover securing position Contact Signal Interface

Card securing position

- 4-

(5) Connect the Contact Signal Interface Card and the UPS using the accessory

cable

Use the communication cable to connect the “CARD I/F” connector of the

UPS and the “AUX IN” connector of the Contact Signal Interface Card as

shown in the Fig.3-3.

Fig. 3-3 Connection to the UPS using the communication cable (UPS rear panel)

(6) Connect the computer and the Contact Signal Interface Card using the

signal cable

Use the special signal cable to connect the “CONTACTS SIGNAL” TERMINAL

BLOCKS of the Contact Signal Interface Card to the computer.

Contact Signal

Interface Card

AUX IN

UPS

CARD

I/F

Computer

(Load devices)

Connect with the signal cable

Communication cable

(Accessory)

When the UPS is E11A series, Installation of the Contact Signal

Interface Card and the UPS setting procedures are now complete.

Start the UPS according to the procedures in the UPS Instruction Manual.

Even if interface setteing of E11A is set to “Workstation mode” or to

“Standalone mode”, UPS works.

In addition, you cannot use the Contact Signal Interface Card and the LAN

Interface Card at the same time.

In the case of E11A, only TYPE C can be connected to this CARD.

- 5-

4. UPS Settings（A11F series）

There are two communication mode settings for the UPS.

•Standalone mode

•W/S mode (Workstation mode)

Set the UPS to Standalone mode when using this Card.

Follow the procedures described on pages 6～7 to verify and change the UPS

mode settings.

Note that if the card was factory preinstalled, this step is unnecessary.

Caution:

If the UPS is set to W/S mode, the Interface Card cannot be used.

Also, this card cannot be used with power control software (SANUPS SOFTWARE)

that requires a PC I/F connector for serial connection. If PC shutdown capability is

required while using this Card, the communication settings in the power control

software must be set to “Contact Connection”.

- 6-

01 2

Mode verification and setting modification

(1) Start the UPS

Operating mode verification and setting changes are done using the operating unit

and the display of the UPS front panel. Begin by starting the UPS.

Follow the procedures for startup operation as described in the UPS Instruction

Manual.

(2) Verify the operating mode and modify settings using the operating unit and

the display

Verify the operating mode and modify settings

following the procedures described in the UPS

Instruction Manual.

(3) Disable the Automatic startup

Verify and change settings following the

procedures described in the UPS Instruction

Manual.

For more information about the ring signal

startup, refer to "§6 Special Functions" of this

manual.

Fig. 4-1 LED display when standalone mode is selected

Caution:

When the UPS starts, power will be supplied from the outlet.

It is recommended to disconnect the load devices before starting the UPS.

●－Blinking

○－Off

●－Blinking

○－Off

Fig. 4-2 LED display when the ring signal is set to “Disabled”

- 7-

(4) Stop the UPS

When setting modifications are complete, stop the UPS. Follow the

procedures of the UPS Instruction Manual to properly shut down the UPS.

Installation of the Contact Signal Interface Card and the UPS setting

procedures are now complete.

Start the UPS according to the instructions in the UPS Instruction Manual.

Caution:

•If any load devices were disconnected, reconnect them at this time.

•If any settings were modified, stop the UPS completely. Otherwise,

any changes in the settings are not validated, and will not take effect.

- 8-

5. External Signals (“CONTACTS SIGNAL”)

Signal Name Description

AC Input Fault

This signal is output when there is a failure in the

commercial power supply, or when voltage is

insufficient. (Make contact, Break contact)

Low Battery voltage

This signal is output when the battery voltage falls

below the preset value. (Make contact or Break

contact. Default : Make contact) Note 3

AC Output

This signal is output when AC output is supplied to

the load devices via OUTPUT1 or 2.

(Make contact, Break contact) Note2

Bypass Output

This signal is output when bypass output is

supplied to the load devices. (Make contact or

Break contact. Default : Make contact) Note 3

Signal

output

UPS Fault

This signal is output when a fault occurs in the

UPS. (Make contact or Break contact.

Default:Makecontact) Note3

Note 1．These signal outputs are non-voltage contacts, with a contact

capacity of AC 110V/DC 24V 0.2A.

Note 2．In the case of A11F, when using OUTPUT1,2 and supplying the

output, this Card output a signal.

Note 3．“Low Battery voltage”, “Bypass Output” and “UPS Fault” can

choose of Make contact or Break contact. Default is Make contact.

Fig. 5-1 Contact Signal Interface Card Exterior (Bottom View)

Note: The figure above shows the device’s status when stopped.

TERMINAL BLOCKS

①②③④⑤⑥⑦⑧

Low Battery Voltage

Bypass Output

AC Input Fault

AC Output

UPS Fault

8 (COM)

JP1A

JP1C

JP1B

UPS Fault

Low Battery voltage

Bypass Output

b a b a b a

Make contact

Break contact

Short pin

Altri manuali per SANUPS E11A Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Sanyo Denki UPS

Sanyo Denki

Sanyo Denki S-A11KL202B0015SS 00 Series Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11A102U-J Manuale utente

Sanyo Denki

Sanyo Denki Sanups ASE-H series Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11B-Li Manuale utente

Sanyo Denki

Sanyo Denki Sanups A11J Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11A102A Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11A Series Manuale utente

Sanyo Denki

Sanyo Denki Sanups A11J Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11A202U Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11B Manuale utente

Sanyo Denki

Sanyo Denki SANUPS ASE10S1HU002-08 Manuale utente

Sanyo Denki

Sanyo Denki SANUPS E11A Series Istruzioni utente

Sanyo Denki

Sanyo Denki SANUPS E11B Manuale

Sanyo Denki

Sanyo Denki SANUPS A11H Manuale utente

Sanyo Denki

Sanyo Denki SANUPS A11H Istruzioni utente

Sanyo Denki

Sanyo Denki ASD 35S2NU Manuale di istruzioni

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente