Sartorius 2405 Guida utente

Digital Micro Balances

2405

Instructions for installation and operation

1. UNPACKING

2. INSTALLATION OF THE BALANCE

2.1. Checking the voltage setting

2.2. Detaching the transport arrestment

2.3. Assembling the balance

2.4. Inserting the glass plates

2.5. Leveling the balance

3. DESCRIPTION OF THE OPERATING KNOBS

4. CHECKING AND ADJUSTING

4.1. Focusing the projection scale

4.2. Zero point

4.3. Sensitivity

5. WEIGHING PROCEDURES

6. SUPPLEMENT

6.1. Accuracy of the built-in set of weights

6.2. Correction of the weighing result

6.3. Determination of the air density

6.4. Conditions for installing micro balances

7. TECHNICAL DATA

1. Unpacking

1.1. Carefully remove the balance from their cartons.

1.2. Carefully unpack accessories.

2. INSTALLATION

2.0.1. IMPORTANT: see supplement 6.1. to 6.4.

2.0.2. Remove outer and inner lid.

2.1. Checking the voltage setting:

2.1.1. Place balance on the rear on to the plastic dust cover. Push the cover plate in the base plate aside

and change connecting wires, if necessary. Close the cover plate and set up the balance. Remove the

adhesive tape carefully and wipe off the arrears with alcohol.

2.2. Detaching the transport arrestment:

2.2.1. Weight application must indicate “29.99”.

2.2.2. Take off cover of the damping pot.

2.2.3. 3 Loosen knurled nuts, remove paper strips, swing aside springs and retighten nuts.

Remove cardboard strip.

2.2.4. Take out balance beam. Take off 3 plastic discs (1). Loosen 3 knurled nuts (2), swing aside springs

and retighten nuts.

2.2.5. Remove cardboard strip.

Connect balance to the mains. Press gray push button (see 3.1.).

2.2.6. Remove brackets at the ends of the locking bars of the weight application.

2.2.7. Pull out bars carefully.

2.3. Assembling the balance:

2.3.1. Check arrestment pins (1), damping (2) and bearing (3) and clean, if necessary.

2.3.2. Check knife-edges and bearing and clean, if necessary.

2.3.3. Set balance beam on to the arrestment pins (1). The knife-edge must not come into contact with the

bearing.

2.3.4. Place cover plate on to the damping pot and turn anti-clockwise until the slit the cover plate runs paral-

lel with the balance beam. Turn clamp clockwise until it locks.

2.3.5. Check stirrup plate and clean, if necessary. Set stirrup plate on to the arrestment pins.

2.3.6.2. Unscrew 2 knurled nuts and take off bow.

2.3.7. Attach stirrup and insert it.

2.3.8. Unscrew 2 knurled nuts and take down carefully the locking plate for the weights. Put back the perfo-

rated plate afterwards.

2.3.9. Attach lamp housing and plug in the cable.

2.3.10. Place the inside hood on to the balance.

2.3.11. Swing out pan lifting device. Open upper sliding door and attach pan bow.

2.4. Inserting the glass plates:

2.4.1. Place glass plate into the balance and close upper sliding door. Put the balance pan on to the holder

and swing in the pan.

2.4.2. Place glass plate into the balance and close sliding door.

2.4.3. Put locking screws for the front plate into position.

2.4.4. Fasten front plate.

2.4.5.Turn weight application to “0.00” and set micrometer to “00”.

Indice

Altri manuali Sartorius Scala

Sartorius

Sartorius G 150 D Manuale utente

Sartorius

Sartorius 1002MP9 Manuale utente

Sartorius

Sartorius Factory Series Manuale utente

Sartorius

Sartorius M-prove Series Manuale utente

Sartorius

Sartorius QC7CCE-S Manuale utente

Sartorius

Sartorius Cubis MCA Scheda tecnica

Sartorius

Sartorius Master Pro Series Manuale utente

Sartorius

Sartorius PMA.Power Manuale utente

Sartorius

Sartorius Cubis MCE Series Manuale utente

Sartorius

Sartorius Cubis MCA10202S Series Manuale utente

Sartorius

Sartorius MC 5 Manuale utente

Sartorius

Sartorius PMA.Evolution EVO1Y1 Manuale utente

Sartorius

Sartorius IB 31 Manuale utente

Sartorius

Sartorius CUBIS MSU Manuale utente

Sartorius

Sartorius 1401 MP8 Manuale utente

Sartorius

Sartorius M-Power AZ214 Manuale utente

Sartorius

Sartorius Entris Manuale utente

Sartorius

Sartorius EC1XS Manuale utente

Sartorius

Sartorius CPA 12001S Manuale utente

Sartorius

Sartorius M3P Manuale utente

Sartorius

Sartorius PMA.Evolution Manuale utente

Sartorius

Sartorius Basic lite Manuale utente

Sartorius

Sartorius EA Manuale utente

Sartorius

Sartorius Secura Manuale utente

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente