Satel SILVER Manuale utente

SILVER

DIGITAL DUAL TECHNOLOGY MOTION DETECTOR

silver_en 12/11

1. Features

•Combined PIR and microwave technology.

•Digital motion detection algorithm.

•Digital temperature compensation.

•Selectable operation modes: basic or advanced.

•Microwave based anti-mask feature

•Remote LED enable/disable.

•Alarm memory.

•Supervision of detector signal path and supply voltage.

•Capability of separate sensor testing.

•Tamper protection against enclosure opening.

2. Specifications

Supply voltage........................................................................................................... 12 V DC ±15%

Standby current consumption..................................................................................................18 mA

Maximum current consumption ...............................................................................................25 mA

Relay contacts rating (resistive load) ..................................................................... 40 mA / 16 V DC

Microwave frequency...................................................................................................... 10.525 GHz

Detectable speed.............................................................................................................. 0.3...3 m/s

Alarm signaling time ......................................................................................................................2 s

Security grade according to EN50131-2-4 ........................................................................... Grade 2

Standards complied with .................................EN50131-1, EN50131-2-4, EN50130-4, EN50130-5

Environmental class according to EN50130-5 ................................................................................ II

Operating temperature range .........................................................................................-30...+55 °C

Maximum humidity.................................................................................................................. 93±3%

Dimensions............................................................................................................62 x 136 x 49 mm

Recommended installation height ............................................................................................ 2.4 m

Weight ...................................................................................................................................... 126 g

The declaration of conformity may be consulted at www.satel.eu/ce

3. Operation modes

Basic – the detector indicates an alarm if both sensors detect motion within a time period shorter

than 3 seconds.

Advanced – the detector indicates an alarm if:

−both sensors detect motion within a time period shorter than 3 seconds;

−within a time interval less than 3 seconds, the microwave sensor detects motion and the

PIR sensor detects some changes in coverage area, insufficient however to be recognized

as motion;

−within 15 minutes' period, the microwave sensor detects motion 16 times, but PIR sensor

does not detect any changes in coverage area.

2 SILVER SATEL

4. Anti-mask feature

Detection by the microwave sensor of an object moving at a distance of 10-20 centimeters from

the detector is interpreted as an attempt to mask the detector and results in opening the anti-

masking relay contacts for two seconds. Objects permeable to microwaves, but isolating the

infrared radiation are not detected by the anti-masking feature.

5. Supervision features

In the event of the signal path failure or the voltage drop below 9 V (± 5%) for more than

2 seconds, the detector will signal a trouble. The trouble is indicated by the activation of alarm

relay and the steady red light of LED indicator. The trouble signaling will continue as long as the

trouble persists.

6. Electronics board

terminals:

WRN - anti-masking relay (NC).

TMP - tamper contact (NC).

COM - common ground.

12V - power supply input.

NC - alarm relay (NC).

LED - remote LED control (the LED pins

must be open). The LED is enabled

when the input is short-circuited to

common ground. To control the input,

you can use the OC type output of the

control panel, programmed e.g. as

SERVICE MODE INDICATOR or BI SWITCH.

MEM - alarm memory control. When the input

is short-circuited to common ground

and the detector signals alarm, the

LED will indicate the alarm memory.

Disconnecting the input from common

ground will not clear the alarm

memory. Signaling the alarm memory

will continue until the input is shorted

to common ground again. To control

the input, you can use the OC type

output of the control panel,

programmed e.g. as ARM STATUS.

microwave sensor.

two-color LED to indicate:

– alarm – LED lit up red for 2 seconds;

– motion detection by one of the sensors – LED lit up green for 2 seconds;

– warm-up – LED flashing alternately red and green;

– trouble – LED lit up red.

potentiometer for sensitivity adjustment of the microwave sensor. Please bear in mind that

microwaves can penetrate e.g. glass, gypsum walls, non-metallic doors, etc.

potentiometer for sensitivity adjustment of the PIR sensor.

MODE pins – selecting the detector operation mode:

– pins shorted – basic mode;

– pins open – advanced mode.

SATEL SILVER 3

LED pins – enable/disable LED indicator. The LED indicator is enabled when the pins are

shorted (remote LED control is not possible then).

dual pyroelectric sensor.

tamper contact.

fixing screw hole.

7. Installation

Do not touch the pyroelectric sensor, so as not to soil it.

1. Open the enclosure (Fig. 2).

2. Remove the electronics board.

3. Make the openings for screws and cable in the enclosure base.

4. Pass the cable through the prepared opening.

5. Fix the enclosure base to the wall or to the attached bracket (Fig. 3 and 4).

6. Fasten the electronics board.

7. Connect the wires to the corresponding terminals.

4 SILVER SATEL

8. Using potentiometers and jumpers, set the working parameters of the detector.

9. Close the detector enclosure.

8. Start-up and walk test

1. Turn the power on. The detector warm-up lasts 30 seconds. During that time, the detector

stabilizes and the LED indicator (if enabled) is alternately flashing red and green.

2. After completion of the warm-up, check that motion within the coverage area (Fig. 5) will

activate the alarm relay and the LED indicator will light up red.

9. Separate testing of sensors

To test the microwave sensor, do the following:

1. Before you turn the power on, put the jumper on the MODE pins.

2. Turn the power on and, during the warm-up, remove the jumper from the MODE pins. After

completion of the warm-up, the LED should flash green every 3 seconds.

3. Check that movement within the coverage area will activate the alarm relay and the LED

indicator will light up green.

To test the PIR sensor, do the following:

1. Before you turn the power on, remove the jumper from the MODE pins.

2. Turn the power on and, during the warm-up, put the jumper on the MODE pins. After

completion of the warm-up, the LED should flash red every 3 seconds.

3. Check that movement within the coverage area will activate the alarm relay and the LED

indicator will light up red.

Note: The sensor separate testing mode is automatically exited after 20 minutes.

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

[email protected]

www.satel.pl

Altri manuali per SILVER

Indice

Altri manuali Satel Sistema di sicurezza

Satel

Satel SD-3001 Manuale utente

Satel

Satel INT-TSG Manuale del proprietario

Satel

Satel ABAX 2 Manuale utente

Satel

Satel SP-4003 R Manuale utente

Satel

Satel ASP-105 Manuale utente

Satel

Satel ABAX 2 Manuale utente

Satel

Satel ASP-201 Manuale utente

Satel

Satel SPL-5010 Manuale utente

Satel

Satel SPL-2010 Manuale utente

Satel

Satel SOW-300 Series Manuale utente

Satel

Satel MSP-300 Manuale utente

Satel

Satel ASP-105 Manuale tecnico

Satel

Satel Integra 24 Guida utente

Satel

Satel ROP-101/EU Manuale utente

Satel

Satel CA-4M Istruzioni operative e di manutenzione

Satel

Satel SPLZ-1011 Manuale utente

Satel

Satel ABAX 2 Manuale utente

Satel

Satel SPW-100 Manuale utente

Satel

Satel CA-64 E Manuale utente

Satel

Satel MSP-300 Manuale utente

Satel

Satel ABAX 2 ASP-200 Manuale utente

Satel

Satel CA-64 E Manuale utente

Satel

Satel SP-6500 Manuale utente

Satel

Satel ASP-105 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente