Satel SP-500 Manuale utente

VISUAL-AUDIBLE SIREN

SP-500

sp500_en 04/09

The SP-500 visua -audib e siren is designed for app ication in the burg ary and assau t

signa ing systems. A set of LEDs situated at the ower part of the siren enc osure serves as

the source of ight. A modu ated acoustic signa is generated by means of the piezoe ectric

transducer. Any attempt to open the siren or tear it off from the mounting surface wi set off

a tamper a arm. The e ectronics board is protected by impregnation against unfavorab e

effects of weather conditions. As the SP-500 housing is made of the high y impact resistant

PC LEXAN po ycarbonate, hence it features a high mechanica strength and guarantees

aesthetic appearance of the siren even after many years of operation.

Fig. 1. View of the SP-500 siren enc osure.

Exp anations for Figure 1:

1 – fixing screw ho es

2 – piezoe ectric transducer

3 – cab e in et

4 – e ectronics board

5 – cover fixing screw

6 – cover openings

7 – piezoe ectric transducer eads

8 – tamper e ement – protects the siren from removing its enc osure and/or tearing it off

from the wa (must be screwed to the mounting surface; do not overtighten, so as not

to break the narrowings)

9 – opening for tamper e ement fixing screw

10 – water drain opening (do not stop)

2 SATEL SP-500

Fig. 2. Tamper e ement and its equiva ent – reed re ay switch.

Exp anations for Fig. 2:

1 – cab es for connecting tamper circuit e ement with p ate

2 – fixing screw opening for reed re ay switch

3 – so dering points of reed re ay switch

1. Outfit options

Additiona protection e ements (so d separate y) can be insta ed in the siren. They inc ude:

• inner cover of ga vanized sheet, OM-SP500;

• hermetic reed re ay tamper switch, SD/SP-SAB.

Where the reed re ay switch is used, it is necessary to remove the mechanica switch

insta ed by the manufacturer on the tamper e ement, and rep ace it with the new switch. This

operation requires reso dering of the two cab es which connect it with the e ectronics of the

siren (see Fig. 2).

2. Installation

The SP-500 siren is to be insta ed on a f at surface, in a possib y inaccessib e p ace, so as to

minimize the risk of tampering. The siren shou d be screwed to its base by means of screws

and expansion bo ts (the screws and expansion bo ts are de ivered with the siren).

Note: Make sure to leave a distance of about 0.5 cm between the upper edge of the siren

base and the ceiling or another element which limits the mounting position from

above. The lack of such clearance can make the mounting of housing difficult.

After the siren has been insta ed, it is recommended that the fixing screw ho es and the

cab e entry opening be sea ed with si icone compound.

3. Description of siren functioning

The SP-500 siren can work together with any source of a arm signa which, in the a arm

condition, provides 12 V direct vo tage on the signa ing output (outputs). The audib e

signa ing of the SP-500 wi be activated after connecting the 12 V power supp y to the

"+ SA -" termina s, whi e the visua signa ing wi switch on when the 12 V power is supp ied to

the "+ SO -" termina s.

The "TMP" termina s are designed for connecting the siren to the tamper circuit of the a arm

system.

You can choose one of the three types of acoustic signa ing.

SP-500 SATEL 3

JP1

JP2

JP3

JP4

JP5

JP1

JP2

JP3

JP4

JP5

MEL1=JP1+JP4 MEL3=JP3+JP5

MEL2=JP2+JP5

zworka założona

zworka zdjęta

JP1

JP2

JP3

JP4

JP5

Fig.3. P acing jumpers in different ways across pins to obtain the required audib e signa .

4. Hoo ing Up

It is possib e to contro two types of signa ing from one contro pane output when the

termina s are connected in para e : +SA with +SO and -SA with -SO.

SP-500

TMPTMP

OUT3

OUT4

OUT5

OUT6

OUT7

OUT8

INTEGRA 32

AUX Z1 COMCOM CK

COM Z2

CKM +EX DT+KPD DTM

OUT2

Fig. 4. Method of connecting the SP-500 siren to ow-current outputs of INTEGRA 32

contro pane . Output OUT2 has been programmed as supp y one. Output OUT3 contro s

the re ay P1 which triggers acoustic signa ing, and output OUT4 contro s the re ay P2

which triggers optica signa ing ( ow-current outputs with norma po arization are activated

by shorting the termina direct y to ground 0 V). Zone Z2 shou d be programmed

as 24 h tamper.

– pins shorted

– pins open

4 SATEL SP-500

Description of termina s:

+SO- – optica signa ing termina s

+SA- – acoustic signa ing termina s

TMP – tamper circuit termina s

INTEGRA 32

COM OUT1 COM COM COM COMOUT2 +KPD DTM CKM +EX CK AUX Z1

OUT1 COMCOM COM Z1

OUT2

SP-500

SO TMP TMP

Fig. 5. Method of connecting the SP-500 siren to high-current outputs of INTEGRA 32

contro pane . Output OUT1 triggers optica signa ing and output OUT2 – acoustic signa ing

(the high-current outputs with norma po arization – activation means that +12 V vo tage is

supp ied). Zone Z1 shou d be programmed as 24 h tamper zone, and outputs OUT1 and

OUT2 as a arm outputs (BURGLARY or FIRE/ BURGLARY).

Some contro pane s may require a resistor R (about 1kΩ) to be insta ed between the +SA-

termina s in the siren. Otherwise, the siren wi buzz si ent y when switched off.

5. Technical Data

Supp y vo tage .................................................................................................... 12V DC ±20%

Average current consumption when signa ing

acoustic signa ing ...................................................................................... 250 mA

optica signa ing ..........................................................................................35 mA

Sound intensity ................................................................................................... approx.120 dB

Environmenta c ass ................................................................................................................ III

Working temperature......................................................................................... -35oC…+55oC

Siren dimensions ......................................................................................... 300 x 195 x 97mm

Siren weight ...................................................................................................................... 651 g

SATEL sp. z o.o.

u . Schuberta 79

80-172 Gdańsk

POLAND

te . (+48 58) 320 94 00

www.sate .p

info@sate .p

Latest EC dec aration of conformity and

product approva certificates can be

down oaded from our Web site www.satel.pl

Indice

Altri manuali Satel Sistema di sicurezza

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente