Savi SAVI-NOTE75 Manuale utente

InstallatIon Manual

Super Vision International • 8210 Presidents Drive • •Orlando, Florida 32809 •• 407.857.9900 • Fax 407.857.0050 • www.svision.com

SaVi Note Underwater LED Light

SAVI-NOTE75, SAVI-NOTE150

Model NuMbers

Super Vision International • 8210 Presidents Drive • •Orlando, Florida 32809 •• 407.857.9900 • Fax 407.857.0050 • www.svision.com Super Vision International • 8210 Presidents Drive • •Orlando, Florida 32809 •• 407.857.9900 • Fax 407.857.0050 • www.svision.com

Table of ConTenTs

Safety Precautions ........................................................2

SaVi Note Install Instructions ........................................3-4

M4 Instructions ...............................................................5-11

Warnings

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

I. SAFETY PRECAUTIONS

To prevent electrocution and/or death make sure power is off at the breaker.

Avoid touching/installing the M4 controller box during electrical storms. Death

or serious injury may result due to lightning surges through the system.

Be sure to check local electrical codes for grounding electrical boxes via

the approved method (internal conduit ground, external box ground wire to

grounding rod, etc.)

Use approved conduit routed by approved methods to conduit ﬁttings on the

box.

For DMX based units, do not install data cables in the same conduit as power

cables to prevent communication problems.

Be sure the mounting surface is able to support the load of the controller. Use

all four mounting holes to secure the controller.

There are no customer serviceable components inside the M4 controller. Only

qualiﬁed electricians should open the box for installation of the power and LED

accessories connections. All connections should enter through an approved

conduit method.

LED accessories are low voltage and should never be electrically connected

to any power source other than the appropriate M4 controller connector (J5

to J8). Wires must be connected properly to avoid permanently damaging the

LED accessory.

WARNING

insTallaTion insTruCTions

INSTALLATION INSTRUCTIONS

STEP 1

The light ﬁxture must be installed in

or on a wall of the pool with the top

of the lens opening not less than 4

inches (10.16cm) below the normal

water level of the pool except when

the ﬁxture is installed in an area

of the swimming pool that is not

used for swimming and the lens is

adequately guarded to prevent any

person from contacting it.

STEP 2

Snake the 4-conductor electric

cord through the conduit outlet

of the wall ﬁtting, into the conduit

and up to the M4 controller. DO

NOT CUT EXCESS CORD. Leave

adequate cord in the conduit (Do

NOT wrap cord around ﬁxture) so

that ﬁxture will be able to be raised

to deck if required. Cut off extra

cord after, allowing for service

and length of run to box. Pull the

ﬁxture snug to the wall ﬁtting.

4” MIN. FROM WATER

LEVEL TO TOP OF LENS

4” MIN. FROM WATER LEVEL TO

TOP OF LENS

M4 Controller

Conduit to M4

SaVi Note

insTallaTion insTruCTions

STEP 3

Using the lens wrench, thread the ﬁxture

into the wall ﬁtting until it is snug.

STEP 4

Wire the ﬁxture to the M4 Controller. See M4 instructions on pages 5-11.

STEP 5

Remove the protective cover before startup.

Super Vision International • 8210 Presidents Drive • •Orlando, Florida 32809 •• 407.857.9900 • Fax 407.857.0050 • www.svision.com

InstallatIon Manual

M4 LED CONTROLLER

For SaVi Notes and X-Stream LED Modules

M4-L, M4-H, M4-L-DMX, M4-H-DMX

Model NuMbers

Super Vision International • 8210 Presidents Drive • •Orlando, Florida 32809 •• 407.857.9900 • Fax 407.857.0050 • www.svision.com

INSTALLATION INSTRUCTIONS

II. MOUNTING

Select a mounting location so that the bottom

surface of the enclosure will be at least twelve

(12”) inches above the ground (See FIGURE 1).

Be sure to provide enough clearance below the

box to route the power, communications, and

LED accessory conduits as desired.

Place the controller at the location desired and

mark the location of the upper two mounting

holes.

Drill holes as appropriate (wood, masonry block,

brick, etc.) for the mounting hardware. Be sure to use a mounting method that

can withstand the weight of the controller and the attached conduits.

Temporarily secure the box to the mounting surface using the method selected.

Mark the position of the lower two holes, remove the box, drill the lower two

holes, and prepare the lower mounting locations.

Secure the four mounting screws or bolts to complete the mounting of the M4

controller.

III. CONDUIT AND GROUND CONNECTIONS

1. After selecting the desired conduit

size (½” or ¾”), carefully remove

the appropriate “knock outs” in the

bottom of the enclosure while being

careful not to touch the PCB (Print-

ed Circuit Board).

2. Install the power, communication,

and LED accessory conduit ﬁttings

as desired to the enclosure (see

FIGURE 2).

3. Pull cables through to the ends

of the conduit. Leave extra cable

length to allow preparation and in-

stallation of the wires.

MounTing insTruCTions

DUE TO THE DESIRED WATER RESISTANT SEAL OF THE ENCLOSURE, DO NOT RE-

MOVE ANY KNOCKOUTS UNLESS THAT HOLE WILL HAVE A CONDUIT INSTALLED.

IF A KNOCKOUT IS ACCIDENTALLY REMOVED, STEPS MUST BE TAKEN TO RE-

SEAL THE OPENING OR THE M4 CONTROLLER WILL BE DAMAGED.

WARNING

FIGURE 1

12”

above

ground

minimum

(J5)

FIGURE 2

A/C Service

conduit IN

DMX OUT

DMX IN

All in one

conduit

(optional)

LAMP IN #1 LAMP IN #2

LAMP IN #3 LAMP IN #4

(J6)

(J7) (J8)

Note: The left most conduit ﬁtting hole must

be used for installation of power to the con-

troller. The LED accessory and communica-

tions conduit connections should be placed

as shown in FIGURE 2.

inTernal Wiring

4. Install the ends of the conduit to the enclosure after routing the excess wire length

into the enclosure at the appropriate locations (see FIGURE 2)

5. If required by the local electrical codes or as desired, install a ground wire directly to

the enclosure using the external ground connection provided (not shown).

IV. INTERNAL WIRING

A/C Connections

Locate the power pig-tail provided with the M4 controller.

It will be located under the power supply and will consist

of one black (120 VAC), one white (neutral), and one green

(safety ground) wire.

Locate the incoming power wires from the conduit.

Trim excess lengths as desired and strip back approxi-

mately 3/8” of the insulation from all wires.

Twist the black wire of the M4 controller with the incoming

“120 VAC” wire. Install a wire nut or crimp using an ap-

proved insulated method (see FIGURE 3a).

FIGURE 3

POWER

SUPPLY

PCB - PRINTED

CIRCUIT BOARD

See FIGURE 3a

page 4

See FIGURE 3b

page 5

See FIGURE 4a

page 7

J6J5J4J3

See FIGURE 3c

page 7

POWER PIG-TAIL CONNECTION

FIGURE 3a

To M4

Power Supply To Ground

A/C

Line

(Black)

A/C

Neutral

(White)

A/C

Ground

(Green)

From A/C Input

Conduit

leD aCCessory ConneCTions

Twist the white wire of the M4 controller with the incoming “neutral” (not the ground)

wire. Secure as in “step (4)” (see FIGURE 3a).

Repeat for the green ground wire and the incoming ground wire (see FIGURE 3a).

Carefully tuck the wires into the area below the power supply while being careful

that the wires do not lay against the internal components of the power supply.

If possible, verify a grounding path exists between the incoming service ground wire

and the case of the M4 controller. If this is not possible, double check the ground

connection between the crimp and/or wire nut connection and the case of the M4

controller.

V. LED ACCESSORY CONNECTIONS (SaVi Notes or X-Stream LED Modules)

Locate the incoming cable for ﬁxture #1 (see FIGURE 2). This cable will be at-

tached to terminal block J5 on the PCB. Trim excess cable leaving no more than six

(6) inches protruding from the conduit.

Carefully remove two (2) inches of insulation from the cable (a box cutter set to pro-

trude less than 1/8” is good for this purpose). Cut from the desired removal location

towards the cut end of the cable to prevent damaging the internal wires.

Separate the insulation along the cut path and fold it back. Using cutters remove

the excess cable insulation. Only the four internal wires should be remaining (red,

green, blue, and a fourth conductor - usually black).

Using the wire stripper, remove 1/8 to 3/16” of insulation from each of the four

wires.

The wires will be installed as shown in FIGURE 3b below.

Insert each wire into the appropriate terminal block location. Using a small ﬂat

blade screwdriver, tighten each screw of the terminal block until you feel it com-

press the wire and become difﬁcult to turn (approximately 3.5 in-lbs).

DO NOT OVERTIGHTEN. Carefully pull on the wire to verify it is secure.

DUE TO THE DESIRED WATER RESISTANT SEAL OF THE ENCLOSURE, DO NOT RE-

MOVE ANY KNOCKOUTS UNLESS THAT HOLE WILL HAVE A CONDUIT INSTALLED.

IF A KNOCKOUT IS ACCIDENTALLY REMOVED, STEPS MUST BE TAKEN TO RE-

SEAL THE OPENING OR THE M4 CONTROLLER WILL BE DAMAGED.

WARNING

LED outputs must be connected as

shown to avoid damage to the circuit

Red

Black

Green

Blue

LED FIXTURE CONNECTION TO TERMINAL BLOCK

FIGURE 3b

#1 Position - Power Wire (usually Black)

#2 Position - Red wire

#3 Position - Green wire

#4 Position - Blue wire

DMX CoMMuniCaTion bus ConneCTions

7. Repeat for the remaining three wires of the cable (see FIGURE 3b). Tuck the excess

cable out of the way for the remaining steps.

8. Repeat steps 2-7 for ﬁxture #2 using the appropriate conduit input for location #2

(usually the back most to the right side) and J6 of the PCB (see FIGURE 3b).

9. Repeat steps 2-7 for ﬁxture #4 (it helps to install #4 before #3). Usually this will be

the front most conduit input to the right. Connect ﬁxture #4 to J8 of the PCB (see

FIGURE 3b).

10. Repeat steps 2-7 for ﬁxture #3. Connect ﬁxture #3 to J7 (bottom right) of the PCB

(see FIGURE 3b).

VI. DMX COMMUNICATION BUS CONNECTIONS (ON DMX UNITS)

Some M4 controllers use an optional serial communications bus (DMX bus) to commu-

nicate with a master controller. Some installations only require an incoming cable, while

other installations will require an input, as well as an output cable (proceeding on to the

next receiver/controller). This section details how to attach those connections.

Determine if the installation uses an input, or both an input and an output DMX con-

nection. An additional output connection can be added in the future if desired.

Locate the incoming DMX communication cable (see FIGURE 2). This cable will be

attached to terminal block J3 on the PCB. Trim excess cable leaving no more than

four (4) inches protruding from the conduit.

Carefully remove one and one-half (1-1/2) inches of insulation from the cable. The

cable is a twisted shielded pair type, so be careful to not damage the shield or the

internal wires.

Locate the actual shield “cable” within the overall “shield” (see FIGURE 3d) and

separate it from the individual shield wires. Carefully cut off and remove the shield

wires but NOT the small shield cable (see FIGURE 3d).

Using the wire stripper, remove 1/8 to 3/16” of insulation from each of the remaining

two wires.

DMX COMMUNICATION CABLE

DMX (+) / DMX(-) wires

Shield Cable

DMX (+) / DMX(-)

wires stripped

DMX Communication

cable

FIGURE 3d

Note: Before cutting the cables for ﬁxtures #3 & #4 (steps 9-10), verify the

desired internal routing location to J7 & J8. Be sure to leave enough cable to

reach the appropriate terminal block.

Note: Using an adhesive backed, tie wrap mount helps locating the cables

for ﬁxture #3 after tucking the cable for #4 along the right wall.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Savi Illuminazione subacquea

Savi

Savi MINI MEL P Manuale utente

Manuali Illuminazione subacquea popolari di altre marche

Keldan

Keldan VIDEO 18X 25000lm CRI82 Manuale utente

Oase

Oase ProfiLux Garden LED RGB Manuale utente

Oceanled

Oceanled DISCOVER D3 Manuale utente

NORBIT

NORBIT AQUA FCL600 Manuale utente

Keldan

Keldan VIDEO 8XR Ambient 18000lm Manuale utente

Ikelite

Ikelite PCm - LED Light Manuale utente

LIGMAN

LIGMAN NEMO 2 Manuale utente

Oase

Oase Lunaqua 2 Manuale

Kripsol

Kripsol 061511213000 Manuale utente

Wibre

Wibre 4.0291 Manuale utente

Certikin

Certikin PU9CS Manuale utente

lumishore

lumishore SMX53-SUPRA Manuale utente

Pyle

Pyle PLEDFN8 Manuale utente

Filix

Filix Arpool XM Manuale utente

Aqualuma

Aqualuma Pathway Light Manuale utente

HEISSNER

HEISSNER U 130-T Manuale utente

emaux

emaux NP300 Series Manuale utente

Oceanled

Oceanled XD16 Manuale utente