Savin 3705 Manuale utente

OPERATOR'S MANUAL

3705/9870

Read this manual carefully before you use this product and keep it handy for future reference.

For safety, please follow the instructions in this manual.

Savin OM3805&9870(Schmidt1CD).fm Page 1 Monday, May 29, 2000 9:13 PM

SUPPLIES

CAUTION : Savin shall not be responsible for any damage or expense that may result

from the use of parts other than recommended parts.

SAVIN CORPORATION

Type for Savin 3705/9870

Part No. H545-8631 Printed in China

(S1381)

UE USA June 2000

Savin OM3805&9870(Schmidt1CD).fm Page 2 Monday, May 29, 2000 9:13 PM

Optional Equipment

❖

HANDSET TYPE 100(Telephone Handset)

This permits voice communication (over the PSTN).

❖

FAX EXPANSION CARD TYPE 20

A 2-Mbyte memory card can be added.

USA

❖

FCC Requirements

1. This equipment complies with Part68 of the FCC rules. On thecover of this equipment isa label

that contains, among other information, the FCC registration number and ringer equivalence

number (REN) for this equipment. If requested, this information must be provided to the tele-

phone company.

2. This equipment uses the following USOC jack: RJ11C

3. The REN is used to determine the quantityof devices which may be connected to the telephone

line. Excessive REN's on the telephone line may result in the devices not ringing in response to

an incoming call. In most, but not all areas, the sum of the REN's should not exceed five (5.0).

Contact the telephone company to determine the maximum REN for the calling area.

4. If this equipment causes harm to the telephone network, the telephone company will notify you

in advance that temporary discontinuance of service may be required. If advance notice is not

practical, the telephone company will notify the customer as soon as possible. Also, you will be

advised your right to file a complaint with the FCC if you believe it is necessary.

5. The telephone company may make changes in its facilities, equipment, operations, or proce-

dures that could affect the operation of the equipment. If this happens, the telephone company

will provide advance notice in order to make necessary modifications in order to maintain unin-

terrupted service.

6. In the event of operation problems (document jam, copy jam, communication error indication),

refer to the solving problems section in this manual.

7. If you cannot correct the problem, please contact the SAVIN CORPORATION at 1-203-967-

5000 for repair and warranty information. If it is causing harm to the telephone network, the tel-

ephone company may request you to disconnect the equipment from the network until the prob-

lem is resolved.

8. This equipment cannot be used telephone company-providedcoin service. Connection to Party

Line Service is subject to state tariffs.

❖

WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO

EMERGENCY NUMBERS:

1. Remain on the line and briefly explain to the dispatcher the reason for the call before hanging

up.

2. Perform such activities in the off-peak hours, such as early morning hours or late evenings.

Notice

CAUTION:

Use of controls, adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

Shielded interconnect cables must be employed with this equipment to ensure

compliance with the pertinent RF emission limits governing this device.

Although this equipment can use either loop disconnect or DTMF signalling,

only the performance of the DTMF signalling is subject to regulatory require-

ments for correct operation. It is therefore strongly recommended that the equip-

ment is set to use DTMF signalling for access to public or private emergency

services. DTMF signalling also provides faster call set up.

Note

❒Some illustrations may be slightly different from your machine.

❒Certain options may not be available in some countries. For details, please

contact your local dealer.

-Notice about the Telephone Consumer Protection Act (Valid in USA

only).

The Telephone Consumer Protection Act of 1991 among other things makes it

unlawful for any person to send any message via a telephone fax machine unless

such message clearly contains in a margin at the top or bottom of each transmit-

ted page or on the first page of the transmission, the date and time it is sent and

an identification of the business, other entity, or other individual sending the

message and the telephone number of the sending machine or such business,

other entity or individual. This information is transmitted with your document

by the TTI (Transmit Terminal Identification) feature. In order for you to meet

the requirement, your machine must be programmed by following the instruc-

tions in the accompanying Operation Manual. In particular, please refer to the

chapter of Installation. Also refer to the TTI (Transmit Terminal Identification)

programming procedure to enter the business identification and telephone

number of the terminal or business. Do not forget to set the date and time.

Thank you.

Direct (or indirect reflected eye contact with the laser beam may cause serious eye dam-

age. Safety precautions and interlock mechanisms have been designed to prevent any

possible laser beam exposure to the operator.

ENERGY STAR Program

As an ENERGY STAR Partner, we have deter-

mined that this machine model meets the ENER-

GY STAR Guidelines for energy efficiency.

The ENERGY STAR Guidelines intend to establish an international energy-saving sys-

tem for developing and introducing energy-efficient office equipment to deal with en-

vironmental issues, such as global warming.

When a product meets the ENERGY STAR Guidelines for energy efficiency, the Part-

ner shall place the ENERGY STAR logo onto the machine model.

This product was designed to reduce the environmental impact associated with office

equipment by means of energy-saving features, such as Low-power mode.

iii

Energy Saving Modes

Energy Saving mode enables you to avoid using unnecessary power and econo-

mize on electricity. Although we recommend you use this mode from the view-

point of environmental consciousness, you can also turn it off.

When you install this machines for the first time, Energy Saving mode is turned

on by default.

Two types of Energy Saving mode are available:

• Fax Standby: Use when you receive faxes regularly.

• Energy Saving Standby: Use when you wish to economize on power con-

sumption.

Choose the one that best suits your circumstances.

Even though the operation panel display goes out in Energy Saving mode, Indi-

cators that flash or light during communication or reception still work. When the

Receive File indicator lights, exit Energy Saving mode and take the appropriate

action.

You can turn Energy Saving mode on or off with User Parameter Function 63.

When the machine is shipped, Energy Saving Standby is selected on.

The machine enters Energy Saving mode when:

• Nobody uses the machine for about 5 minutes (the machine automatically en-

ters Energy Saving mode)

• The user holds down the Energy Saver key for about 2 seconds.

Energy Sav-

ing Mode

Type

Status How long before

you can print after

exiting Energy

Saving mode

Power con-

sumption

Fax Standby Display turns off

The machine maintains the heating

roller temperature at half the full

temperature; warm up takes less

time. (Heater half cool)

Within about 30s 25W

Energy Sav-

ing Standby Display turns off

The machine lets the heating roller

cool to room temperature; warm-

up takes longer.(Heater off)

Within about 40s 2W

To exit Energy Saving mode:

• In Energy Saving Standby mode, press the Energy Saver key.

• In FAX Standby mode, press any key.

• Set a document.

• Pick up the optional handset or the external telephone handset.

Note

❒When you load paper in Energy Saving mode, no error will be displayed even

if the cassette is not pushed right in.

❒After loading paper, press the Energy Saver key and check that "READY”is

shown on the display.

The manual Receiver indicator goes out in Energy Saving mode even if Manual

Receive is turned on.

Reception in Energy Saving mode

In Energy Saving mode, documents that have been stored in memory are still

sent and the machine can still receive messages.

When a message is received in Energy Saving mode, the machine prints it and

returns to Energy Saving mode.

Limitation

It is not possible to enter Energy Saving mode when an original is set.

Laser Safety:

The Center for Devices and Radiological Health (CDRH) prohibits the repair of

laser-based optical unit in the field. The optical housing unit can only be re-

paired in a factory or at a location with the requisite equipment. The laser sub-

system is replaceable in the field by a qualified Customer Engineer. The laser

chassis is not repairable in the field. Customer engineers are therefore directed

to return all chassis and laser subsystems to the factory or service depot when

replacement or the optical subsystem is required.

Operator Safety :

This machine is considered a CDRH class I laser device, safe for office / EDP use.

The machine contains two 5-milliwat, 765 - 805 nanometer wavelength, GaAIAs

laser diodes. Direct (or indirect reflected) eye contact with the laser beam might

cause serious eye damage. Safety precautions and interlock mechanisms have

been designed to prevent any possible laser beam exposure to the operator.

In accordance with IEC 60417, this machine uses the following symbols for the

main power switch:

•ameans POWER ON.

•bmeans POWER OFF.

Note to users in the United States of America

-Notice:

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential in-

stallation. This equipment generates, uses and can radiate radio frequency ener-

gy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to cor-

rect the interference by one more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio /TV technician for help.

-Warning

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Examples Of Indications

Symbols Rmean a situation that requires you take care.

Symbols vmean “Hot surface”.

Symbols nmean “Do not touch”.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Savin Stampante tutto in uno

Manuali Stampante tutto in uno popolari di altre marche

Triumph Adler

Triumph Adler DC 2016 Manuale

Epson

Epson WorkForce WF-2510 Guida utente

Epson

Epson Stylus Scan 2000 Manuale di installazione e funzionamento

Epson

Epson PictureMate Snap PM 240 Manuale di istruzioni

Konica Minolta

Konica Minolta bizhub C35 Manuale utente

Brother

Brother MFC-J430w Manuale utente

Konica Minolta

Konica Minolta BIZHUB 558 Manuale utente

Lexmark

Lexmark MX710 Series Manuale

Brother

Brother MFC-9760 Manuale utente

Lexmark

Lexmark XC8155 Manuale utente

Lexmark

Lexmark X642E Manuale utente

Sharp

Sharp MX-2310U Guida

Aficio

Aficio 200 Manuale utente

Canon

Canon ImageCLASS 2300 Manuale

Ricoh

Ricoh Pro C900 Manuale utente

Lexmark

Lexmark X925 Manuale utente

Brother

Brother Business Smart MFC-J4510dw Manuale utente

Epson

Epson Stylus CX8400 Series Manuale utente