SBE 37-IMP-ODO Manuale utente

Release date 10

-28-15, Reference sheet version 007; Digital Firmware version 2.13.0 & later; IMM Firmware version 1.10 & later

Sampling Modes

•Polled – On command, wake up, run pump, take one sample, transmit data, and go to sleep.

•Autonomous – At pre-programmed intervals, wake up, run pump, sample, store data in FLASH memory, and go to sleep.

•Combo – On command, transmit last Autonomous sampling data.

•Averaging – On command, calculate and transmit average of Autonomous sampling data since last request.

Setup

1. Install AA lithium cells (Note: ODO MicroCATs use a battery pack with a yellow cover plate):

A. Remove modem end cap: Wipe dry housing/end cap seam. Remove 2 cap screws from end cap, and twist end cap counterclockwise. Pull end

cap out. Disconnect Molex connecting to battery pack. Wipe O-ring mating surfaces in housing with lint-free cloth.

B. Remove battery pack and install cells: Loosen captured screw in battery pack cover. Use handle to lift battery pack out of housing. Keep

handle upright. Unscrew yellow cover plate from top of battery pack assembly. Roll 2 O-rings on side of battery pack out of grooves. Insert

cells into battery pack, and roll 2 O-rings into grooves on side of battery pack. Align pin on battery cover plate PCB with post hole, keep

handle upright, and screw yellow cover plate onto battery pack assembly.

C. Reinstall battery pack and modem end cap: Align D-shaped opening and pins on shaft. Lower battery pack into housing; push gently to mate.

Tighten captured screw to secure battery pack in housing. Remove water from O-rings and mating surfaces with lint-free cloth. Inspect O-

rings and mating surfaces for dirt, nicks, and cuts. Clean as necessary. Apply light coat of O-ring lubricant to O-ring and mating surfaces.

Plug Molex connector together. Fit end cap into housing. Reinstall 2 cap screws.

2. Double click on SeatermV2.exe. In Instruments menu, select SBE 37 IM. SeatermIM opens.

3. In Communications menu, select Configure. In dialog box. Input Comm port and baud rate. Set ID to Automatically get ID for

1 MicroCAT on line; set ID to Use fixed ID for multiple MicroCATs on line. Click OK.

4. SeatermIM automatically connects to MicroCAT. As it connects, it sends #iiGetHD and displays response, and then fills Send Commands

window with list of commands for your MicroCAT.

5. Ensure all data has been uploaded from memory, and then send #iiInitLogging to make entire memory available for recording.

If #iiInitLogging is not sent, data will be stored after last recorded sample.

6. Set Date and Time (#iiDateTime=).

7. Set up other parameters as desired — see Command Instructions and Command List.

Deployment

1. Attach MicroCAT to insulated

mooring cable with Sea-Bird

mounting brackets. MicroCAT is

intended for deployment with the

sensors at the top for proper

operation – see manual for details.

Install (optional) ICC on mooring

cable.

2. See MicroCAT manual for SIM

wiring and configuration; see IMM

manual for IMM wiring and

configuration.

Data Upload

1. Connect cable from MicroCAT to computer.

2. Double click on SeatermV2.exe. SeatermV2 opens; in Instruments menu, select SBE 37 IM. SeatermIM opens.

3. In Communications menu, select Configure. In dialog box, select Comm port and baud rate (factory set to 9600). Set ID to Automatically get ID

for 1 MicroCAT on line; set ID to Use fixed ID for multiple MicroCATs on line. Click OK.

4. SeatermIM automatically connects to MicroCAT. As it connects, it sends #iiGetHD and displays response, and then fills Send Commands

window with list of commands for your MicroCAT.

5. If sampling autonomously (logging), command MicroCAT to stop logging by sending #iiStop.

6. Click Upload menu to upload stored data.

7. SeatermIM prompts you to run SBE Data Processing to convert uploaded .hex file to .cnv file for use by other modules in data processing

software. Process file and review data to ensure all data has been uploaded.

Command Instructions

•Input commands in upper or lower case letters and register commands by pressing Enter key.

•MicroCAT sends an error message if invalid command is entered.

•If new command is not received within 2 minutes after completion of a command, MicroCAT returns to quiescent (sleep) state.

•If in quiescent (sleep) state, re-establish communications by selecting Connect in SeatermIM’s Communications menu.

SBE 37-IMP-ODO

Direct Connection

SBE 37-IMP-ODO

Connection with Inductive Cable Coupler (ICC)

SBE 37-IMP-ODO MicroCAT Recorder

(see User Manual for complete details)

Reference

Sheet

Release date 10

-28-15, Reference sheet version 007; Digital Firmware version 2.13.0 & later; IMM Firmware version 1.10 & later

Command List (commands most commonly used in field; see manual for complete list and detailed descriptions)

FUNCTION

CATEGORY

COMMAND

DESCRIPTION

SIM

Commands

Power-On

PwrOn

Send wakeup tone to all IMs.

PwrOff

Send power off command to all IMs. Logging and memory retention unaffected.

AutoPwrOn=x

x=Y: Send PwrOn to IMs when power applied to SIM. x=N: Do not.

Status

Display SIM firmware version and status.

Communications

Baud=x

x= baud from SIM to computer (1200, 2400, 4800, or 9600). Default 9600.

DataNNMax=x

x= timeout that applies to Dataii; default 1000 millisec.

RelayMax=x

x= timeout that applies to all other commands; default 20 sec.

EchoOn

Echo characters received from computer.

EchoOff

Do not echo characters received from computer.

MicroCAT

Integrated

IMM

Commands

(ii =

MicroCAT

ID)

See IMM

manual for

details

ID and

Group

Number

ID?

Get MicroCAT ID (0-99).

*ID=ii

Set ID to ii (ii=0-99). Only 1 MicroCAT can be on line. Must be sent twice.

!iiSetGroupNumber=x

Set MicroCAT group number (0–9). Group 0 pre-defined as all instruments with integrated IMM.

Status

!iiGetCD

Get integrated IMM configuration data.

!iiGetHD

Get integrated IMM hardware data.

!iiGetSD

Get integrated IMM status data.

Testing

!iiTestCableCoupler

Test integrity of integrated IMM. Line must be captured before command sent

Get Data

!iiSetGDataStr=x

x= character string to send to MicroCAT when GData is sent from surface IMM/SIM.

GData

Send string defined by !iiSetGDataStr=; hold response until!iiData, Dataii,or !iiGetReply sent.

!iiData,Dataii,or !iiGetReply

Get data obtained with GData from MicroCAT with ID=ii.

MicroCAT

Acquisition

Micro-

controller

Commands

(ii =

MicroCAT

ID)

Status

#iiGetCD (get configuration data), #iiGetSD (get status data), #iiGetCC (get calibration coefficients), #iiGetEC (get event counter

data), #iiResetEC (reset event counter), #iiGetHD (get hardware data), #iiDS (get status), #iiDC (get calibration coefficients)

General

Setup

#iiDateTime=mmddyyyyhhmmss

Set real-time clock month day year hour minute second.

#iiBaudRate=x

x= baud (4800, 9600, 19200, 38400, 57600, 115200) for Serial Mode (internal RS-232 connector).

#iiOutputExecutedTag=x

x=Y: Output XML Executed and Executing tags. x=N: Do not.

#iiReferencePressure=x

x= reference pressure (decibars) (for MicroCAT without pressure sensor).

Place MicroCAT in quiescent (sleep) state; for use in Serial mode only.

Pump

Setup

#iiMinCondFreq=x

x= minimum conductivity frequency (Hz) to enable pump turn-on.

#iiAdaptivePumpControl=x

x=Y: Use Adaptive Pump Control. x=N: Run pump for [#iiOxNTau * #iiOxTau20].

#iiOxNTau=x

x= pump time multiplier. Range 0 – 100.0;default 7.0.

#iiPumpOn #iiPumpOff

Turn pump on or off, for testing.

SBE 63 DO

Sensor Setup

#iiSend63=command

Command MicroCAT to send command to SBE 63 and receive response.

Other commands

Required: SetEcho=1, SetFormat=1, SetAvg=1 to 16 (recommend 2), SetAutoRun=0.

Memory

Setup

#iiInitLogging

Initialize logging, setting memory pointer to 0.

#iiSampleNumber=x

x= sample number for first sample when logging begins.

Output

Format

Setup

#iiOutputFormat=x

x=0: Output raw decimal data.

x=1: Output converted decimal data.

x=4: Output converted decimal data, alternate.

x=5: Output converted decimal data, compatible mode.

#iiOutputTemp=x

x=Y: Output temperature. x=N: Do not.

#iiSetTempUnits=x

x=0: Temperature °C, ITS-90. x=1: Temperature °F, ITS-90.

#iiOutputCond=x

x=Y: Output conductivity. x=N: Do not.

#iiSetCondUnits=x

Conductivity, specific conductivity units. x=0: S/m. x=1: mS/cm. x=2: µS/cm.

#iiOutputPress=x

x=Y: Output pressure. x=N: Do not.

#iiSetPressUnits=x

x=0: Pressure decibars. x=1: Pressure psi (gauge).

#iiOutputOx=x

x=Y: Output oxygen. x=N: Do not.

#iiSetOxUnits=x

x=0: Oxygen ml/L. x=1: Oxygen mg/L.

#iiOutputSal=x

x=Y: calculate and output salinity (psu). x=N: do not.

#iiOutputSV=x

x=Y: calculate and output sound velocity (m/s). x=N: do not.

#iiOutputSC=x

x=Y: calculate and output specific conductivity. x=N: do not.

#iiTxSampleNum=x

x=Y: Output sample number with data. x=N: Do not.

Autonomous

Sampling

(logging)

#iiSampleInterval=x

x= interval between samples (10 – 21,600 sec).

#iiStartNow

Start logging now. Data stored in FLASH memory.

#iiStartDateTime=mmddyyyyhhmmss

Delayed logging start: month day year hour minute second.

#iiStartLater

Start logging at delayed start time. Data stored in FLASH memory.

#iiStop

Stop logging or waiting to log.

Polled

Sampling

(data not stored

in FLASH

memory unless

noted; format

specified by

#iiOutput

Format=

unless noted)

#iiTS

(Do not run pump) Take sample, output data.

#iiTPS

Run pump, take sample, output data.

#iiTPSH

Run pump, take sample, do not output data.

#iiTPSS

Run pump, take sample, store in FLASH memory, output data.

#iiTSN:x

(Do not run pump) Take xsamples and output data.

#iiTPSN:x

Run pump continuously while taking xsamples, output data.

#iiT63

Do not pump. Take sample from SBE 63, output oxygen in format set by SetFormat= in SBE 63.

#iiSL

Output last sample.

#iiSLTP

Output data from last sample, then run pump and take new sample.

#iiSLTPR

Output raw data from last sample, then run pump and take new sample.

#iiDNx

Upload last xscans from memory; can send while logging

Data Upload

#iiGetSamples:b,e

Upload scan bto e, in #iiOutputFormat. Send #iiStop before sending.

#iiDDb,e

Upload scan bto e, converted decimal format Send #iiStop before sending.

Altri manuali SBE Registratore vocale

SBE

SBE 37-SMP-ODO Manuale utente

Manuali Registratore vocale popolari di altre marche

Sony

Sony ICD-UX533F Manuale utente

RCA

RCA VR5230 Manuale utente

Ramsey Electronics

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Guida utente

Sony

Sony TCM-400DV Manuale utente

LogTag

LogTag TREL30-16 Manuale utente

SVAT

SVAT CVP800 Manuale utente

Marantz

Marantz PMD620 Manuale utente

Zoom

Zoom H4next Manuale utente

Roland

Roland BR-900CD Manuale utente

JVC

JVC ProHD GY-HMZ1U Manuale operativo e di manutenzione

Panasonic

Panasonic PQT8531-P Manuale utente

Sanyo

Sanyo TRC-6400 Manuale utente

Tascam

Tascam DR-07 Manuale utente

Olympus

Olympus DW-90 Manuale utente

Sanyo

Sanyo ICR-B150 Manuale utente

Korg

Korg D4 Manuale utente

Sony

Sony ICD-SX46 - Ic Recorder Manuale utente

Olympus

Olympus DIGITAL VOICE RECORDER WS-200S Istruzioni per il montaggio