SC&T VKM03T Manuale utente

VGA & USB, AUDIO, RS232, IR CAT5 Extender

ITEM NO.: VKM03 VGA & USB with Stereo Audio, RS232, and IR CAT5 Extender

The VKM03 VGA, USB with Stereo Audio, RS232, and IR CAT5 extender design for extends all signals

over one CAT5 up to 140 meters, with local VGA monitor output. It provides superior video quality up

to 1920 x 1080 resolutions, and using cost effective Cat5e cable, instead of VGA, audio, RS232 cables,

for an easy, neater and reliable installation. Using a standard Gigabit Ethernet LAN system and add a

Gigabit switch could do multiple display. It is optimized for applications at digital signage, home

network integration, and industrial control, hospital, education, security, and KVM extension.

Features:

Extend VGA, stereo audio, RS232, IR and USB signals over one CAT5E/CAT6 cable.

USB port support USB 2.0, USB 1.0 & USB 1.1

Full Duplex data communication.

Transmitter unit built in VGA loop output.

Receiver unit with 4 ports USB devices, to extend USB 2.0 peripheral devices, such as flash disk,

hard disk, keyboard, mouse, etc.

Supports up to 1920 x 1080.

Transmission range up to 140 meters over CAT5e, 180M over CAT6.

Support point to point and point to multi-display connections via Gigabit network switch.

Plug and play for easy operation.

Perfect for control remote machines and security monitoring systems, digital signage application.

Optional model: SR01 signal repeater for longer distance application.

Panel View:

Transmitter

Receiver

Installation View:

Point to Point Direct Connection:

Over Gigabit Ethernet switches: One to Multiple Connection

1 Input to Multiple outputs connections via a Gigabit network switch

Recommend installation using an independent Gigabit LAN; do not link with existing LAN to

avoid a lot of video data transmission slow down your network system.

When using multiple transmitters and receivers via a Gigabit network switch, identically

configure dip switches on the local and remote units to link them together.

In multiple connections keyboard and mouse are plug and play, for other USB devices just

simply press and click the USB keyboard Pause/Break” KEY on a receiver for three times to

get USB control; only one unit can have USB control over the source at any time.

Optional Model: SR01 Signal Repeater (order separately)

Extend data signal for an additional 120meters.

Application for VKM03 signals for extra long range transmission.

Ability to cascade connection with multiple SR01 for long range transmission

Built in LED status indication.

External power required.

Plug and play for easy installation.

Work with VKM03 CAT5 Extender:

LED Indication Status:

Power On (power)

Link Flash (under linking)

On (linking)

RJ45 Green Flash (Data transmission)

Orange On (linking)

Cable:

Link Cable use high quality Cat.5e UTP/STP/FTP or Cat.6 UTP cable

Ethernet Switch Hub Recommendation：

Recommend to use IGMP and Jumbo Frame over 8K Ethernet Switch Hub in order to achieve the

best transmission quality

HOT KEY Function：

VKM03 could use Ethernet Switch Hub to do one to multiple application, Under multiple VKM03R

for switching VKM03R external host USB flash drive port, make the external flash drive you want

to use with an external USB keyboard, to click three times “Pause/Break” KEY, the system will

redetect and connect USB devices.

Caution：

1. VKM03 do not recommend working with general LAN connection to avoid large

video data transmission or multicast packets to slow down your other LAN devices.

2. IR receiving angle ±55degree, emitting angle 30degree，distance reach to 3-5

meters.

Web Setting Function：

There are three ways to get the IP address of receiver:

1. Connect monitor with receiver, local IP shows on right bottom screen when receiver booting or

transmitter not connected( or no video input)

2. Install Internet explorer plug-in: Bonjour , click device name to enter web setting page to get

the IP address(please refer Bonjour plug-in installation)

There are three ways to get the IP address of transmitter:

1. Connect monitor with receiver, connect receiver with transmitter and set in the same

channel, remote IP shows on right bottom screen when receiver booting or no video input from

transmitter

2. Install Internet explorer plug-in: Bonjour , click device name to enter web setting page to get

the IP address(please refer Bonjour plug-in installation)

System default IP setting is Auto IP, it will assign 169.254.X.X (subnet mask 255.255.0.0) to

transmitters and receivers, you could also set to DHCP or Static IP.

You computer must set in same subnet mask to enter the web setup page.

If you do not sure the IP address of transmitters/receivers you could reset the transmitters and

receiver to default by press the LINK button to power on (Press and hold until Green and Blue

LED Flash) to reset to default.

Bonjour plug-in installation:

1. Install BonjourSDKSetup.exe

2. Right click on “My Network Place” “Properties” then right click on “Local Area Connection”

“Properties” then double click on “Internet Protocol (TCP/IP)” to setting as below: (IP

address 169.254.111.111, sub mask 255.255.0.0)

3.Use CAT5 cable to connect transmitter RJ45 port to PC LAN port, open IE browser then

select View Explorer Bars Bonjour.

4. Double click on “HTTP on ast-gateway(VKM03T)” or “HTTP on ast-client (VKM03R)”, it will pop

up web setup in Bonjour windows as below:

5. Select Network page

IP Mode :Auto IP、DHCP、Static three modes, select one of them and press “Apply” to finish

setting.

Casting Mode : Multicast(one to multiple ) and Unicast(one to one) two modes ,select and

press “Apply” to finish setting ( If setup at Multicast, pick Auto select USB operation mode per

casting mode)

6. Function setup

VKM03T Video over IP: This function setup the video signals send from network, select and enter

“Apply” finish setting

VKM03R Video over IP : This function setup the video signals send from network, select Copy

EDID from this Video Output and enter “Apply” finish setting (pick up this item will auto copy

VKM03R TV EDID).

In multiple connections the EDID will copy from the last connected receiver.

USB over IP Setup: This function setup the USB signals send from network.

In Unicast (one to one) mode: Operation Mode selects “Active per request” and enters “Apply” to

finish setting.

In Multicast (one to multiple) mode: Operation Mode select “Auto select mode” and enter “Apply”

to finish setting.

Serial over IP: This function setup Serial (RS232) signal sends from network

[Baudrate Default：115200]

Operation Mode selects “Type 2 (Recommended. Dumb redirection.)” And enter Apply to

finish setting.

Baud rate Setting for Type 2 : It could change Baud rate as below : 300, 600, 1200, 2400,

4800, 9600, 14400, 19200, 38400, 57600, 115200, 230400

RJ45 Define:

Link Cable (TIA/EIA-568-B)

1. Orange-white Data 1 +

2. Orange Data 1 -

3. Green-white Data 2 +

4. Blue Data 3 +

5. Blue-white Data 3 -

6. Green Data 2 -

7. Brown-white Data 4 +

8. Brown Data 4 -

Package Include:

VKM03T Transmitter x 1

VKM03R Receiver x 1

3.5mm Audio cable 80cm x 1

VGA cable 90 cm x 1

IR emitter cable x 1

DC 5V 2Amp power adapter x 2

Specification:

ITEM NO. VKM03T VKM03R

Support Resolution Up to 1920 x 1080 @ 85 Hz

Transmission Distance CAT5e: 140M, CAT6: 180M (Max)

Video Input Signals RGB Analog (75Ω, 0.7Vp-p) Sync Signal H/V Separated (TTL)

VGA Connector DB15 Female x 2 DB15 Female x 1

USB Connector USB B-Type x 1

USB A-Type x 4

RS232 Connector DB9(Female) x 1

DB9(Male) x 1

Audio Connector 3.5 mm Phone Jack x1

IR Connector 3.5 mm Phone Jack x1

Built-in

Link Connector RJ45 x 1

Power Supply DC 5V 2 Amp

Power Consumption 1.1Amp

Temperature Operation: 0 to 55℃, Storage: -20 TO 85℃, Humidity: up to 95%

Dimensions mm 125 x 120.5 x 30

Weight g 335 330

Rev.D

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manuale utente