Schlage BE365 Manuale utente
Table of Contents
P515-549
FE575
FE595
BE365
Preset Codes
BE365 Features.......................................................2
Lock Operation ............................................2
Changing the Battery...................................3
FE575 Features.......................................................4
Lock Operation ............................................4
Changing the Battery...................................5
FE595 Features.......................................................6
Lock Operation ............................................6
Changing the Battery...................................7
Programming for All Models ....................................8
KeepingYour Lock Secure.....................................10
Key Override..........................................................10
Troubleshooting Guide...........................................11
Emergency Lock Override.....................................12
Place Label Here
Programming Code: 123456
User Code A: 4321
User Code B: 5678
S/N: 1-00000000
Model: BE365
Example
Example
Preset User Codes
BE365, FE575, FE595
Programming/Operating Guide
Preset Programming Code
Serial Number
Lock Series
2
BE365 Features
A. Button
1. Press to turn on backlight.
2. Press to clear an incorrect code entry.
B. Keypad
1. Use to unlock the lock by entering a
valid four-digit user code.
2. Use to program the lock.(See page 8.)
C. Key Override (See page 10.)
D. OutsideThumbturn
Freely rotates until deadbolt is activated.
Then thumbturn will extend or retract
deadbolt.
E. InsideThumbturn
Extends and retracts the deadbolt from
the inside.
A. Button
B. Keypad
C. Key Override
D. Outside Thumbturn
E. Inside Thumbturn
To Retract the Deadbolt
a. Enter a valid four-digit user code.
b. The button will flash green.
c. Rotate outside thumbturn within five
seconds to retract deadbolt.
To Extend the Deadbolt
a. Push button.
b. Rotate outside thumbturn while
button is lit to extend deadbolt.
BE365 Lock Operation
a
b
c
a
b
3
Unlocked -
No user code
required
for entry
Locked -
User code
required
for entry
Deadbolt
BE365 Changing the Battery
Reverse steps to assemble lock.
a
bc
d
BE365 Lock Operation Continued
Locked - Deadbolt Extended Unlocked - Deadbolt Retracted
For low battery indications, see page 11.
NOTE: Replace with premium 9V alkaline battery.
4
A. Button
1. Press to turn on backlight.
2. Press to clear an incorrect code entry.
B. Keypad
1. Use to unlock the lock by entering a
valid four-digit user code.
2. Use to program the lock.(See page 8.)
C. Key Override
(See page 10.)
D. Outside Knob/Lever
Always rotates. Only retracts latch when
lock is unlocked.
E. Inside Knob/Lever
Always rotates and retracts latch for
immediate exit.
FE575 Features
A. Button
B. Keypad
C. Key Override
D. Outside Knob/Lever
E. Inside Knob/Lever
To Unlock the Lock
a. Enter a valid four-digit user code.
(See note.)
b. The button will flash green.
c. Rotate outside knob/lever within
five seconds to open door.
d. After five seconds, the lock will
automatically relock.
NOTE: The lock has two unique
preset user codes that are printed on
the front page of this guide and back
of the keypad assembly.
FE575 Lock Operation
a
c
b
5
FE575 Changing the Battery
a
b
c
d
e
f
Reverse steps to assemble lock.
For low battery indications, see page 11.
NOTE: Replace with premium 9V alkaline battery.
6
A. Button
1. Press to turn on backlight.
2. Press to clear an incorrect code entry.
B. Keypad
1. Use to unlock the lock by entering a
valid four-digit user code.
2. Use to program the lock.(See page 8.)
C. Key Override
(See page 10.)
D. Thumbturn
Switches between locked and unlocked.
(See below.)
E. Outside Knob/Lever
Always rotates. Only retracts latch when
lock is unlocked.
F. Inside Knob/Lever
Always rotates and retracts latch for
immediate exit.
FE595 Features
A. Button
B. Keypad
C. Key Override
D. Thumbturn
E. Outside Knob/Lever
F. Inside Knob/Lever
Thumbturn in Locked Position Thumbturn in Unlocked Position
Unlocked -
No user code
required for
entry
Locked -
User code
required
for entry
FE595 Lock Operation
7
FE595 Changing the Battery
a
b
d
c
Reverse steps to assemble lock.
For low battery indications, see page 11.
NOTE: Replace with premium 9V alkaline battery.
a
c
b
To Unlock the Lock
(While thumbturn is in locked
position)
a. Enter a valid four-digit user code.
(See note.)
b. The button will flash green
c. Rotate outside knob/lever within five
seconds to open door.
d. After five seconds, the lock will
automatically relock.
NOTE: The lock has two unique preset
user codes that are printed on the
front of this guide and back of keypad
assembly.
FE595 Lock Operation Continued
8
Programming for All Models
Label is located on front of guide and back of keypad assembly.
Programming Code: 123456
User Code A: 4321
User Code B: 5678
S/N: 1-00000000
Model: BE365
Example
Example
Four-Digit User Codes
(4DUC)
• Activates lock
• Can be changed
• Up to 19 user codes
• Won't program lock
Six-Digit Programming Code
(6DUC)
• Programs lock
• Can be changed
• Won't operate lock
Schlage Button (on front of lock)
• Lights orange while in programming mode.
• Flashes green when programming is successful.
• Lights red when there is an error. Retry steps or see troubleshooting guide on page 11.
• Press to exit programming mode at any time.
• Wait until button stops flashing before entering additional codes.
Add a new user code
6DPC New 4DUC Reenter New 4DUC
Delete one existing or preset user code
6DPC Existing 4DUC Reenter Existing 4DUC
Change current or preset programming code
IMPORTANT: If you forget your new programming code, you will have to reset the lock.
6DPC New 6DPC Reenter New 6DPC
Enable/disable all user codes
1. Disable All User Codes: 6DPC
2. Enable All User Codes: 6DPC
Turn beeper on or off (preset is on)
NOTE: Lock will still beep when battery is low.
6DPC
Delete ALL user codes at once
IMPORTANT:This will delete all the user codes but not the programming code.
6DPC Reenter 6DPC
= Schlage Button
= Specific Number on Keypad
6DPC = Six-Digit Programming Code
4DUC = Four-Digit User Code
Legend
9
Enable/disableTurn Lock feature (BE365 ONLY) (preset is enabled)
NOTE:When Turn Lock feature is disabled, you must enter a valid user code to extend the
bolt.
6DPC
Create a temporary code (house sitter, plumber, etc.)
1. Add New User Code:
6DPC New 4DUC Reenter New 4DUC
2. Give person his/her code, but keep a written copy for yourself.
3. When code is no longer needed, delete User Code:
6DPC Existing 4DUC Reenter 4DUC
Delete a user code if user code is unknown
IMPORTANT:This will delete ALL the user codes but not the programming code.
1. Delete ALL User Codes:
6DPC Reenter 6DPC
2. Add New User Code:
6DPC New 4DUC Reenter New 4DUC
3. Repeat step 2 until all User Codes are reentered.
Ensure only you have codes to the lock
1. Change Programming Code:
6DPC New 6DPC Reenter New 6DPC
2. Delete ALL User Codes:
6DPC Reenter 6DPC
3. Add New User Code:
6DPC New 4DUC Reenter New 4DUC
Restore ALL preset lock settings
IMPORTANT: Lock will be reset to the preset programming and user codes.All existing
user codes and current programming code will be erased.
1. Disconnect the battery.
(For FE575, see page 3. For FE595, see page 5. For BE365, see page 7.)
2. Press and release .
3. Reconnect the battery and wait until is no longer lit.
4. Within 10 seconds, press and hold until lights green and the lock beeps.
10
SecurityTips
1. Do not share your programming code with other people.
2. Write down your programming and user codes and keep them in a safe place.
(Use the table below if desired.)
3. Give each person his/her own user code.You can have up to 19 user codes.
4. If you don't remember or don't know who has a user code, you can delete all the user
codes.(See page 8.)
Name User Code Name User Code Name User Code
KeepingYour Lock Secure
Key Override
Use key override to unlock the lock in the following situations:
1. Battery is dead.
2. No User Code is known.
FE575 and FE595
NOTE: Key does not retract latch.
BE365 Only
NOTE: Key will both extend and retract deadbolt.
270° 270°
Insert Key Rotate key
270° to unlock. Rotate knob/lever. Rotate key 270°
back to relock. When finished,
remove key.
Key cannot be
removed in this
position.
90°
90°
Rotate key 90°. Push key into
thumbturn. Rotate key and
thumbturn 90°.
Insert key.
Altri manuali per BE365
13
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Schlage Serratura della porta
Schlage
Schlage M400 Series Manuale utente
Schlage
Schlage AL-SERIES Manuale utente
Schlage
Schlage ALLEGION S-6000 Manuale utente
Schlage
Schlage B660 Manuale utente
Schlage
Schlage Touch FE695 Lever Manuale utente
Schlage
Schlage L9000 Series Manuale utente
Schlage
Schlage XE360-M Series Manuale utente
Schlage
Schlage Everest Manuale utente
Schlage
Schlage FE576 Manuale utente
Schlage
Schlage Omnia Manuale utente
Schlage
Schlage D170 Manuale utente
Schlage
Schlage P515-302 Manuale utente
Schlage
Schlage 7766 Manuale utente
Schlage
Schlage B560 Manuale utente
Schlage
Schlage Custom FC21 Manuale utente
Schlage
Schlage LE Manuale utente
Schlage
Schlage AD-200 Manuale utente
Schlage
Schlage SENSE Manuale utente
Schlage
Schlage CO-100 Manuale utente
Schlage
Schlage SENSE Manuale utente
