Schnick-Schnack-Systems DMX Pixel-Router Manuale utente
DMX Pixel-
Router
User Guide
--
© 2015 Schnick-Schnack-Systems GmbH
Version 2015: All technical data and the weight and dimension
information were carefully created – errors reserved. Any colour
deviations are printing-related.
We reserve the right to make changes that serve further impro-
vement.
Table of Contents
-R
Overview
Connectivity
Menu
Installation
System Cabling
To Access the Web Server
Web Server Settings
Homepage
Operation Mode
Short Name/Long Name
Output Ports
Log Files
Network Overview
Help/Contact
Technical Data
Pin Connection
Table Art-Net™ Universes -
--
Overview
The DMX Pixel-Router is a powerful and ecient Ethernet DMX converter that also
allows LED systems from third party providers to be controlled with Schnick-Schnack-
Systems proven technology.
With its video-to-LED enhanced processor, the DMX Pixel-Router far outpaces the
competition. It has an optimized, multi-tasking, real-time operating system to process
and transmit video data synchronously and with very low latency.
The DMX Pixel-Router is compatible with the protocols sACN and Art-Net™ by using the
Ethernet input. Schnicknet is of course also supported. The DMX Pixel-Router is one
of the few devices on the market that can process Ethernet bursts with more than 250
universes.
Because it uses the Generation 3 System Wide Sync from Schnick-Schnack-Systems, all
four DMX outputs are synchronized with the source. (Prerequisite: the source must also
use the System Wide Sync, for example the Pixel-Gate)
Optically isolated outputs provide an additional operational reliability, which is espe-
cially important for larger installations. Mounting takes place via a top-hat rail.
The Router can be completely congured remotely thanks to an integrated HTML 5.0
web server and out having to rely on additional soware.
Upon delivery, the Router is in Demo mode (consecutive color gradient) on all four
outputs.
-R
Connectivity
The following connectors are located on the unit:
pin assignment
DMX Out 1-4
GND
DATA -
DATA +
Out 1-4 DMX output
Ethernet Ethernet input
Power 24V connection
pin assignment
Power
GND
+24V Power 1
+24V Power 2 *
*Redundant power supply is optional for
increased operational reliability
--
Menu
The following LEDs are located on the front of the unit:
ID Lights up blue when the search/highlight function is
activated in the web server
Power Lights up red when hooked up to electricity
ETH Lights up green when a physical Ethernet connection
exists
Link Lights up yellow when data is being received
Out 1-4 Lights up green when a DMX signal for the
corresponding output is received and transmitted
Reset
To activate the Reset button, poke a thin object through the opening at the front. You
can re-start the unit by pressing the Reset button briefly. If you press the Reset button
longer than five seconds, the unit returns to the factory settings and re-starts (Power
LED blinks). When you press the Reset button longer than 15 seconds, the IP setting
also is re-set in addition to the factory settings (ID LED blinks) and the unit re-starts.
Third party products
or
Schnick-Schnack-Systems products
DMX Pixel-Router
Power supply
External
Signal input
Ethernet
DMX
Power supply
DMX Pixel-Router 24V
-
System Start-Up
Check the device for any damage incurred during transit immediately aer unpacking.
A damaged unit must not be put into operation.
If the DMX Pixel-Router has been taken from a cold environment into a warm interior
aer transportation, allow at least one hour for it to warm up before it is put into
operation. This allows possibly formed condensation to evaporate and therefore the
electronics are not endangered.When in operation, please make sure that the ventila-
tion slits are not covered up. The supply air temperature should not exceed 35°C.
Keep the unit out of direct sunlight at all times. Never clean the device with aggressive
cleaners. For cleaning purposes, the wiping of the device with a moist cloth is su-
cient. In the case of stubborn dirt, a mild cleaner can be used on the moistened cloth.
System Cabling
--
To Access the Web Server
Step 1
Connect the PC and the device with a network cable.
Step 2
Congure the network card for Art-Net™.
Caution: please note previous settings so they can
be entered again later.
Fuse
USB 1
out
USB 2
out
USB
in SD / mmc
Ethernet
Activity Link
DMX
Activity in
Fuse
Out 3Out 4
Fuse
Out 2
Fuse
Out 1
IP-adress 2.0.0.1
subnet mask 255.0.0.0
-
Step 3
Find the Router’s IP address on the back of the unit.
Step 4
Enter IP address in the browser.
Fuse
USB 1
out
USB 2
out
USB
in SD / mmc
Ethernet
Activity Link
DMX
Activity in
Fuse
Out 3Out 4
Fuse
Out 2
Fuse
Out 1
--
Web Server Settings
Homepage
This is where the basic data for the DMX Pixel-Router is display-
ed.
Highlight o/on: when switching to Highlight on, the blue
ID-LED lights up on the Router. With the help of the High-
light-Button, especially for larger installations, the device that
it’s being congured via the web server can be detect.
By clicking on “click to unlock” you can change the Operation
Mode as well as the name of the Power Supply.
Indice
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza