Schrack Technik USBB96A5D Manuale utente
BATTERY INSTALLATION MANUAL
Battery Box
Models: USBB96A5D USBB96M1D
USBB96M4D USBB180A3D USBB240A3D
Series GENIO Dual Power (USSD..)
2
Inhalt
BATTERIES INSTALLATION 3
TYPE OF BATTERIES REQUIRED 3
BATTERY BOX OPENING 4
BATTERY INSERTION 6
BATTERY BOX 96A5D (8 BATTERIES) 6
BATTERY BOX 96M1D/96M4D (8+8 BATTERIES CONNECTED IN PARALLEL) 8
BATTERY BOX 180A3 (15 BATTERIES) 10
BATTERY BOX 240A3D/240A5H (20 BATTERIES) 12
LABELING 14
BATTERY BOX 14
WIRING DIAGRAM 15
BATTERY BOX 96A5D (8 BATTERIES) 15
BATTERY BOX 96M1D/96M4D (8+8 BATTERIES) 16
BATTERY BOX 180A3D 17
BATTERY BOX 240A3D/A3H 18
TESTING 19
SAFETY TEST 19
3
BATTERIES INSTALLATION
This charter describes the procedure to be followed to install the batteries in the BATTERY BOX.
WARNING: in order to guarantee your safety and your product, please follow the instructions given below very
carefully.
MAKE SURE THAT THE BATTERY BOX IS DISCONNECTED FROM
THE UPS BEFORE PERFORMING THE FOLLOWING SEQUENCE OF
OPERATIONS
The Manufacturer shall not be held responsible for any damage caused by incorrect connections or by operations that are
not described in this manual
The electrical specifications of the BATTERY BOX are shown on the data plate attached to the rear of the apparatus.
TYPE OF BATTERIES REQUIRED
The BATTERY BOX has been designed to operate with the following types of batteries:
Models USBB96…-
•A5D / 9Ah Version: n° 8 batteries 12Vdc 9Ah
•M1D / 14Ah Version: n° 8+8 batteries 12Vdc 7Ah (connected in parallel)
•M4D / 18Ah Version: n° 8+8 batteries 12Vdc 9Ah (connected in parallel)
Models USBB180…-
•A3D / 7Ah Version: n° 15 batteries 12Vdc 7Ah
Models USBB240…-
•A3D / 7Ah Version: n° 20 batteries 12Vdc 7Ah
•A5H / 9Ah Version: n° 20 batteries 12Vdc 9Ah (only if the Battery Box is coupled with UPS)*
*in this case the UPS and the Battery Box have the same S/N
4
BATTERY BOX OPENING
1. Open the package and place the BATTERY BOX on a horizontal plane.
2. Unhook the plastic front panel and remove the screw of the top cover.
3. Remove the 4 fixing screws of the top cover in the rear panel of the Battery Box.
4. Remove the 11 fixing screws of the top cover in the sides of the Battery Box.
5. Push the cover toward the back of the Battery Box and remove it.
5
6. Remove the two plastic shells marked with the code.
6
BATTERY INSERTION
BATTERY BOX 96A5D (8 BATTERIES)
1. Apply the adhesive foam on each side (left and right) of the 5 batteries that will installed in the central raws.
2. Place the batteries on the plastic housings as shown in the picture below.
3. Place the separating sheets as shown in the picture below.
4. Using the supplied wirings, connect the batteries following the wiring diagram in this manual.
5. Taking care to place the wiring in an orderly way, place the plastic shells to complete the battery packs.
ADHESIVE
FOAM
ADHESIVE
FOAM
ADHESIVE
FOAM
PLASTIC
SEPARATOR
DUMMY
BATTERY
7
6. Replace the cover of the Battery Box and secure it with the screws.
7. Polarize the battery expansion sockets placed on the rear part of the battery box. Remove the indicated pin
from the socket following the instruction in the diagram below.
➔
8. Polarize the plugs of the battery expansion cable provided with the battery box. Insert no. 1 plastic pin
(accessory of the battery box) in the indicated hole following the instruction in the diagram below.
➔
8
BATTERY BOX 96M1D/96M4D (8+8 BATTERIES CONNECTED IN PARALLEL)
1. Apply the adhesive foam on each side (left and right) of the 5 batteries that will installed in the central raws.
2. Place the batteries on the plastic housings as shown in the picture below.
3. Place the separating sheets as shown in the picture below.
4. Using the supplied wirings, connect the batteries following the wiring diagram in this manual.
5. Taking care to place the wiring in an orderly way, place the plastic shells to complete the battery packs.
6. Replace the cover of the Battery Box and secure it with the screws.
ADHESIVE
FOAM
ADHESIVE
FOAM
ADHESIVE
FOAM
PLASTIC
SEPARATOR
DUMMY
BATTERY
ADHESIVE
FOAM
DUMMY
BATTERY
9
7. Polarize the battery expansion sockets placed on the rear part of the battery box. Remove the indicated pin
from the socket following the instruction in the diagram below.
➔
8. Polarize the plugs of the battery expansion cable provided with the battery box. Insert no. 1 plastic pin
(accessory of the battery box) in the indicated hole following the instruction in the diagram below.
➔
10
BATTERY BOX 180A3 (15 BATTERIES)
1. Apply the adhesive foam on each side (left and right) of the 5 batteries that will installed in the central raws.
2. Place the batteries on the plastic housings as shown in the picture below.
3. Place the separating sheets as shown in the picture below.
4. Using the supplied wirings, connect the batteries following the wiring diagram in this manual.
5. Taking care to place the wiring in an orderly way, place the plastic shells to complete the battery packs.
6. Replace the cover of the Battery Box and secure it with the screws.
ADHESIVE
FOAM
ADHESIVE
FOAM
PLASTIC
SEPARATOR
ADHESIVE
FOAM
ADHESIVE
FOAM
Questo manuale è adatto per i seguenti modelli
4
Altri manuali Schrack Technik Accessori per fotocamere
