SCHUNK OPS Series Istruzioni utente
Translation of the original manual
Assembly and Operating manual
OPS
Collision and Overload Protection
Imprint
2
02.00 | OPS | Assembly and Operating manual | en | 389668
Imprint
Copyright:
This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights
reserved. Any reproduction, processing, distribution (making available to third parties),
translation or other usage - even excerpts - of the manual is especially prohibited and
requires our written approval.
Technical changes:
We reserve the right to make alterations for the purpose of technical improvement.
Document number: 389668
Version: 02.00|22/03/2019|en
© SCHUNK GmbH & Co. KG
All rights reserved.
Dear Customer,
thank you for trusting our products and our family-owned company, the leading
technology supplier of robots and production machines.
Our team is always available to answer any questions on this product and other solutions.
Ask us questions and challenge us. We will find a solution!
Best regards,
Your SCHUNK team
SCHUNK GmbH & Co. KG
Spann- und Greiftechnik
Bahnhofstr. 106 – 134
D-74348 Lauffen/Neckar
Tel. +49-7133-103-0
Fax +49-7133-103-2399
schunk.com
Table of contents
02.00 | OPS | Assembly and Operating manual | en | 389668
3
Table of contents
1 General.................................................................................................................... 5
1.1 About this manual ................................................................................................ 5
1.1.1 Presentation of Warning Labels ...............................................................5
1.1.2 Definition of Terms...................................................................................6
1.1.3 Applicable documents ..............................................................................6
1.1.4 Sizes ..........................................................................................................6
1.2 Warranty .............................................................................................................. 6
1.3 Scope of delivery .................................................................................................. 7
1.3.1 Enclosed pack ...........................................................................................7
2 Basic safety notes ................................................................................................... 8
2.1 Intended use......................................................................................................... 8
2.2 Not intended use.................................................................................................. 8
2.3 Constructional changes ........................................................................................ 8
2.4 Spare parts ........................................................................................................... 8
2.5 Ambient conditions and operating conditions .....................................................9
2.6 Product safety ...................................................................................................... 9
2.6.1 Protective equipment...............................................................................9
2.6.2 Constructional changes, attachments, or modifications ..........................9
2.7 Personnel qualification....................................................................................... 10
2.8 Personal protective equipment.......................................................................... 11
2.9 Notes on safe operation .....................................................................................11
2.10 Transport ............................................................................................................ 12
2.11 Malfunctions....................................................................................................... 12
2.12 Disposal .............................................................................................................. 12
2.13 Notes on particular risks..................................................................................... 13
3 Technical Data ........................................................................................................14
4 Assembly ................................................................................................................15
4.1 Mechanical connection ...................................................................................... 15
4.2 Electrical connection .......................................................................................... 18
4.2.1 Sensor PNP-Version (standard) ..............................................................18
4.2.2 Sensor NPN-Version (special) .................................................................20
4.3 Air connections................................................................................................... 21
4.3.1 Module OPS 80-100................................................................................21
4.3.2 Module OPS 160-300..............................................................................21
4.3.3 Maximum operating pressure ................................................................21
4.4 How to dertermine the operating pressure ....................................................... 22
4.4.1 Calculation of the input air pressure (P).................................................22
Table of contents
4
02.00 | OPS | Assembly and Operating manual | en | 389668
5 Troubleshooting .....................................................................................................26
5.1 OPS does not react? ........................................................................................... 26
5.2 OPS does not lock? ............................................................................................. 26
5.3 No electrical signal?............................................................................................ 26
6 Maintenance ..........................................................................................................27
General
02.00 | OPS | Assembly and Operating manual | en | 389668
5
1 General
1.1 About this manual
This manual contains important information for a safe and
appropriate use of the product.
This manual is an integral part of the product and must be kept
accessible for the personnel at all times.
Before starting work, the personnel must have read and
understood this operating manual. Prerequisite for safe working is
the observance of all safety instructions in this manual.
Illustrations in this manual are provided for basic understanding
and may differ from the actual product design.
In addition to these instructions, the documents listed under
Applicable documents [}6] are applicable.
1.1.1 Presentation of Warning Labels
To make risks clear, the following signal words and symbols are
used for safety notes.
DANGER
Danger for persons!
Non-observance will inevitably cause irreversible injury or death.
WARNING
Dangers for persons!
Non-observance can lead to irreversible injury and even death.
CAUTION
Dangers for persons!
Non-observance can cause minor injuries.
NOTICE
Material damage!
Information about avoiding material damage.
General
6
02.00 | OPS | Assembly and Operating manual | en | 389668
1.1.2 Definition of Terms
The term "product" replaces the product name on the title page in
this manual.
1.1.3 Applicable documents
• General terms of business*
• Catalog data sheet of the purchased product *
The documents marked with an asterisk (*) can be downloaded on
our homepage schunk.com
1.1.4 Sizes
This operating manual applies to the following sizes:
• OPS 80
• OPS 100
• OPS 160
• OPS 200
• OPS 300 (special)
1.2 Warranty
If the product is used as intended, the warranty is valid for 24
months from the ex-works delivery date under the following
conditions:
• Observe the applicable documents, Applicable documents
[}6]
• Observe the ambient conditions and operating conditions,
Ambient conditions and operating conditions [}9]
General
02.00 | OPS | Assembly and Operating manual | en | 389668
7
1.3 Scope of delivery
The scope of delivery includes
• Collision and Overload Protection OPS in the version ordered
• Assembly and Operating Manual
• Accessory pack
1.3.1 Enclosed pack
Content of the accessories pack:
• 1 x Swiveling connection
• 1 x cable for sensors, ID number: 0301502
• Cylinder pin for mounting
• Screws for mounting
ID.-No. of the accessory pack
Accessory pack for ID number
OPS 80 5510476
OPS 100 5511310
OPS 160 5511335
OPS 200 5510618
OPS 300 5511076
Basic safety notes
8
02.00 | OPS | Assembly and Operating manual | en | 389668
2 Basic safety notes
2.1 Intended use
The Kollision- and Overload Protection OPS was designed as a
device to protect robots and handling unit from damage resulting
from collisions and overload conditions.
• The product may only be used within the scope of its technical
data, Technical Data [}14].
• When implementing and operating components in safety-
related parts of the control systems, the basic safety principles
in accordance with DIN EN ISO 13849-2 apply. The proven safety
principles in accordance with DIN EN ISO 13849-2 also apply to
categories 1, 2, 3 and 4.
• The product is intended for industrial and industry-oriented use.
• The product is intended for installation in a machine/system.
The applicable guidelines must be observed and complied with.
• Appropriate use of the product includes compliance with all
instructions in this manual.
2.2 Not intended use
It is not intended use if the product is used, for example, as a
pressing tool, stamping tool, lifting gear, guide for tools, cutting
tool, clamping device or a drilling tool.
• Any utilization that exceeds or differs from the appropriate use
is regarded as misuse.
2.3 Constructional changes
Implementation of structural changes
By conversions, changes, and reworking, e.g. additional threads,
holes, or safety devices can impair the functioning or safety of the
product or damage it.
• Structural changes should only be made with the written
approval of SCHUNK.
2.4 Spare parts
Use of unauthorized spare parts
Using unauthorized spare parts can endanger personnel and
damage the product or cause it to malfunction.
• Use only original spare parts or spares authorized by SCHUNK.
Basic safety notes
02.00 | OPS | Assembly and Operating manual | en | 389668
9
2.5 Ambient conditions and operating conditions
Required ambient conditions and operating conditions
Incorrect ambient and operating conditions can make the product
unsafe, leading to the risk of serious injuries, considerable material
damage and/or a significant reduction to the product's life span.
• Make sure that the product is used only in the context of its
defined application parameters, Technical Data [}14].
• Make sure that the product is a sufficient size for the
application.
• Make sure that the environment is free from splash water and
vapors as well as from abrasion or processing dust. Exceptions
are products that are designed especially for contaminated
environments.
2.6 Product safety
Dangers arise from the product, if:
• the product is not used in accordance with its intended
purpose.
• the product is not installed or maintained properly.
• the safety and installation notes are not observed.
Avoid any manner of working that may interfere with the function
and operational safety of the product.
Wear protective equipment.
NOTE
More information is contained in the relevant chapters.
2.6.1 Protective equipment
Provide protective equipment per EC Machinery Directive.
2.6.2 Constructional changes, attachments, or modifications
Additional drill holes, threads, or attachments that are not offered
as accessories by SCHUNK may be attached only with permission
from SCHUNK.
Basic safety notes
10
02.00 | OPS | Assembly and Operating manual | en | 389668
2.7 Personnel qualification
Inadequate qualifications of the personnel
If the personnel working with the product is not sufficiently
qualified, the result may be serious injuries and significant
property damage.
• All work may only be performed by qualified personnel.
• Before working with the product, the personnel must have read
and understood the complete assembly and operating manual.
• Observe the national safety regulations and rules and general
safety instructions.
The following personal qualifications are necessary for the various
activities related to the product:
Trained electrician Due to their technical training, knowledge and experience, trained
electricians are able to work on electrical systems, recognize and
avoid possible dangers and know the relevant standards and
regulations.
Qualified personnel Due to its technical training, knowledge and experience, qualified
personnel is able to perform the delegated tasks, recognize and
avoid possible dangers and knows the relevant standards and
regulations.
Instructed person Instructed persons were instructed by the operator about the
delegated tasks and possible dangers due to improper behaviour.
Service personnel of
the manufacturer
Due to its technical training, knowledge and experience, service
personnel of the manufacturer is able to perform the delegated
tasks and to recognize and avoid possible dangers.
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali SCHUNK Dispositivo di protezione
