Scilogex SCI-O330-Pro Manuale utente

SCI-O330-Pro & SCI-L330-Pro Orbital and Linear Digital Shaker

SCI-O180- Pro & SCI-L180-Pro Orbital and Linear Digital Shaker

Linear Digital shaker(7.5Kg)

Orbital Digital shaker(7.5Kg)

Linear Digital shaker(2.5Kg)

Orbital Digital shaker(2.5Kg)

SCI-L330-Pro

SCI-O330-Pro

SCI-L180-Pro

SCI-O180-Pro

Please read the User Manual and the related Video of this

instrument on our website carefully before use, and follow

all operating and safety instructions!

The website www.scilogex.com

User Manual

Cat No.12300140

Contents

Contents Inside front cover

Preface 1

Service 1

Warranty 1

1.Safety Instructions 2

2.Proper Use 3

3.Inspection 3

3.1 Receiving Inspection 3

3.2 Listing of Items 3

4. Trial Run 3

5.Control and Set 4

5.1 Control 4

5.2 Set 5

5.2.1 Set Time 5

5.2.2 Setting Speed 5

6.Operating Modes 6

6.1 Mode A 6

6.2 Mode B 7

6.3 Switching the Mode 7

6.4 Switch the shaking direction 8

7.Supported Load 8

8.Faults 8

9.Interface 8

10.Maintenance and Cleaning 9

11.Associated Standards and Regulations 9

12.Technical Data 10

13.Products and Accessories 10

Preface

Welcome to the“Orbital and Linear Digital Shaker User

Manual”.Users should read this manual carefully, follow

the instructions and procedures, and beware of all the

cautions when using this instrument.

Service

When help needed, you can always contact manufacturer for

technical support in the following ways:

SCILOGEX, LLC

1275 Cromwell Ave

Suite C6

Rocky Hill, CT 06067

USA

Tel：1- (860) 436-9221

Fax：1- (860) 436-9745

[email protected]

www.scilogex.com

Please provide the customer care representative with the

following information:

•Serial Number（on the rear panel）

•Description of problem (i.e., hardware or software)

•Methods and procedures adopted to resolve the problems

•Your contact information

Warranty

You have purchased a Scilogex instrument. This instrument

is warranted to be free from defects in materials and

workmanship under normal use and service, for a period

of 24 months from the date of invoice. The warranty is

extended only to the original purchaser. It shall not apply to

any product or parts which have been damaged on account

of improper installation, improper connections, misuse,

accident or abnormal conditions of operation.

For claims under the warranty please contact your local

dealer. You may also send the instrument direct to our works,

enclosing the invoice copy and by giving reasons for the

claim. You would be solely liable for freight costs.

1.Safety Instructions

Warning!

•Read the operating instructions completely

before use and follow the safety instructions.

•Ensure that only trained staff work with the

instrument.

Protective ground contact！

•Make sure the socket must be earthed

(protective ground contact) before use.

•Wear the personal protective equipment in accordance

with the hazard category of the media to be processed.

- Splashing of liquids.

- vibration force led to broken glass container.

- The body，hair，clothes，jewelry are inhaled.

•Use the instrument following the safety instructions and

profession safety rules to avoid any accident.

•Users are not allowed to touch moving parts of the

instrument to avoid any accidents. Pay attention to protect

hands or fingers from rolling when moving the instrument.

•Set up the instrument in a spacious area on an stable,

clean, non-slip, dry and fireproof surface. Do not operate

the instrument in explosive atmospheres, with hazardous

substances or under water.

•Observe the vessel on the shaking table for medium

splashing out of liquid when setting the motor speed. Reduce

the motor speed if the instrument is not running smoothly.

•Accessories must be securely attached to the instrument

so that it cannot come off by itselves, and vessels must be

firmly placed on the shaking table to avoid any injury.

•Working with combustible media or flammable materials

may result in additional hazards. Only process media that

will not react dangerously to the extra energy produced

through processing should be used on the instrument.

•Safe operation is only guaranteed with the accessories

described in the “Accessories”chapter and by following

the operating instructions in full. Always disconnect the

plug before fitting accessories. Check the instrument and

accessories beforehand for damage each time you use them.

Do not use damaged components.

•The instrument may only be opened by trained technicians.

And always disconnect the plug beforehand.

•The operating voltage required as stated on the instrument

and voltage in the supply network must match.

•Do not cover the instrument. Protect the instrument and

accessories from bumps and impacts.

•Keep away from high magnetic field.

SK-O（L）330- Pro Orbital and Linear Digital Shaker SK-O（L）180- Pro Orbital and Linear Digital Shaker

2.Proper use

The instrument is designed for mixing or shaking liquids in

schools, laboratories or factories. SK-330/180-Pro is suitable

for usage in various attachments for mixing liquids in

bottles, flasks, test tubes for a maximum supported weight of

7.5 kg(330)and 2.5Kg(180). This instrument is not suitable

for use in residential areas or other areas that may cause

danger to the user or instrument as mentioned in chapter 1.

3.Inspection

3.1 Receiving Inspection

Unpack the instrument carefully and check for any damages

which may have arisen during transport. If it happens, please

contact manufacturer for technical support.

Note:

If there is any apparent damage to the system,

please do not plug it into the power line.

3.2 Listing of Items

The packing includes the following items:

Items Qty

Main unit 1

Power cable 1

User manual 1

Table 1

4. Trial run

Do trial operation as follows:

•Make sure the required operating voltage and power

supply voltage match.

•Ensure the socket is securely earthed.

•Plug in the power cable，Power ON the instrument.

•LCD displays the safe rotary speed limit.

•LCD displays operating mode.

•Turn the speed knob to set the rated rotary speed

•Press the speed knob. And the shaking function is switched

ON.

•Press the motor regulation knob again. and the shaking

function is switched OFF.

If these operations above are normal, the instrument is ready

to operate following the “operation”chapter. If these

operations are not normal, the instrument may be in security

protection state or be damaged.

SK-O（L）330- Pro Orbital and Linear Digital Shaker SK-O（L）180- Pro Orbital and Linear Digital Shaker

If the mounting surface is not even, you can improve the

stability of the instrument with the adjustable feet. To do

this, turn the appropriate foot downward with the wrench

until the instrument is standing securely on the surface.

Figure 1

5.Control and Set

5.1 Control

Shaking table

Time knob

LCD time

LCD speed

Figure 2

Items Descriptions

Speed knob

Set the rated rotary speed. “rotation”

is switched ON or OFF via pressing the

knob.

Time knob

Set working time . “rotation”is

switched ON or OFF via pressing the

knob

LCD Display the status of instrument and any

set

Mains switch Switch ON or OFF.

Table 2

SK-O（L）330- Pro Orbital and Linear Digital Shaker SK-O（L）180- Pro Orbital and Linear Digital Shaker

•Put the instrument on stable and safe place and plug in the

mains power.

•Turn ON the mains switch on the left panel.

•The instrument starts self-test.

•The instrument shows rated speed and time after

initialization.

•Turn the speed knob on the left side to set the rated speed.

•Press the speed knob and characters on the left LCD do

not flash any more, and the shaking function is switched ON.

•Press the speed knob again and characters on the left LCD

begin to flash, and the shaking function is switched OFF.

•Turn the time knob on the left side to set the rated time

•Press the time knob and characters on the LCD do not

flash any more, and the timing function is switched ON.

•Press the time knob again and characters on the right LCD

begin to flash, and the timing function is switched OFF.

5.2 Set

5.2.1 Set time

The rated shaking time can be set by turning the time knob

on the right. A distinction is made for the shaking time

setting between timed mode and continuous operation. If

continuous mode is selected, the shake can continue its

shaking function for any amount of time with the previously

set speed. If timed mode is selected, the shaker can run in the

set time. After the instrument is powered OFF and restarted,

the set time is erased to zero blanking and it switches into

offline operating mode.

If a target time (max. 19h 59min) and speed are set, users

can activate the instrument with pressing the time knob，

and the time begin to read,If:

A，pressing the time knob，the speed and the time

will stop. Pressing the time knob again,restart the shake

function,the time will use the pre-set time

B，pressing the speed knob，the speed and the time

will stop; Pressing the time knob again,restart the shake

function,the time not(There are flashing on the righe of

the LCD )，pressing the time knob again restart the time

function. The time will use the pre-set time.

Note:

The current set time can be varied at any time.

5.2.2 Setting Speed

The rated speed and upper speed limit can be set by turning

the speed knob (As the Figure 6) . The continuous mode can

be switched ON with pressing the left knob without the time

setting and switched OFF with pressing the knob again..

Adjust the motor speed knob slowly in order to keep the

instrument running smoothly.

Note:

The current set speed can be varied at any time.

6.Operating modes

6.1 Mode A

Operating mode A is the default mode set in factory. After

turning ON the instrument with the mains switch, the

shaking and timing functions are turned OFF. The LCD

displays the set time and speed values. They are adopted or

varied when the corresponding functions are turned ON.

After turning ON the instrument, the following process will

be shown on the display.

•The left LCD displays “SAF”and the right displays the

upper speed limit( rpm）which can be set by pressing the

speed knob and turning at the same time.

Figure 3

•The LCD displays run modes “StA”、“A”or “B”

for about 2 seconds.

Figure 4

•The set or stored speed value is shown in the left display, and

the set or stored time value is shown in the right display. Turn

the speed knob and time knob can set the speed and time.

Figure 5

•After pressing the speed knob or time knob, the instrument

begins to run at the set speed. The actual speed and time

remaining are shown in the LCD. If the remaining has

reached zero, the shaker stops its motion. Pressing the

speed knob alone,the instrument will work at continuous

mode(The time function is OFF)

Figure 6

Note:

The set values can be varied during shaking.

Shaking can be stopped by pressing the left or

right knob.

6.2 Mode B

When the instrument is turned ON and values for speed

and time are erased to zero, users can set. The upper speed

limit that has been set is taken over from operating mode

A and cannot be modified. After the power has been turned

OFF, the instrument will no longer automatically start up in

operating Mode B by itself.

After turning ON the instrument and selected run mode, the

following process will be shown on the display.

•The left LCD displays “SAF”and the right displays the

upper speed limit( rpm）which cannot be changed.

Figure 7

•The LCD displays run modes “StA”for about 2

seconds.

Figure 8

•The set speed value is shown in the left display, and the set

time value is shown in the right display. Then set the motor

rotary speed and time.

Figure 9

Figure 10

•After pressing the speed knob or time knob, the instrument

begins to run at the set speed. The actual speed and time

remaining are shown in the LCD. If the remaining has

reached zero, the shaker stops its motion.

Figure 11

Note:

The set values can be varied during shaking.

Shaking can be stopped by pressing the left or

right knob.

6.3 Switching the mode

Switch the operating mode as follows:

•Turn OFF the instrument with the mains switch.

•Hold down both knobs and turn ON the instrument with

the mains switch. After about 5 second, you can let go of the

knobs.

•Switch between operating Modes A and B in order.

6.4 Switch the shaking direction

Change the shaking direction according to the steps as

follows:

•Turn OFF the instrument;

•Press and hold time knob, at the same time turn on the

instrument, release the time knob after 10 seconds;

•Switch the operation direction in turn.

7.Supported load

In order to ensure safe, the shaker must only be operated

within the supported weight (7.5kg for 330 and 2.5Kg for

180).

Make sure the holding surface of the shaker is always clean

and level. Ensure the individual shaking vessels must be

placed evenly and fastened securely in the middle of the

shaking table no matter one or multiple shaking vessels are

placed.

8.Faults

•When switched ON, the instrument doesn’t work

■Check whether the power cable fitted well

■Check whether the fuse is broken

•The speed cannot reach set value

■Check whether it is overloaded

•The motor does not start via pressing the speed knob and

time knob

■Check whether the time is set to zero

9.Interface

SK-O330(180)-Pro/ SK-L330(180)-Pro Orbital and Linear

Digital Shaker, special adapter and cable are used to link to

external device.and the Standard 9-pin interface to connect

with the PC.

•The cable between the shaker and the computer used EIA

Standard RS232C communication line，corresponding to

the DIN 66020 interface.

•Transmission method: Asynchronous signal transmission.

•Mode of transmission: Fully Duplex.

•1 start bit; 8 character bits; 1 stop bit.

•Transmission speed: 9600 bit/s

Note：

Forbid to plug in and plug off the power cable

when the instrument working

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Scilogex Spruzzatore di vernice

Scilogex

Scilogex SK-L330-Pro Manuale utente

Manuali Spruzzatore di vernice popolari di altre marche

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuale utente

Graco

Graco 246737 Manuale per l'uso e la cura

Binks

Binks SV100 Manuale utente

Fimco

Fimco LG-4-3-1 Manuale utente

AG SPRAY

AG SPRAY FS-ATV-25BL Manuale utente

Nordson

Nordson MicroMax 2 Manuale utente

Bonide

Bonide 051 Manuale operativo

zogics

zogics Z-DAS Manuale utente

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuale utente

Matrix

Matrix SG 650 Manuale utente

Anest Iwata

Anest Iwata SGA-3 Guida rapida

paasche

paasche VV Scheda tecnica

Carlisle

Carlisle DeVilbiss JGA-510 Manuale utente

Gardena

Gardena 11120 Manuale utente

Conrad

Conrad Hobby Airbrush K3 Manuale utente

wiwa

wiwa 14025 R/F Manuale utente

Graco

Graco EM 390 Manuale operativo

DeVilbiss

DeVilbiss LUNA2i Manuale utente