Scion PT398-52122 Manuale utente
SCION xD 2012 - TVIP V5
Preparation SCION SECURITY
Page 1 of 23 pages
Issue: A 10/18/11
Part Number: PT398-52122
Conflicts
Do not install into vehicles without RKE, or with
Factory Alarm System.
Recommended Sequence of Application
Item # Accessory
1 Navigation
2 V4
3 V5
Kit Contents
Item # Quantity Description
1 1 Wire Harness
Hardware Bag Contents
Item # Quantity Description
1 1 GBS ECU
2 1 V5 ECU
3 1 Status Monitor w/Microphone
4 4 Foam Tape
5 35 Wire Ties
6 2 Window Warning Label
7 1 Owner’s Manual
8 1 Warranty Card
9 8 Butyl
10 2 Large Foam Tape (1= 2 pieces)
Additional Items Required For Installation
Item # Quantity Description
Recommended Tools
Personal & Vehicle
Protection Notes
Safety Glasses
Safety Gloves (Optional)
Vehicle Protection Blankets, Parts Boxes
Special Tools Notes
Striker Tool CAD-E IADS ALL 02-016-01
Installation Tools Notes
Phillips Screwdriver #2 screwdriver or tip
Flat Blade Screwdriver Jeweler’s screwdriver
Nylon Panel Removal
Tool e.g. Panel Pry Tool #1 Toyota
SST # 00002-06001-01
Side Cutters
Torque Wrench 36 in•lbf (4.07 N•m)
Utility Knife
Tape Clear
Socket 10mm, Extension
Special Chemicals Notes
Cleaner VDC Approved Cleaner
Glass Cleaner Household Glass Cleaner
Legend
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
• Safety (eye protection, rechecking torque procedure, etc.)
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)
Please see your Scion dealer for a copy of this document
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
SAFETY TORQUE: This mark indicates that torque is
related to safet
y
.
SCION xD 2012 - TVIP V5
Preparation SCION SECURITY
Page 2 of 23 pages
Issue: A 10/18/11
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 3 of 23 pages
Issue: A 10/18/11
A. Vehicle Disassembly
1. Vehicles with Automatic Transmission
should be placed in Park and have
the Parking brake set before
disconnecting the Battery.
2. Remove the Negative battery cable.
(a) Note the battery cable position,
as it will be reinstalled in the
same position
DO NOT TOUCH THE POSITIVE
BATTERY TERMINAL.
10mm Socket
Fig. A-1
Fig. A-2
Remove all corresponding
connectors accordingly as you
disassemble.
Overview of Vehicle Disassembly
Glove box
Floor console
Lower center
console
p
anel
Passenger side
under cover
Steering wheel
column cover
Lower dash
cover
Metal brace
Driver side under
cover
Storage
box
Upper center
console
p
anel
Stick shift
knob
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 4 of 23 pages
Issue: A 10/18/11
3. Disconnect the Dampener from the
glove box.
4. Remove the Glove box.
5. Remove the passenger side Under
cover.
6. Unscrew the Stick shift knob,
and remove the Upper center console
panel.
7. Unscrew the Stick shift knob,
and remove the Upper center console
panel.
Fig. A-3
Fig. A-4
Fig. A-5
Automatic Transmission vehicle
Manual Transmission vehicle
Nylon Panel Removal Tool
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 5 of 23 pages
Issue: A 10/18/11
8. Remove 3 bolts.
9. Remove the Floor console.
10. Remove 2 bolts and remove the
Lower center console panel.
11. Remove the Storage box in Driver’s
side.
Fig. A-8
Nylon Panel Removal Tool
Fig. A-6
10mm Socket
Fig. A-7
10mm Socket
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 6 of 23 pages
Issue: A 10/18/11
12. Open and release clips.
13. Remove 2 Screws.
14. Remove the Lower dash cover.
15. Remove 2 bolts and the metal brace.
Fig. A-10
Fig. A-9
Screw driver
Fig. A-11
10mm Socket
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 7 of 23 pages
Issue: A 10/18/11
16. Remove 2 Screws and the driver side
Under cover.
17. Insert the key into ignition switch and
turn it to On.
18. Gain access to the 2 screws securing
the steering column cover, and
Remove them.
19. Remove 1 Screw.
20. Remove the Steering column cover.
Fig. A-14
Screw driver
Fig. A-13
Screw driver
Fig. A-12
Screw driver
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 8 of 23 pages
Issue: A 10/18/11
B. Wire Harness Installation
(Driver’s Side)
1. Route the V5 Harness through Center
console.
(a) Harness with ECU
connectors:route to passenger
side.
(b) Harness with Status Monitor:
route down towards floor console.
2. Secure the V5 Harness’s White Tape
Marker to the vehicle harness with
1 Wire Tie.
“Wire To Wire” is a process of
inserting TVIP connectors between
vehicle connectors in order to obtain
appropriate electronic signals.
It will be repeated throughout
installation.
Fig.B-2
Side Cutter
Fig. B-3
Fig.B-1
Status Monitor
ECU
Connector
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 9 of 23 pages
Issue: A 10/18/11
3. Unplug the vehicle 2 Pin connector as
shown.
4. Proceed with “Wire to Wire”.
Insert V5 2 Pin Connectors in
between vehicle 2 Pin connectors as
shown.
5. Secure the joint 2 Pin connectors onto
vehicle harness with 1 Wire Tie.
6. Secure the V5 4 Pin Connectors
(black) onto the vehicle harness with
1 Wire Tie.
Fig. B-4
V5 only
-If vehicle is equipped with V4
Harness already, skip to step 10
Fig. B-5
Fig.B-6
Side Cutter
SCION xD 2012 - TVIP V5
Procedure SCION SECURITY
Page 10 of 23 pages
Issue: A 10/18/11
7. Unplug the vehicle 8 Pin connector.
8. Proceed with “Wire to Wire”.
Insert V5 8 Pin Connectors in
between vehicle connectors.
9. Secure the joint 8 Pin connectors onto
the vehicle harness with 1 Wire Tie.
Move onto step 14.
10. If Vehicle is already equipped with V4
Harness, V5 Harness rides onto V4
Harness.
Clip off 1 Wire Tie holding V4 4 Pin
Connector.
11. Unplug 2 Pin Connectors (black) on
each of V4 and V5 Harnesses.
V5 onto V4
-Add On installation
Fig.B-7
Fig. B-8
Side Cutter
Fig. B-9
Side Cutter
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente