Screen Innovations Solo/Pro 2 Manuale utente
Solo / Pro 2
Installation Instructions
24V (Low Voltage) Motors
Screen Innovations
9715-B Burnet Rd, Suite 400 Austin, TX 78758
512.832.6939
www.screeninnovations.com
Rev B April 2019
CONTENTS
Initial Consideration ................................................... Pg 1
Parts in the Box - 24V RTS ........................................ Pg 2
Parts in the Box - 24V RS485 .....................................Pg 3
Spacer Blocks and Leveling Shims ......................... Pg 4
Pre-wire 24V RTS ......................................................... Pg 5
Pre-wire 24V RS485 .................................................... Pg 6
Power Wire distance chart ........................................ Pg 7
Installation .................................................................... Pg 8 - 16
24V RTS
Running ...................................................................... Pg 17
Programming ............................................................. Pg 18 - 19
Pairing another RF Remote ..................................... Pg 20
24V RS485
Programming with SIFI ..................................... Pg 21 - 24
Programming with Limit Setting Tool................... Pg 25 - 27
Control with 3rd Party - via Serial......................... Pg 28
Control with 3rd Party - via SIFI......................... Pg 30 - 31
Control with 3rd Party - via DCT......................... Pg 32 - 33
Thank you for purchasing an SI product. If you have
any questions or need any assistance with your
Solo Pro, we would love to help you.
Technical Support: 512.832.6939
Hours of Support: 7:30am - 5pm CST
screeninnovations.com
INITIAL CONSIDERATIONS
Thank you for your purchase of Solo/Pro 2. The
screen is mountable outdoors, but is not waterproof.
It has not been designed to be run or left in the rain or
condensing humidity. Also avoid water spray, splash
and extreme heat or cold. Protect your Solo/Pro 2. and
you can expect years of quality use.
For a quick install it is recommended you run
appropriate wire to the installation location before
installing the screen. See the Pre-Wire sections for your
particular control method for details.
Initial Considerations 1
CONTENTS (cont.)
Mounting Accessories ............................................Pg 34
Motor Accessories 24V RTS ...................................Pg 35
Motor Accessories 24V RS485................................Pg 36
Storage and Transport ........................................... Pg 37 - 38
Care and Maintenance ........................................... Pg 39
Troubleshooting ........................................................ Pg 40 - 43
Warranty ..................................................................... Pg 44
(4) Spacer blocks
(6) Wood
fasteners
Low Voltage
Power Supply
24V RS485
Additional accessories required
for RS485 control
Parts in the box
Solo/Pro 2 screen
RS485PWR
24v RS485 - Parts in the Box 3
(2) Ceiling/Wall
Locking brackets
Terminal block
receptacle and bracket
(6) Leveling
Shims
24V RTS
PWR Solo/Pro 2 screen
RF Remote
(4) Spacer
blocks
Low Voltage Power
Supply
Parts in the box
24v RTS - Parts in the Box 2
(2) Ceiling/Wall
Locking brackets
Terminal block
receptacle and bracket
(6) Wood
fasteners
(6) Leveling Shims
PRE-WIRE - 24V RTS
1. Run 2 conductor wires to the left side of screen
cassette installation location (refer to pg. 11). Follow
the power wire distance chart (refer to pg. 7) to
ensure use of the correct wire gauge.
2. Terminate the wires with the provided terminal block
as shown below.
+ 24 VDC
- 24 VDC
V+
V-
+
-
G
Not
used
Pre-Wire - 24v RTS 5
Spacer Blocks & Leveling Shims 4
SPACER BLOCKS & LEVELING
SHIMS
Spacer Blocks are used to
clear an obstruction on the
wall. Connect spacer block
to each wall bracket before
installation.
Leveling Shims are used if
the ceiling or other
mounting surface is out
of level or plumb. Connect
to ceiling brackets before
installation.
Do not use any combination above the line.
over 100
100
90
80
70
60
50
45
40
35
30
25
20
15
10
5
Distance
(ft.) 12 14 16 18 20 22 24
Standard Cu Wire Guage (min.)
POWER WIRE DISTANCE CHART
Power Wire Distance Chart 7
+ 24 VDC
- 24 VDC
Data +
Data -
Data ground
V+
V-
+
-
G
PRE-WIRE - 24V RS485
1. Run 5 conductor wires to the left side of screen
cassette installation location (refer to pg. 11). To be
sure you have the correct wire you can order SDN
wire directly from SI. If you are using third party wire,
follow the power wire distance chart (refer to pg. 7)
to ensure use of the correct wire gauge for the 24
VDC wires.
2. Terminate the wires with the provided terminal
blocks shown below.
Pre-Wire - 24v RS485 6
Solo/Pro 2 - Installation 9
13
4"
View Height
Drop
3.43”
(87mm)
2.02”
(51mm)
4.88”
(124mm)
3.43”
(87mm)
2.01”
(51mm)
3.78”
(96mm)
2.87”
(73mm)
2.85”
(72mm)
1.61”
(41mm)
Bracket
size
Small Medium Large
(cont. on next pg)
Proper mounting preparation will ensure a great
installation. Mounting brackets must be level to each
other, as well as plumb. They must be screwed into
structural members of some kind, such as ceiling joists
or wall studs. You may use the wood screws provided,
or other anchors (not provided) capable of carrying the
load, that is suitable to the substrate.
DO NOT MOUNT TO HOLLOW SHEET ROCK.
1. The drop is adjustable in the field between 0'' and the
MAX DROP (12'', 24'', or 36'', 4'' for short throw)
ordered for your screen. Use the drawing (refer to pg.
9) to pick a bracket height that will allow you to
extend your screen to achieve the desired vertical
position of your viewing area.
INSTALLATION
Solo/Pro 2 - Installation 8
wire
exits back
corner
of the
cassette
Cassette Length
View Width
Brackets secured to Wall or
Ceiling Structural Supports
Screen Centerline Structural Supports
2" Min to 8" Max
pull wire
through the
hole in gray
zone
Solo/Pro 2 - Installation 11
(cont. on next pg)
2. Determine the desired horizontal viewing position
centerline of the projected viewing area.
3. The Solo/Pro 2 screen must be installed with the
brackets no more than 8 inches from each end of
the cassette. Measure the overall length of the
cassette to determine the min and max horizontal
spacing of the mounts. Mark the location of the
brackets over a stud or ceiling joist and within an
appropriate distance from the ends. If the location
of the stud or ceiling joist does not allow the center
of the screen to match the projector lens' center,
another board or plate will have to be installed on the
wall or ceilng to take the mount fasteners.
Solo/Pro 2 - Installation 10
5. Ensure the wall bracket lever is down.
6. Connect the screen terminal block to the pre-wire
terminal block. Then press the connected terminal
block into the mount.
Solo/Pro 2 - Installation 13
Proper position
for installing
screen
(cont. on next pg)
4. Secure the brackets to the wall or ceiling structural
supports using appropriate fasteners. Make sure the
brackets are along the same level line. Install the
terminal block bracket next to the left bracket. This
bracket is used to hold the power and/or controls
terminal block easily out of sight.
Solo/Pro 2 - Installation 12
terminal block bracket
9. Use your preferred control method to deploy the
screen material and remove the weight bar shipping
locks.
Solo/Pro 2 - Installation 15
(cont. on next pg)
7. Hang the screen on the mounting brackets ensuring
that all hooks are engaged in the channel in the back
of the cassette.
8. Slide the cassette left to right to verify it is positioned
at your desired viewing location, then lock the screen
in place, rotating the wall bracket lever to the upward
position.
Solo/Pro 2 - Installation 14
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Screen Innovations Schermo di proiezione
Screen Innovations
Screen Innovations 5 Motorized Manuale utente
Screen Innovations
Screen Innovations Zero-G Manuale utente
Screen Innovations
Screen Innovations 5 Series Zero Edge Manuale utente
Screen Innovations
Screen Innovations 1 SERIES FIXED Manuale utente
Screen Innovations
Screen Innovations 7 Series Fixed Manuale utente
Screen Innovations
Screen Innovations 7 Series Fixed Manuale utente
Screen Innovations
Screen Innovations Transformer Manuale utente
Screen Innovations
Screen Innovations Solo 3 Indoor 575 External Manuale utente
Screen Innovations
Screen Innovations Solo 2 Manuale utente
Screen Innovations
Screen Innovations Solo Manuale utente
Screen Innovations
Screen Innovations Solo 3 Manuale utente
Screen Innovations
Screen Innovations 5 Series Curved Fixed Manuale utente
Screen Innovations
Screen Innovations ZERO EDGE PRO Manuale utente
Screen Innovations
Screen Innovations Solo Manuale utente
Screen Innovations
Screen Innovations 5 Series Fixed Manuale utente
