RC7-PD2™ Installation Instructions
Supporting the Poly EagleEye Director II
and Group Series 300, 500, 700 & 7500 Codecs
TEST YOUR SCTLink™ CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your
SCTLink™
wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1. Test and verify your CAT5e/CAT6 STP or UTP SCTLink™ cable for T568A or T568B.
The SCTLink™ cable must be between 10m (minimum) and 100m (maximum) length.
2. Connect one end of the SCTLink™ cable to the “SCTLink™” connection on the Head End module.
3. Connect the other end of your SCTLink™ cable to the provided PowerSniffer.
4. Connect the WPS-48 power supply to the Head End module.
5. Connect the WPS-48 power supply to AC mains.
6. If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result,
stop and re-terminate cable
.
7. Once your SCTLink™ cable has been tested, please disconnect the WPS-48 power supply from the RC7-HE module,
and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Before integrating your RC7-PD2™extension kit, please ensure your Poly EagleEye Director II base is connected to your two
EagleEyeIV cameras (Power and Ethernet connections) via Poly’s instructions.
Connect the camera-end cables:
1. Connect the RCC-C030 mini-HDCI end to the mini-HDCI
input on the EagleEye Director II base.
• Connect the RCC-C030 HDMI leg cable to the
RC7-CE’s HDMI “HDMI In” port.
• Connect the RJ45 leg cable to the RC7-CE’s
“Power Serial/IR” port.
2. Connect the RCC-C016 1’ Audio Cable between the RC7-
CE “Line Out” port and the EagleEye Director II’s audio
TRS input.
3. Connect the PPC-015 Power Cable between the
EagleEye Director II’s power input and the RC7-CE’s
power input, labeled “+12VDC Output”.
Connect the codec-end cables:
4. Connect the RCC-H030’s HDCI end to the primary HDCI
input on the Group Series codec.
• Connect the HDMI leg cable to the RC7-HE’s
HDMI “Output 1” port.
• Connect the 9Pin leg cable to the RC7-HE’s
port labeled ‘Serial/IR’.
5. Connect the Polycom supplied audio cable between the
RC7-HE’s “Line In” port and the Group Series Codec’s
audio outputs.
Connect and Initiate the Extended System:
6. Connect one end of your CAT6 SCTLink™ cable to the
RC7-HE module’s “SCTLink™” port. Connect the other
end to the RC7-CE module’s “SCTLink™” port.
7. Connect the WPS-48 Power Supply to the RC7-HE.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • ©SOUND CONTROL TECHNOLOGIES, INC
•ALLOW UP TO TWO MINUTES FOR THE EAGLEEYE DIRECTOR II SYSTEM TO INITIALIZE •
Power Supply Specications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC
power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE LED LABEL ACTIVE STATUS INACTIVE STATUS
RC7-CE OK LED Blinking Green (~1 second interval) Blinking or Solid Red
RC7-HE OK LED Blinking Green (~1 second interval) Blinking or Solid Red
RC7-HE LINK LED Solid Green Solid Red or Dormant
Cable Table - Part numbers, descriptions and functions of all provided SCT cables.
This kit includes [1] RC-RKM™ Rack Shelf.
CABLE DESCRIPTION FUNCTION
RCC-C030-0.4M HDMI/RJ45 to Mini-HDCI Cable Video/control connection between Director II base and RC7-CE Module.
RCC-C016-0.3M Audio Cable Audio connection between Director II base and RC7-CE module.
PPC-015-0.4M/PPC-002 Power Cable Supplies power from RC7-CE module to the Director II base.
RCC-H030-1.0M HDMI/ DB9 to HDCI Video/control connection between RPG Series Codec and RC7-HE module.
Updated: 9/30/2021
