Se-Kure Controls SP-101 Manuale utente
Installation Instructions for the
Fire Extinguisher Alarm SP-101
SP-101
Fire Extinguisher Alarm System w/Key, Sensor, Adhesive & Strap
SP-103
Special Beaded Strap
SP-102
Alarm Sensor
SP-909NP
Sensor Adhesive with
Neoprene
SP-1483
Extra Key
SP-1909
(2) 1" x 2" Adhesives
w/ Alcohol Prep Pads
Battery
Connector
Sensor Port
9-volt Alkaline
Battery
(Not Supplied)
Cover
Plate
(4) Phillips Head (Cover Plate) Screws
Battery Installation:
1. Remove the (4) phillips head
screws to open the battery
compartment as shown in the
diagram below.
2. Insert the key, push in and
turn clockwise.
(This places the Alarm in the
“Stand-by” position).
Note: The key can only be
removed in the “ON” position.
3. Attach a 9-volt alkaline battery
(Not Supplied) to the
connector, and insert the
battery into the compartment.
4. Replace the cover plate and
the (4) phillips head screws.
(Note: Tighten screw until it
stops–Do Not Over-Tighten).
Se-Kure Controls,
®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-(800) 322-2435 • (847) 288-1111 • Fax: (847) 288-9999
Rev. 11/21/97 SCI-9596©1997 Se-Kure Controls,
®Inc.
Assembly Instructions:
1. Remove the old beaded strap holding the fire
extinguisherʼs pin in place.
(DO NOT REMOVE PIN OR INSPECTORʼS TAG).
2. Hold the sensor in place on the extinguisherʼs handle, and
thread the new (red) beaded strap through the sensor
hole, as shown in Fig. 1 at left.
3. Lasso the handle with the beaded strap by passing it
around the entire handle, up through the ring of the pin,
and into the straps locking hole. (Shown in Fig. 2 at left).
(Note: the fire extinguisher strap is imprinted with the word
ENTER to indicate which way to insert the end).
4. Pull the strap up tight making sure the sensor lays “flat”
on the handle, as shown in Fig. 3. Fig. 4 shows the
completed assembly.
5. Place the double sided
adhesive on the Alarm
Module back, and mount
the module to the wall near
the fire extinguisher, as
shown in Fig. 5.
6. Plug the sensor into the
Alarm unit and turn the key
to the “ON” position, and
remove, (shown in Fig. 6).
Your Fire Extinguisher Alarm is now “ON” and ready
to )))sound((( an alert when used or tampered.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Battery Test Button
(2) 1" x 2"
Base Adhesives
W
A
L
L
VERY IMPORTANT!
NOTE: Clean the
back of the Alarm
Module with an
Alcohol Prep Pad,
and wipe the
surface DRY with a clean
paper towel.
Clean &
Wipe Dry
Altri manuali Se-Kure Controls Sistema di sicurezza
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Se-Kure Controls
Se-Kure Controls LE PLUS Manuale utente
Se-Kure Controls
Se-Kure Controls SK-554 Manuale utente
Se-Kure Controls
Se-Kure Controls SK-800KME Series Manuale utente
Se-Kure Controls
Se-Kure Controls Vantage II Manuale utente
Se-Kure Controls
Se-Kure Controls SK-903KB Manuale utente
Se-Kure Controls
Se-Kure Controls Klothing Kontrols SK-3600 Series Manuale utente
Se-Kure Controls
Se-Kure Controls SK-554NP-RKAC-4 Manuale utente
Se-Kure Controls
Se-Kure Controls ME Jr. plus 2 SK-800MEI Series Manuale utente
Se-Kure Controls
Se-Kure Controls K-9 WatchDog Manuale utente
