Seada G44 Series Manuale utente

G44 User Guide

This user guide provides basic instructions for setting up SEADA G44 video wall controllers using its

management software.

Document No. SD-MA-027

Document Version: 02

 G44 User Guide
 
 
Table of Contents 
Product Introduction.......................................................................................................................3 
1. Product profile ........................................................................................................................3 
2. Product capability ...................................................................................................................3 
3. Specification & Parameters.....................................................................................................3 
Hardware Overview ........................................................................................................................5 
G44 Software ..................................................................................................................................6 
1. Matrix Switch ..........................................................................................................................6 
 Audio route.............................................................................................................................9 
2. Advanced Switch.....................................................................................................................9 
3. Signal settings .......................................................................................................................12 
4. FineTune: PQ & Position .......................................................................................................12 
5. OSD Control...........................................................................................................................13 
6. TV Wall..................................................................................................................................16 
7. Web Control..........................................................................................................................17 
Front Panel....................................................................................................................................20 
1. LCM display...........................................................................................................................20 
2. Audio Input Select (Default: Inner).......................................................................................20 
3. Output Audio Select (Default: Inner)....................................................................................21 
4. Audio Switch .........................................................................................................................21 
5. Video Switch..........................................................................................................................22 
6. Video + Switch.......................................................................................................................22 
7. Input Type Setting.................................................................................................................23 
8. Output Type Setting..............................................................................................................23 
9. Output Resolution Setting ....................................................................................................24 
10. Recall.....................................................................................................................................24 
11. Save As ..................................................................................................................................25 
Command Lines.............................................................................................................................26 
Troubleshooting............................................................................................................................29 
1. No Connection ......................................................................................................................29 
2. No Output .............................................................................................................................29 
3. Black screen ..........................................................................................................................29 
 
 
 

G44 User Guide

1. Product Introduction

1.1. Product profile

⚫G44 video wall controller can support up to 4 inputs/4 outputs.

⚫It supports HDMI, DVI, VGA, YPbPr, CVBS signal input/output through DVI-U jacket.

⚫It support RS232 communication interface, through the special PC tool to control the matrix

signal switching, monitoring the working state of the matrix, set the signal resolution, etc..

⚫Seamless switching available;

1.2. Product capability

⚫Support 4 inputs and 4 outputs，4 L/R audio inputs and 4 L/R audio outputs;

⚫Support HDMI/DVI, VGA, YPbPr, CVBS input;

⚫Support HDMI/DVI, VGA, YPbPr, CVBS output;

⚫Support a maximum resolution of 1600 x 1200@60hz;

⚫Support RS232 port control

⚫Support network port control

⚫Support IR remote control

⚫Support front panel button control

⚫Scalar inside, output resolution control available;

1.3. Specification & Parameters

Input

Interface

Signal

DVI-U

HDMI

HDMI -1.3

DVI

DVI 1.0

VGA

800x600,1024x768,1280x768,1280x800,1280x1024,136

0x768,1400x1050,1600x1200,1920x1080

YPbPr

576i50,720p50,720p60,1080i50,1080i60,

1080p50,1080p60

CVBS

PAL，NTSC

Output

Interface

Signal

DVI-U

HDMI

HDMI V1.3A

1024x768,1280x1024,1360x768,1280x720

1600x1200,1920x1080,1680x1050

DVI

DVI 1.0

1024x768,1280x1024,1360x768,1280x720

1600x1200,1920x1080,1680x1050

VGA

1024x768,1280x1024,1360x768,1280x720

1600x1200,1920x1080,1680x1050

YPbPr

1080p60，720p60

CVBS

PAL/NTSC

Control

RS232

D-sub 9

Baud rate：9600

Size

W*D*H

430（mm）×220（mm）×44（mm）

G44 User Guide

Power

12V/3A power adapter

Power

consumption

25W

Temperature

Operating

temperature

0℃—40℃

G44 User Guide

2. Hardware Overview

Model: G44-DVI

1 –Display

2 –Input Buttons

3 –Output Buttons

4 –Function Buttons

Back Panel includes 4 DVI-U Inputs and

Outputs, Ethernet control port, 2x Serial ports

and 4 3.5 mm captive screw connectors for

audio inputs and outputs

LCM

G44 User Guide

3. G44 Software

Users can run the G44.exe software directly without

installation. It requires password authentication:

Default password for Administrator is: 111111

Default password for User is: 000000

There are 7 main tabs in this software: Matrix Switch, Advanced Switch, Signal Setting, Fine Tune, OSD

CTRL, TV Wall, Network Setting.

3.1. Matrix Switch

Users can configure the G44 device and connect the device to control PC in this section.

3.1.1. Connect to the G44 via UART

Connect the G44 to the control PC with a serial cable

1. Click the dropdown menu right of Port to select the COM port.

2. Click the button right of Status to connect to the device (the button will change from

Disconnected to Connected)

3. If the COM port does not exist, then the PC tool will show a

message of ‘COM x not detected!’. If this message occurs, you

should start from step 1 after you connect a serial cable to the

computer.

G44 User Guide

4. If the device or the connection is faulty, then a message will

occur as follows after 3 seconds. Please check if your device or

hardware connection is correct.

5. If all is right, the PC tool will read some information

from the device. It probably takes 5 seconds and it will

show ’Reading: All information success!” when

finished.

3.1.2. Connect to the G44 via Network

The default IP address for G44 controller is 192.168.0.247 Users need to change the IP address of

the control PC to the same network segment as the G44.

•Change the ‘Obtain an IP address automatically’

to ‘Use the following IP address’ to set up a static IP address of TCP/IPv4 in Ethernet Properties

➢IP address: any address between 192.168.0.2 and 192.168.0.254 except the address which has

been taken by the G44

➢Subnet mask: 255.255.255.0, Default Gateway: 192.168.0.1

•Once the control PC IP address having been set up, connect PC to either the RJ45 ports of

G44 controllers via a network cable and then press the Connect button to connect the device.

3.1.3. Matrix Switch Routing

Users can switch and assign different inputs to the

selected outputs in the matrix. The name of the

input/output can also be changed by selecting the

default name –Input1/Video-Output1 and

replacing it with the chosen name.

3.1.4. Allset, Recall, Save As and Reset

The G44 unit has 32 modes (or

presets) already saved. Selecting

one of them from the recall Menu will select that specific preset.

If you would like to save a preset you have already created, select the dropdown menu and choose

which slot you want to save it in.

Finally, the Allset dropdown menu helps the users select a single input to be displayed on all of the

screens (i.e. Allset Input 4 would display Input 4 on Output 1, Output 2, Output 3 and Output4.)

G44 User Guide

The reset button, resets the default settings of the unit –Input 1 mapped to Output 1, Input 2

mapped to Output 2 etc. (Including the audio)

3.1.5. Presentation Mode

From the dropdown menu in the top-right corner, users can select either Matrix mode or

Presentation mode.

•Matrix Mode –The Inputs and their audio source are mapped to each other. Meaning that

Input 1 will have the audio source from Input 1, Input 2 will have the audio source from

Input 2 etc.

•Presentation Mode –This allows the user to control the audio source separately –The video

screen can display input 2, however the audio source can be any of the inputs (including

input 2)

Video and audio can be controlled separately(default):

Video and audio can be controlled together. And then you can select which audio channel will be

controlled.

G44 User Guide

Audio route

Click to control audio route. And the blue button represents current route information.

NOTE: Audio output X has two type (L/R and Inner).

3.2. Advanced Switch

The PC tool support automatically switch the input source periodically for the output port in order to

facilitate the demonstration functions needed in some scenarios.

Operation guide is as follows:

1. Click the output port that needs configuring （Also we can press ‘Ctrl’ or ‘Shift’ first, then click to

select more output ports）

G44 User Guide

2. Press ‘Ctrl’ or ‘Shift’ first, then click to select input ports

3. Click “-->” button to add the input ports selected in step 2 .

4. Check the output ports that need to automatically switch input source periodically.

5. Configure automatically switch Switch frequency: default 2000ms

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Seada Monitor

Seada

Seada SD-MV-CM61 Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione