Seagate Hawk 2 ST12400N Manuale utente

. . . . . . . . . . . . . . . . . . . . . . . . . . .

ST12400N/ND/NC

ST11900N/ND/NC

HAWK 2 Family:

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation Guide

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

Introduction ........................................................ 1

Electromagneticinterference ............................ 1

Before you begin ................................................ 2

Installation overview .......................................... 7

Product repair information ................................ 9

Shipping ......................................................... 10

Product repair and return information............. 10

Technical support services ............................... 11

Drive specifications............................................ 14

Initial set-up information.................................... 17

Drive configuration............................................. 23

Drive installation................................................. 33

Drive Setup ......................................................... 37

Publication Number: 77767451, Rev. C.

March 1994

Seagate®,SeagateTechnology®andtheSeagatelogo

areregisteredtrademarksofSeagateTechnology,Inc.

HawkTM, SeaFAXTM, SeaFONETM, SeaTDDTM,

SeaBOARDTM aretrademarksofSeagateTechnology,

Inc.Otherproductnamesareregisteredtrademarksor

trademarks of their own.

Seagate reserves the right to change, without notice,

product offerings or specifications. No part of this

publication may be reproduced in any form without

written permission of Seagate Technology, Inc.

Hawk 2 Family Installation Guide, Rev. C 1

Introduction

Beforeattemptinganyinstallation,pleasereadthrough

all applicable sections of this document, including all

warnings and cautions.

Warning. This equipment generates, uses, and can

radiate radio frequency energy and if not

installedin accordancewith theseinstruc-

tions,maycauseinterferencetoradiocom-

munications.

Electromagnetic interference (EMI) con-

siderations

The drive(s) described herein, as delivered, are de-

signed for system integration and installation into a

suitable enclosure prior to use. As such, the drive(s)

described herein are supplied as a sub-assembly and

arenotsubjecttoSubpartJofPart15oftheFCCRules

and Regulations nor the Radio Interference Regula-

tionsoftheCanadianDepartmentofCommunications.

However,theunithasbeentestedusingpropershield-

ing and grounding and found to be compliant with the

ClassAlimits oftheFCCRulesand the Regulationsof

the Canadian Department of Communications.

2Hawk 2 Family Installation Guide, Rev. C

The physical design characteristics of the drive(s)

described herein, serve to minimize EMI radiation

when installed in an enclosure that provides reason-

able shielding. As such, the drive(s) are capable of

meeting the Class B limits of the FCC Rules and the

RegulationsoftheCanadianDepartmentofCommuni-

cations.

Note. It is the end users' responsibility to assure that

the drive(s)describedhereinmeettheappropri-

ate EMI requirements of their system. Shielded

I/Ocablesmayberequirediftheenclosuredoes

notprovideadequateshielding.IfI/Ocablesare

externaltotheenclosure,shieldedcablesshould

beused,with theshieldsgroundedto theenclo-

sure and to the host controller.

Before you begin

Verify that the system is switched off and discon-

nected from main power before any installation is

attempted.

Protect yourself, the drive, and your valuable pro-

grams and data by reading the following cautions

and warnings.

Hawk 2 Family Installation Guide, Rev. C 3

•Donotunpackdrive fromitsstaticshieldedbaguntil

you are ready to install it in the system.

•Always handle the drive by the frame or casting.

•Do not touch printed circuit board (PCB) or the I/O

connector pins.

•Never apply pressure to the PCB or to the drive top

cover.

•Donottamperwith sealedtopcover.Doingsovoids

your warranty. The drive contains no user service-

able components. See Product Repair section for

moreinformation.

•Visually inspect the shipping container for any obvi-

ous damage.

•Inspectdriveforpossibleshippingdamage.Allclaims

of this type should be filed promptly with the trans-

porterinvolved.Saveoriginalpackingmaterialstobe

used when reshipping.

•When transporting or shipping a drive or system,

please ensure that they are correctly packed in

originalSeagate approved(or equivalent)container

and shipped via an air-ride carrier experienced in

handling computer equipment.

•Verifyallpartslistedonshippingbillarereceivedwith

theequipment. Discrepanciesordamage shouldbe

reported to the shipping company.

4Hawk 2 Family Installation Guide, Rev. C

Caution. Thecircuitassembliesandcomponentscon-

tained in this equipment can be degraded or

destroyedbyElectrostaticOverstress(EOS)

or by Electrostatic Discharge (ESD).

Static electrical charges can accumulate

quickly on personnel, clothing and synthetic

materials.Theelectrostaticfieldsduetothese

charges when brought in close proximity to

susceptible circuit assemblies and compo-

nents, can result in degraded reliability or

immediatefailureof the affectedcomponent

or assembly.

Toinsureoptimumreliableequipmentopera-

tion, it is required that technical support per-

sonnel discharge themselves by wearing a

grounding strap around the wrist and be

connectedtoagroundingterminalwhilework-

inginthevicinityof,andwhilehandlingEOS/

ESDsusceptibleassemblies/parts.Ifunavail-

able,ground yourselffrequently bytouching

the metal chassis of the system before han-

dling any components (this helps only if the

system is connected to a ground).

Avoid

static-inducing carpeted areas.

This proce-

dure is especially important when handling

printed circuit boards (PCBs).

Hawk 2 Family Installation Guide, Rev. C 5

Safety instructions

1. The disc drive(s) are to be installed in a customer

suppliedenclosurewherethesurroundingairdoes

not exceed 50oC.

2. Four (4) 6-32 UNC-2A screws are required for

installation. Maximum screw length into side of

drive is 0.15 inches (3.81 mm). Maximum screw

lengthintobottomis0.20in.(5.08 mm).Maximum

screw tightening torque is 8.0 in-lb (0.90 NM) with

minimumthreadengagementof0.12in.(3.0mm).

3. Thepower requirementsare showninSection 1.0

ProductInformation.

4. The power supply must satisfy the safety require-

ments for SELV (Safety Extra Low Voltage) cir-

cuits.

5. Service is to be provided by trained Seagate ser-

vice personnel.

6. The incorporation of the disc drives listed in this

guide into a customer enclosure must meet the

appropriate safety requirements of the country in

which it is used (e.g. UL 1950, CAN/CSA-C22.2

No.950-M89,DINVDE0805/05.90andEN60950:

1988 (IEC 950).

6Hawk 2 Family Installation Guide, Rev. C

Sicherheitsanleitung

1. DäsGerätisteinEinbaugerät,vorgesehenfüreine

maximale Umgebungstemperatur von 50oC.

2. Zur Befestigung der Drive werden 4 Schrauben

benötigt (6-32 UNC-2A). Die maximale Länge der

Schrauben in der unteren Seite des Chassis darf

nicht mehr als 0.20 in (5.08 mm) betragen, die in

der oberen 0.15 in (3.81 mm). Maximalle

Schraubenaziehung Von 8.0 in-lb (0.90 NM) mit

minimalem Gewindeansperuch 0.12 in. (3.0 mm).

3. Die Versorgungsspannungen werden im Kapitel

1.0 (Produkt Information) gezeigt.

4. Die Versorgungsspannung muss SELV entspre-

chen.

5. AlleArbeitendürfennurvonausgebildetemSeagate

Service-Personal durchgefürhrt werden.

6. Der Einbau des Drives muss den Anforderungen

gemässDINVDE0805/05.90oderEN60950:1988

(IEC 950).

Hawk 2 Family Installation Guide, Rev. C 7

Installation Overview

Installation of the drive can be divided into distinct

phases as outlined below. Some of these may not be

applicable to your particular installation requirements.

Refer to the individual drive installation sections for

specific information on your drive model.

•Driveconfiguration:Theusermustselectwhichof

thedrivefeaturesareappropriatetoenableforinstal-

lationintheirsystem.Thisisdonebywayoftheuser

configuration jumpers found on the drive PCB.

•Mechanical installation: After setting up the drive

configuration the drive must be mechanically in-

stalled into the host system and the power and

I/O cables attached. Previously mentioned precau-

tions should be observed

•SCSI drives should not be defined in the CMOS:

The SCSI Host adapter has its own BIOS to handle

the Input/output procedures. The CMOS setting for

SCSI drive is either drive type zero, or the "no drive

installed"option.

8Hawk 2 Family Installation Guide, Rev. C

•Low-level formatting: After the drive has been

properly configured for the system, it does not need

to be low-level formatted, as this has been done by

the factory and does not require this step during

installation. (The low-level format writes the sector

boundariesandtrackinformationtothedrive).Defect

managementinformationisreadfromthedrivebythe

host system when required in the installation proce-

dure. If an installed drive is low-level formatted, all

user data stored on the drive will be lost.

Note. SeagateTechnologyassumes noliability for

lost user data.

•Partitioning and high level formatting: A drive

canbesub-dividedinto"partitions"whichbehaveas

individualdriveswithinthesystem.Seeyoursystem

documentation. Present day drive installation pro-

grams have menus that lead you through these

installationprocedures.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Seagate Magazzinaggio

Seagate

Seagate ST8000VE000 Manuale utente

Seagate

Seagate ST6000NM0115 Manuale utente

Seagate

Seagate Cheetah NS 10K Manuale utente

Seagate

Seagate ST9120315AS - Momentus 5400.6 120 GB Hard... Manuale utente

Seagate

Seagate Pipeline HD Pro Serial ATA ST31000533CS Manuale utente

Seagate

Seagate ST39204LC - Cheetah 9.2 GB Hard Drive Manuale utente

Seagate

Seagate Nytro XF1230-1A0240 Manuale utente

Seagate

Seagate Barracuda 5400.1 ST340015A Manuale utente

Seagate

Seagate STU62001LW-S Manuale utente

Seagate

Seagate Backup Plus Desktop Manuale utente

Seagate

Seagate Barracuda 7200.14 Manuale utente

Seagate

Seagate GoFlex Satellite Manuale utente

Seagate

Seagate ST9100A Manuale utente

Seagate

Seagate ST6000NM000B Manuale utente

Seagate

Seagate GoFlex STBL500100 Manuale utente

Seagate

Seagate BARRACUDA 50 Manuale utente

Seagate

Seagate IronWolf Pro ST8000NE001 Manuale utente

Seagate

Seagate ST9100822A Manuale utente

Seagate

Seagate ST9100824A - Momentus 5400.2 100 GB Hard... Manuale utente

Seagate

Seagate SkyHawk ST6000VX001 Manuale utente

Seagate

Seagate Barracuda ST3000DM001 Manuale utente

Seagate

Seagate EXOS ST16000NM007G Manuale utente

Seagate

Seagate ST9160411AS - Momentus 7200.3 160 GB Hard... Manuale utente

Seagate

Seagate Lyve Drive Shuttle Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente