Seagull Models Piper Cub Manuale utente

ASSEMBLY MANUAL

MadeinVietnam.

“Graphics and specfications may change without notice”.

Kit features.

• Ready-made—minimalassembly&finishingrequired.

• Ready-coveredcovering.

• Photo-illustratedstep-by-stepAssemblyManual.

Specifications

Wingspan-----------------------------------------78.7in---------------------------200cm.

Wing area----------------------------------------- 906.8 sq.in--------------- 58.5 sq.dm.

Approximate flying weight---------------------7.5- 9.3 lbs----------------3.4 - 4.2kg.

Length----------------------------------------------51.1in-------------------------129.8cm.

Recommended engine size---------------- .61 - .75 cu.in---------------- 2-stroke.

.82 - .91cu.in-----------------4-troske.

Radio System required 4 channels with 6 servos

Flying skill level Intermediate/advanced.

MS: 87

PIPER CUB _ CODE SEA 87.Instruction Manual

INTRODUCTION.

Thankyou for choosing the PIPER CUB ARTFby SEAGULLMODELS. The PIPER CUB was

designed with the intermediate/advanced sport scale in mind. It is a semi scale airplane which is

easytoflyandquicktoassemble.Theairframeisconventionallybuiltusingbalsa,plywoodtomake

itstrongerthantheaverageARTF,yetthedesignallowstheaeroplanetobekeptlight.Youwillfind

thatmostoftheworkhasbeendoneforyoualready. Themotormounthasbeenfittedandthehinges

are pre-installed . Flying the PIPER CUB is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your PIPER CUB. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it

is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C

supplierandjoinyourlocalR/CModelFlyingClub.R/CModelFlyingClubsofferavarietyoftraining

proceduresdesignedtohelpthenewpilotonhiswayto successful R/C flight. They will also be able

to advise on any insurance and safety regulations that may apply.

ADDITIONAL ITEMS REQUIRED.

.61 - .75 cu.in 2-stroke engine

.82 - .91 cu.in 4-stroke

6 servos

Glow plug to suit engine

Propeller to suit engine

Protective foam rubber for radio

system

Silicone fuel line

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue

30 minute epoxy

5 minute epoxy

Hand or electric drill

Assorted drill bits

Modellingknife

Straight edge ruler

2mm ball driver

Phillips head screwdriver

220 grit sandpaper

90° square or builder’s triangle

Wire cutters

Masking tape & T-pins

Thread-lock

Paper towels

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage

WING ASSEMBLY

(1) Right wing

(1) Left wing

(2) Aluminium dihedral brace

Tail section assembly

(1) Horizontal stabilizer/ elevator

halves.

(1) Rudder halves.

Some more parts.

HARDWAREPACK

COWLING

Landinggear.....

www.seagullmodels.com

1) Carefully remove the aileron from one

of the wing panels. Note the position of the

hinges.

2)Remove each hinge from thewing panel

and aileron and place a T-pin in the center of

each hinge. Slide each hinge into the wing

panel until the T-pin is snug against the wing

panel. This will help ensure an equal amount

ofhingeison either side ofthehingelinewhen

the aileron is mounted to the aileron.

3) Slide the wing panel on the aileron until

there is only a slight gap. The hinge is now

centered on the wing panel and aileron.

Remove the T-pins and snug the aileron

against the wing panel.A gap of 1/64” or less

shouldbe maintained betweenthe wing panel

andaileron.

The control surfaces, including the

ailerons, elevators, and rudder, are

prehinged with hinges installed, but the

hinges are not glued in place. It is

imperativethat you properly adhere the

hingesin place per the steps that follow

using a high-quality thin C/A glue.

Note:

4)Deflect the aileron and completely

saturate each hinge with thin C/A glue. The

aileronsfrontsurfaceshould lightly contact the

wing during this procedure. Ideally, when the

hinges are glued in place, a 1/64” gap or less

will be maintained throughout the lengh of the

aileron to the wing panel hinge line.

Note: The hinge is constructed of a special

material that allows the C/A to wick or

penetrateanddistributethroughout the

hinge, securely bonding it to the wood

structureof the wingpanel and aileron.

To avoid scratching your new aero-

plane we suggest that you cover your work-

benchwith an oldtowel. Keepa couple ofjars

orbowlshandytoholdthesmallpartsafteryou

open the bags.

Pleasetrialfitallparts.Makesureyouhavethe

correct parts and that they fit and are aligned

properlybeforegluing!Thiswillensureproper

assembly as the PIPER CUB is made from

natural materials and minor adjustments may

havetobemade. Thepaintandplasticparts

usedinthiskitarefuelproof.However,theyare

not tolerant of many harsh chemicals includ-

ingthefollowing:paintthinner,cyano-acrylate

glueaccelerator,cyanoacrylategluede-bonder

andacetone.Donotletthesechemicalscome

incontactwiththecoloursonthecoveringand

the plastic parts.

NOTE:

HINGING THE AILERONS.

Hinge.

T- pin.

Hinge.

T- pin.

C/Aglue.

5) Turn the wing panel over and deflect the

aileron in the opposite direction from the

opposite side. Apply thin C/A glue to each

hinge,makingsure that the C/Apenetratesinto

both the aileron and wing panel.

6)Using C/Aremover/debonderandapaper

towel, remove any excess C/A glue that may

haveaccumulatedonthe wing or intheaileron

hingearea.

7) Repeat this process with the other wing

panel, securely hinging the aileron in place.

PIPER CUB _ CODE SEA 87.Instruction Manual

8)After both ailerons are securely hinged,

firmly grasp the wing panel and aileron to

make sure the hinges are securely glued and

cannot be pulled out. Do this by carefully

applying medium pressure, trying to separate

the aileron from the wing panel. Use caution

not to crush the wing structure.

TURNBUCKLE INSTALLATION.

Installing the turnbuckle for the wing as

same as pictures below.

Work the aileron up and down several

times to “work in” the hinges and check

for proper movement.

Note:

Hinge.

Theholelocationofturnbuckles shown in pic-

ture below .

Washer.

washer. Turnbuckle.

Turnbuckle.

3x20mm.

TURNBUCKLE INSTALLATION.

Theholelocationofturnbuckles shown in pic-

ture below .

HINGING THE RUDDER.

Glue the rudder hinges in place using the

same tectniques used to hinge the ailerons.

wing

Bottom.

wing

Bottom.

HINGING THE ELEVATOR.

Glue the Elevator hinges in place using the

same tectniques used to hinge the ailerons.

www.seagullmodels.com

Aileron control horn: See pictures below.

AILERON CONTROLHORN

ELEVATOR CONTROL HORN.

M3LOCK

NUT.

ALUMINUMWASHER.

CONTRONLHORN

M3 SCREW.

20mm.

Epoxy.

Wing

Epoxy.

Wing

Install the elevator control horn using the

same method as with the aileron control

horns.

2 sets.

3x35mm.

2 sets.

3x40mm. AluminumWasher.

16mm.

M3LOCKNUT.

Epoxy.

AluminumWasher.

Wing. Aileron.

Horizontal

Stabilizer.

Horizontal

Stabilizer.

CONTRONLHORN

M3 SCREW.

Installing theturnbuckle for tail strut of hori-

zontal fin as same as pictures below.

Horizontal fin bottom.

Turnbuckle.

Tail fin bottom.

PIPER CUB _ CODE SEA 87.Instruction Manual

16mm.

See pictures below.Make yourself the

template of your engine on paper.

ENGINE MOUNT INSTALLATION.

Mark and drill 4 holes for engine mount.

Insert 4 blind nuts to firewall.

4x30mm.

Thread locker glue.

Rudder control horn:

Usingthesametectniquesused aileron control

horn. See picture below.

2 sets.

3x35mm.

EPOXY.

Ruddercontrolhorn.

Rudder.

FUSELAGE.

RUDDER CONTROL HORN.

Elevator control horn.

CONTRONL HORN

M3 SCREW.

M3 LOCK NUT.

ALUMINUMWASHER.

EPOXY.

FUSELAGE.

ALUMINUMWASHER.

Rudder.

www.seagullmodels.com

Vent tube. Fuel pick up tube.

Fuel fill tube.

2) Usinga modeling knife, cut onelength

ofsiliconfuel line. Connect oneend of theline

tothe weighted fuel pick up andthe other end

to the nylon pick up tube.(The silicon tube is

not included).

3) Carefully bend the second nylon tube

up at a 45º angle. This tube is the vent tube.

1) Using a modeling knife, carefully cut

off the rear portion of one of the 3 nylon tubes

leaving 1/2” protruding from the rear of the

stopper. This will be the fuel pick up tube.

INSTALLING THE STOPPER ASSEMBLY.

FUEL TANK INSTALLATION.

You should mark which tube is the vent

and which is the fuel pickup when you

attach fuel tubing to the tubes in the stopper.

Once the tank is installed inside the fuselage,

it may be difficult to determine which is which.

Plastic tape.

4) Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using a

modeling knife. If flashing is present, make

sure none falls into the tank.

5) With the stopper assembly in place,

the weighted pick-up should rest away from

therear of the tank and move freely inside the

tank. The top of the vent tube should rest just

below the top of the tank. It should not touch

the top of the tank.

Important: When the stopper assembly is in-

stalled in the tank, the top of the vent tube

should rest just below the top surface of the

tank. It should not touch the top of the tank.

Carefully use a lighter or heat gun to

permenently set the angle of the vent tube.

6) When satisfied with the alignment of

the stopper assembly tighten the 3 x 20mm

machine screw until the rubber stopper ex-

pands and seals the tank opening. Do not

overtighten the assembly as this could cause

the tank to split.

PIPER CUB _ CODE SEA 87.Instruction Manual

1) Assemble and mounting the wheel as

shown in the following pictures.

2) Follow diagram below for wheel

installation:

Blow through one of the lines to ensure

thefuel lines have not become kinked in-

side the fuel tank compartment. Air should

flowthrough easily.

WHEEL INSTALLATION.

Landinggear.

Wheel.

Wheel collar.

Fuel pick-up tube.

Fuelfill tube.

Venttube.

Fueltank.

Balsa Block.

C/Aglue.

M2 x 6mm.

www.seagullmodels.com

3) A drop of C/A glue on the wheel collar

screws will help keep them from coming lose

duringoperation.

Repeat the process for the other wheel.

INSTALLING THE LANDING GEAR

1.5mm diameter.

1.5mm diametter.

M3x10mm.

Wheel

Fairing.

4) Remove the engine. Using an drill bit,

drill the mounting holes through the engine

mount at the four locations marked.

 2) Place your engine onto the engine

mount. Adjust the engine is centered of the

edges of the engine case.

 3) When you are satisfied with the align-

ment, mark the locations of the engine

mounting.



1) Install the pushrod housing through the

predrilledholein the firewallandintothe servo

compartment. The pushrod housing should

protrude 1/4" out past the front of the firewall.

Makea Z-Bend 1/4"fromone end oftheplain

wire pushrod.

MOUNTING THE ENGINE.

M2 x 8mm.

PIPER CUB _ CODE SEA 87.Instruction Manual

COWLING INSTALLATION.

1) Slide the fiberglass cowl over the en-

gineandline up thebackedge of the cowlwith

themarks you made on thefuselage thentrim

and cut.

Becauseof the sizeof the cowl,itmay benec-

essaryto use a needle valveextension forthe

highspeedneedle valve. Make thisoutof suf-

ficient length 1.5mm wire and install it into the

end of the needle valve. Secure the wire in

placeby tightening theset screwin the sideof

the needle valve.

 6) AttachtheZ-Bendin the pushrodwire to

the throttle arm on the carburetor.

 5) Bolttheenginetotheenginemountusing

the four machine screws. Double check that

all the screws are tight before proceeding.

MachineScrew 4x30mm.

Trim and cut.

MachineScrew 4x30mm.

Pushrodwire.

4.2 mm diameter.

140mm.

Indice

Altri manuali Seagull Models Giocattolo

Seagull Models

Seagull Models Ultimate Manuale utente

Seagull Models

Seagull Models RACER DELTA 40-46 Manuale utente

Seagull Models

Seagull Models Radial Rocket JD 10cc Manuale utente

Seagull Models

Seagull Models SPACE WALKER II Manuale utente

Seagull Models

Seagull Models steen skybolt n250sb Manuale utente

Seagull Models

Seagull Models HARMON ROCKET III Manuale utente

Seagull Models

Seagull Models MAXI LIFT 33cc Manuale utente

Seagull Models

Seagull Models SPORT CRUISER Manuale utente

Seagull Models

Seagull Models YAK 54 Manuale utente

Seagull Models

Seagull Models SEA 334 Manuale utente

Seagull Models

Seagull Models Ultimate Manuale utente

Seagull Models

Seagull Models Boomerang 40 Manuale utente

Seagull Models

Seagull Models WESTLAND LYSANDER MK. III 55CC SEA216 Manuale utente

Seagull Models

Seagull Models Magic Bird EF1 RACER 40E PNP, 46" Manuale utente

Seagull Models

Seagull Models DEWOITINE D.520 Manuale utente

Seagull Models

Seagull Models BUNKER BU 133 Manuale utente

Seagull Models

Seagull Models ANGEL GLIDER 2000 Manuale utente

Seagull Models

Seagull Models Grumman F8F Bearcat Manuale utente

Seagull Models

Seagull Models LANCAIR LEGACY Manuale utente

Seagull Models

Seagull Models Mehari Aerobatics CEA-309 Manuale utente

Seagull Models

Seagull Models MINI CHRISTEN EAGLE II N54CE Manuale utente

Seagull Models

Seagull Models ultra-jet Manuale utente

Seagull Models

Seagull Models Skyraider WARBIRD 10CC Manuale utente

Seagull Models

Seagull Models SEA FURY Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente