Seagull Models SEA 358 Manuale utente

ASSEMBLY MANUAL

Specications:

Wingspan------ 103 in (262 cm).

Wing area------ 1839.9 sq.ins (118.7sq.dm).

Weight---------- 25.3-26.9 lbs (11.5-12.2 kg).

Length---------- 66.7 in (169.3 cm).

Engine---------- 50cc-62 cc

Radio----------- 5 channels with 6 servos

Motor 360/ 3000watt/ ESC 160A-200A/ Lipo 12s;

Electric propeller 24x10 - 26x8

ITEM CODE : SEA 358

Code : SEA 358

1/3 ScaleMorane Saulnier AI Instruction Manual.

ank you for choosing the 1/3 Scale Morane Saulnier AI ARTF by SG MODELS . e

1/3 Scale Morane Saulnier AI was designed with the intermediate/advanced sport yer in

mind. It is a semi scale airplane which is easy to y and quick to assemble. e air-

frame is conventionally built using balsa, plywood to make it stronger than the aver-

age ARTF, yet the design allows the aeroplane to be kept light. You will nd that most

of the work has been done for you already. e motor mount has been tted and

the hinges are pre-installed. Flying the 1/3 Scale Morane Saulnier AI is simply a joy.

is instruction manual is designed to help you build a great ying aeroplane. Please

read this manual throughly before starting assembly of your 1/3 Scale Morane Saulnier AI

Use the parts listing below to indentify all parts.

If you are inexperienced with basic R/C ight we strongly recommend you contact your

R/C supplier and join your local R/C model Flying Club. R/C Model Flying Clubs oer a

variety of training procedures designed to help the new pilot on his way to successful R/C

ight. ey will also be able to advise on any insurance and safety regulations that may ap-

ply.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE

YOU ASSUME ALL RISK & REPONSIBILITY.

INTRODUCTION

WARNING

KIT CONTENTS

2 2

HINGING THE AILERON

Note : e control surfaces, including the ailer-

ons, elevators, and rudder, are prehinged with

hinges installed, but the hinges are not glued in

place. It is imperative that you properly adhere

the hinges in place per the steps that follow us-

ing a high-quality thin C/A glue.

Carefully remove the aileron from one of

the wing panels. Note the position of the

hinges.

Remove each hinge from the wing panel

and aileron and place a T-pin in the center

of each hinge. Slide each hinge into the wing

panel until the T-pin is snug against the wing

panel. is will help ensure an equal amount

of hinge is on either side of the hinge line

when the aileron is mounted to the aileron.

T-pin

Slide the wing panel on the aileron until

there is only a slight gap. e hinge is now

centered on the wing panel and aileron.

Remove the T-pins and snug the aileron

against the wing panel. A gap of 1/64” or

less should be maintained between the wing

panel and aileron.

Hinge

KIT CONTENTS

SEA 358 1/3 Scale Morane Saulnier AI

1. Fuselage

2. Wing set (3)

3. Tail set (2)

4. Canopy and Window

5. Cowling

6. Wing tube

7. landing gear

8. Fuel tank

9. Tail wheel

10. Ep Motor box

11. Pushrod set

12. Wing struts (2)

13. Gun

ADDITIONAL ITEMS REQUIRED

TOOLS & SUPPLIES NEEDED

in cyanoacrylate glue.

Medium cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

read-lock.

Paper towels.

�50-62cc gasoline engine.

�Computer radio 5 channel with 6

servos.

�Glow plug to suit engine.

�Propeller to suit engine.

�Protective foam rubber for radio

system.

1/3 ScaleMorane Saulnier AI Instruction Manual.

NOTE : e hinge is constructed of a spe-

cial material that allows the C/A to wick

or penetrate and distribute throughout

the hinge, securely bonding it to the wood

structure of the wing panel and aileron.

Deect the aileron and completely saturate

each hinge with thin C/A glue. e ailerons

front surface should lightly contact the wing

during this procedure. Ideally, when the

hinges are glued in place, a 1/64” gap or less

will be maintained throughout the lengh of

the aileron to the wing panel hinge line.

Turn the wing panel over and deect the

aileron in the opposite direction from the

opposite side. Apply thin C/A glue to each

hinge, making sure that the C/A penetrates

into both the aileron and wing panel.

Using C/A remover/debonder and a paper

towel, remove any excess C/A glue that may

have accumulated on the wing or in the

aileron hinge area.

Repeat this process with the other wing

panel, securely hinging the aileron in place.

Aer both ailerons are securely hinged,

rmly grasp the wing panel and aileron to

make sure the hinges are securely glued and

cannot be pulled out. Do this by carefully ap-

plying medium pressure, trying to separate

the aileron from the wing panel. Use caution

not to crush the wing structure.

Work the aileron up and down sev-

eral times to “work in” the hinges

and check for proper movement.

Note :

CA glue

Hinge

Locate the aileron and ap control horns.

e taller control horn is used for the ailer-

ons, and the shorter horn for the aps.

Use sandpaper to scu the bottom of the

aileron and ap control horns. Use a paper

towel and isopropyl alcohol to remove any

oils or debris from the control horns.

Check the t of the control horns to

the aileron and ap. ey should rest ush

against the control surface as shown.

INSTALL THE AILERONS

CONTROL HORN

Ailerons control horn

Place low-tack tape 1/32 inch (1mm)

from the control horn slot. is will pre-

vent epoxy from getting on the control

surface when the control horns are glued

in place.

Apply epoxy to the area of the control

horns that st into the slots. Use enough

epoxy so the control horns will be fully

bonded to the ed surfaces.

Remove the control horns from the

control surfaces. Apply epoxy to the slot

in the aileron and ap. Make sure the

epoxy gets into the slot for a good bond

between the surfaces and control horn.

Epoxy

1/3 ScaleMorane Saulnier AI Instruction Manual.

Before the epoxy fully cures, remove

the tape from around the control horn.

is will allow the epoxy to ow around

the control horn, creating a small let

between the control horn and surface for

a ished look and secure bond.

INSTALLING THE AILERON SERVOS

Because the size of servos dier, you

may need to adjust the size of the precut

opening in the mount. e notch in the

sides of the mount allow the servo lead to

pass through.

Place the servo between the mounting

blocks and space it from the hatch. Use a

pencil to mark the mounting hole loca-

tions on the blocks.

Use drill bit in a pin vise to drill the

mouting holes in the blocks.

Epoxy

20.0

Minimum servo spec.

Torque : 6.0V: 157.00 oz-in (11.31 kg-cm)

7.4V: 179.00 oz-in (12.89 kg-cm)

Apply 2-3 drops of thin C/A to each

of the mounting holes. Allow the C/A to

cure without using accelerator.

Use dental oss to secure the connec-

tion so they cannot become unplugged.

Secure the servo to the aileron hatch

using Phillips screwdriver and the screws

provided with the servo.

C/A glue

Apply 1-2 drops of thin C/A to each of

the mounting tabs. Allow the C/A to cure

without using accelerator.

C/A glue

Remove the string from the wing at the

servo location and use the tape to attach it

to the servo extension lead. Pull the lead

through the wing and remove the string.

10.

1/3 ScaleMorane Saulnier AI Instruction Manual.

Set the aileron hatch in place and use a

Phillips screw driver to install it with four

wood screws.

AILERON PUSHROD INSTALLATION

Please study images below.

75mm

M3 clevis M3 lock nut

M2.5x10mm

12.

13.

11.

INSTALLING THE FUSELAGE SERVOS

Because the size of servos dier, you

may need to adjust the size of the precut

opening in the mount. e notch in the

sides of the mount allow the servo lead to

pass through.

Install the rubber grommets and brass

collets into all servos. Test t the servos

into the fuselage servo mounts.

Secure the servos with the screws

provided with your radio system.

Insert the switch into the pre-cut hole

in the fuselage

Rudder servo arm

Elevator servo

3/32” Hole

Rudder servo

Elevator servo

Elevator servo arm

INSTALLING THE ENGINE SWITCH

Switch

INSTALLING THE MAIN LANDING

GEAR TO FUSELAGE

Please study images below.

Minimum servo spec.

Torque : 6.0V: 157.00 oz-in (11.31 kg-cm)

7.4V: 179.00 oz-in (12.89 kg-cm)

1/3 ScaleMorane Saulnier AI Instruction Manual.

4.8.

3.7.

5.9.

6.10.

ead locker glue

M4x20mm

Indice

Altri manuali Seagull Models Giocattolo

Seagull Models

Seagull Models Glasair Sportsman G2-2 Manuale utente

Seagull Models

Seagull Models Boomerang 40 Manuale utente

Seagull Models

Seagull Models YAK 54 Manuale utente

Seagull Models

Seagull Models SEA232 Manuale utente

Seagull Models

Seagull Models JUMPER 25 Manuale utente

Seagull Models

Seagull Models Gipsy Moth DH-60M Manuale utente

Seagull Models

Seagull Models SEA238 Manuale utente

Seagull Models

Seagull Models Zivko Edge 540 V3 Manuale utente

Seagull Models

Seagull Models Shoestring SEA143 Manuale utente

Seagull Models

Seagull Models ZLIN 50 Manuale utente

Seagull Models

Seagull Models JUMPER 25 Manuale utente

Seagull Models

Seagull Models SEA 94 Pilatus PC-9 Manuale utente

Seagull Models

Seagull Models Magic Bird EF1 RACER 40E PNP, 46" Manuale utente

Seagull Models

Seagull Models KA8-B Manuale utente

Seagull Models

Seagull Models 540 Manuale utente

Seagull Models

Seagull Models Swift 40 Manuale utente

Seagull Models

Seagull Models STEEN SKYBOLT N250SB 15CC Manuale utente

Seagull Models

Seagull Models 15CC Manuale utente

Seagull Models

Seagull Models DUAL ACE Manuale utente

Seagull Models

Seagull Models CURTISS P-40N WARHAWK Manuale utente

Seagull Models

Seagull Models P-47D Thunderbolt 60 Manuale utente

Seagull Models

Seagull Models CESSNA 152 Manuale utente

Seagull Models

Seagull Models P47 SNAFU Manuale utente

Seagull Models

Seagull Models SHOCK-CUB 35-55cc Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente