Sealey YK209F.V2 Manuale utente
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATIONS
1. SAFETY INSTRUCTIONS
2.1. GENERAL INFORMATION
Steel frame construction with hydraulic pump unit. Sliding hydraulic ram assembly
gives 176mm of lateral travel for off-centre pressing applications. Frame head fitted
with ram pressure gauge. Supplied with flat pressing plate/V-blocks.
1.1 GENERAL SAFETY
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
Maintain the press in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
Keep the press clean for best and safest performance.
Locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is
adequate lighting.
Ensure the workpiece is correctly secured before operating the press.
WARNING! Always wear approved eye or face protection when operating the press.
Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.
Keep hands and body clear of the work table when operating the press.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip steel toe-capped shoes/boots.
Keep children and unauthorised persons away from the working area.
DO NOT operate the press if any parts are missing as this may cause failure or possible personal injury.
DO NOT use to compress springs or any other item that could disengage and cause a potential hazard.
DO NOT stand directly in front of the loaded press and never leave a loaded press unattended.
DO NOT force the press to achieve a task it was not designed to perform.
DO NOT make any modifications to the press.
DO NOT adjust or tamper with the safety valve.
DO NOT exceed the rated capacity of the press.
DO NOT apply off centre loads.
DO NOT allow the workpiece or the arbor plates to fall from the press working bench.
DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
DO NOT operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.
When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.
WARNING! Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be
placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
DANGER! The press is top heavy. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam, or
lift direct with a forklift with the forks located under the top crossbeam. DO NOT use a pallet truck.
INSTRUCTIONS FOR:
HYDRAULIC PRESS 20TONNE
FLOOR TYPE
MODEL No: YK209F.V2
Model No: . . . . . . . . . . .YK209F
Capacity: . . . . . . . . . . . .20tonne
Ram Stroke: . . . . . . . . . .180mm
Ram Ø: . . . . . . . . . . . . .50mm
Lateral Ram Travel: . . . . . .176mm
Max Height Ram to Table:. . .912mm
Min Height Ram to Table: . . .35mm
Table Aperture: . . . . . . . .155mm
Working Table Depth: . . . . .175mm
Working Table Width: . . . . .510mm
Overall Height:. . . . . . . . .1619mm
Weight: . . . . . . . . . . . . .105kg
Safety Guard (Optional): . . .YKSG20
Original Language Version YK209F.V2 Issue: 1 - 05/07/13
© Jack Sealey Limited
3.1 YK209F.V2 20TONNE PRESS ASSEMBLY (use the exploded diagram Fig.4 as a guide to assembly as well as the diagrams
below).
3.1.1. The bed frame is put in the bottom of the crate for transport, fix it to the uprights using bed frame pin (9) and circlip (10).
3. ASSEMBLY
3.1.2. Attach the base section (1) and support pieces (3) to both the frame uprights, using bolt (2), washer (4), lock washer (5) and nut (6). Refer
tog.1.
3.1.3. Move the pump assembly to the outside of the post, secure using bolt (37) and washer (4), which held the pump to the inside of the post
duringtransit.Refertog.2.
3.1.4. Assemblethegaugetting(31)thenylonring(32),(whichtsbetweenthegaugeandthegaugettingseeg.4),andthegauge(33).
Twistthegaugeastightaspossibletopreventitfromleaking.Thenthegaugeandgaugettingarettedtothemanifold(24).
Fig.1 Fig.2
Fig.3
Fig.4
Original Language Version YK209F.V2 Issue: 1 - 05/07/13
© Jack Sealey Limited
Note: Maintenance and repair must only be carried out by a qualified person. Contact your Sealey dealer for details.
5.1. Always keep the press clean, dry and lubricate all moving parts at regular intervals.
5.2. When not in use always store in a dry location with the piston retracted.
5.3. Should you need to check or replace oil ensure piston is fully retracted. Remove the oil reservoir filler plug (47) and top up using Sealey
hydraulic jack oil. DO NOT use brake fluid. Contact your local Sealey dealer for details. After filling purge the system to remove any air.
5. MAINTENANCE
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE PRESS.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO SEALEY. Please telephone Sealey on 01284 757500 to obtain the address and phone number of your local
agent.
If product is under guarantee please contact your dealer.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the
product and the oil according to local regulations.
4.1. INSTALLATION.
4.1.1 Securely attach the press to a flat, firm, level surface taking into account clearance for working pieces.
DANGER! The press is top heavy. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam,
or lift direct with a forklift with the forks located under the top crossbeam. DO NOT use a pallet truck.
4.1.2 Purge hydraulic system before operating the press.
The hydraulic system may require purging in order to eliminate any air that may have built up during transit. Check the oil level and top
up if required, open the release valve by turning anti-clockwise and pump the handle several times. Repeat if necessary.
DANGER! Press is purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
ensure the workpiece is secured on the table to ensure loads that flex will not suddenly “give” causing danger to operator or damage to
component. Ensure you have read and understood chapter 1 safety instructions.
4.2. OPERATING INSTRUCTIONS.
4.2.1 Check that the release valve on the hydraulic unit is fully closed, ready for operation.
4.2.2 Locate the flat pressing plates or the v-blocks on to the bed frame, push down the locating pins to ensure the plates do not slip. Place
workpiece onto the plates and position the head of the hydraulic unit on the centre of the workpiece using an appropriate extension.
Note: Care must be taken to ensure the plates do not fall from the bed frame.
WARNING! DO NOT apply off centre loads.
4.2.3 When work is complete turn the release valve anti-clockwise to release the pressure and the piston and the ram head will retract
automatically. Note: Always keep the piston retracted after use.
4. INSTALLATION & OPERATING
Original Language Version YK209F.V2 Issue: 1 - 05/07/13
© Jack Sealey Limited
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE MACHINE.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.
If product is under guarantee please contact your dealer.
De-commissioning Product
Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the
product and the oil according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
Parts support is available for this product. To obtain a listing and/or diagram, please log on to: www.sealey.co.uk,
email: sales@sealey.co.uk or phone: 01284 757500
Indice
Altri manuali Sealey Utensili elettrici
Sealey
Sealey SA1001 Manuale utente
Sealey
Sealey SDL12 Manuale utente
Sealey
Sealey VS7026 Manuale utente
Sealey
Sealey GSA53 Manuale utente
Sealey
Sealey YKGS20 Manuale utente
Sealey
Sealey VS704.V2 Manuale utente
Sealey
Sealey SX500 Manuale utente
Sealey
Sealey YK15.V3 Manuale utente
Sealey
Sealey HS103K Manuale utente
Sealey
Sealey E540.V3 Manuale utente
Sealey
Sealey SD1530 Manuale utente
Sealey
Sealey SA630.V3 Manuale utente
Sealey
Sealey SDL7 Manuale utente
Sealey
Sealey SMS2002C Manuale utente
Sealey
Sealey BSL100.V2 Manuale utente
Sealey
Sealey GSA53 Manuale utente
Sealey
Sealey SA371 Manuale utente
Sealey
Sealey HCC08 Manuale utente
Sealey
Sealey HT106LED Manuale utente
Sealey
Sealey STW701 Manuale utente
