Sebatron VMPDualPlus Manuale utente
~Sebatron~
Innovative Australian Audio
VMPDualPlus - operating manual
Copyright Sebatron 2021
Valve Microphone Preamplifier with EQ
VMPDualPlus
1/Introduction
2/Features
3/Functions and Dials
4/Inputs and Outputs
5/Operation
6/General Maintenance
7/Specifications
Table of Contents:
The VMPDualPlus is a high quality two channel high voltage Valve
Microphone Preamplifier and Direct Input with a basic passive two band
shelving Equalizer on each channel.
As its name suggests the VMPDualPlus is a part of the Sebatron VMP
series of Valve Microphone Preamplifiers. Like its four channel counterpart,
the VMPQuadPlus, the VMPDualPlus is based around a transformer-coupled
microphone input and 12AT7 valve triode combination running on a proper
high tension voltage rail.
All circuitry is fully discrete and completely Class A. There are no
intergrated circuits or chips used in the design. This has the benefits of wide
sonic bandwidth for maximum audio frequency response and extra headroom to
ensure the dynamics of the signal remain intact.
Gain is adjusted via a six way Pad/Gain selector switch that controls
negative feedback around the first stage of the 12AT7 Valve. Gain steps are
evenly placed at 6db apart making the settings effective and easy to recall. The
adjustable gain range in conjunction with the pre-amp out control makes it
possible to use the preamp on virtually all sources from the very quiet to the
very loud. The VMPDualPlus handles all microphone types - Ribbon, Dynamic
and Condenser - with ease.
To sweeten signals the VMPDualPlus passive two band Equalizer is
extremely effective and an indispensable tool for sound manipulation.
The high frequency boost settings add clarity and sparkle to material
which would otherwise sound harsh or unnatural when boosted with
conventional digital EQ.
The low frequency boost settings add body and depth to thin signals in a
buttery manner that embellishes the signal by adding a distinct classic
character. Both bands have been configured to bring out the best in Valve
colouration by their chosen frequencies.
Running pre-recorded matrerial through the VMPDualPlus can also add
flavour and spark to otherwise dull or unexciting mixes.
Like all Sebatron products the VMPDualPlus is a musical vehicle that will take
you and your music on long sonic journeys.
1. Introduction
2. Features
• Transformer balanced XLR input feeding 12AT7 dual triode valve
• High Impedance unbalanced phono Direct Input for Guitar, Bass,
Keyboards or line level signals etc. on front panel for easy access
• Balanced phono TRS outputs for independent monitoring
• Fully balanced XLR main outputs
• Quality 12AT7/ecc81 Valve running on a High Voltage rail
providing crystal clear musical signal amplification
• Over 68db of gain variable from clean to coloured
• Six-way Pad/Gain control in 6db increments that sets the gain
and colour of the preamp
• Six-way High Shelf selector dealing high Frequency boost or cut
• Six-way Low Shelf selector dealing low Frequency boost or cut
• 180 degree Phase toggle switch to flip signal output phase
• +48 VDC Phantom Power for condenser microphones with LED
indication
• Green LED indicates signal is in correct operating range
• Output level control for transparent control of the final
output signal
• Solid build with 3mm mild steel powdercoated front panel and
1mm mild steel faceplate
• Switchable 110/120 - 220/240 VAC mains voltage selector
VMPDualPlus preamp
2. Features
(top row)
-Phantom Power Switch: Switchable +48V power for condenser microphones
-Signal LED: Illuminates when signal is present and in optimum range
-Pre-amp out: Adjusts final output level of preamp
-Normal/Reversed Phase Switch: Selects the phase or polarity of the signal
-Passive EQ High Selector: Six position selector switch for
high frequency cut or boost
(bottom row)
-Direct Input: 100k High Impedence Balanced/Unbalanced Phono input for
electric Bass, Guitars, Keyboards and line inputs
-Pad/Gain Selector: Acts as a pad and gain control by varying
negative feedback around first stage of Valve - set in 6db steps
-Passive EQ Low Selector: Six position selector switch for
low frequency cut or boost
3. Functions and Dials
3. Functions and Dials
Pad/Gain
The Pad/Gain selector has been designed to be used in conjunction with the
pre-amp out control to achieve the optimum recording level.
As the dial is turned to the right the signal increments by 6db and the flow to
the valve is increased allowing the onset of a mild harmonic distortion. This also
adds weight to the signal by subtley pushing peaks down and average levels up.
To compensate for the extra signal level when incrementing the Pad/Gain control to
the right the pre-amp out control is usually turned slightly to the left.
Passive EQ
The passive EQ has been designed to compliment existing digital EQ by utilizing
the positive attributes of the valve’s natural compression and colouration. This gives the
signal a ‘pleasant to the ear’ musical texture while still retaining the width and integrity of
the original signal.
The High band is subtle and sweet with smooth equalization curves at 6db boost
per octave. The increments are nonlinear with the initial step of approximately 1db
stretching out to over 4db on the bright setting.
On the outer settings there is some slight interaction with the gain control.
On the first two settings (air 1 and air 2) the boosted high frequencies start from 10khz.
The last boost setting (bright) is wider and has the frequency boosted from lower down at
around 4khz. In addition to the three high boost EQ settings there are two high cut
settings designed for use with vocals or instruments such as drums etc.
The Low band EQ circuitry is situated between the two triode stages of the valve.
This gives the lower EQ a specific coloured response that is slightly syrypy in nature.
All the settings are centred around a single low frequency with each setting varying the
amount of boost.
Like the High band EQ settings the Low band settings are not linearly or evenly
spaced. The steps get wider as the settings progress consequently adding colour
and an organic texture.
In addition to the three low boost EQ settings there are two low cut settings
designed for use with vocals or instruments such as acoustic guitar etc. These are 6db
per octave roll offs with the first setting -3db point at 80hz and second setting -3db point
at 120hz.
Channel 1 Output
Channel 1 Output/Input
Channel 2 Output/Input
Balanced TRS
Balanced XLR Balanced XLR
All XLR inputs and outputs are pin 1=shield, pin 2=hot (+), pin 3=cold (-).
All TRS outputs are Tip=hot, Ring=cold, Sleeve=ground/shield.
Channel 2 Output
Balanced TRS
4. Inputs and Outputs
Mains Power Input
Voltage Selector Switch
The VMPDualPlus can be switched between different global mains voltages via
the voltage mains selector on the back of the unit.
This switch is usually set in the factory for the appropriate voltage that the
unit is destined for, however, in cases of resale etc. it is always recommended to
check this switch before initial power up.
If Voltage Selector Switch is set to the wrong position the fuse should blow
before any damage occurs.
Fuse rating is 0.8 amp @ 240/250 volts (or 1.6 amp @ 110/120 volts).
4. Inputs and Outputs
General Tracking with Mic or Direct Input:
1./ Turn pre-amp out level control fully left, phase switch to normal, both EQ set to flat.
Set Pad/Gain six way selector to default 0db setting.
2./ Plug chosen microphone into XLR mic input socket on back.
If the microphone is of the condenser type then activate the Phantom Power switch
and observe phantom LED to confirm power.
3./ Observe green signal indication LED light when speaking or singing into the
microphone to confirm microphone signal.
4./ If more gain or colour is required then adjust six way Pad/Gain selector to suit.
5./ Adjust pre-amp output level to achieve optimum signal level.
Adjust equalization controls to taste.
5. Operation
Running pre-recorded tracks through the VMPDualPlus mic pre for colour:
Signals can be injected into either the XLR on the back or the Direct Input.
1./ Turn pre-amp output control fully left so there is no output.
Set Pad/Gain control to 0db, both EQ to flat, phase to normal and phantom power
to off.
2./ Plug external signal into XLR on back of unit or into Direct Input on front panel
using a balanced (TRS) or unbalanced phono cable.
We recommend using the front panel Direct Input as it is a direct path to the Valve
without the transformer colouration.
3./ With signal flowing slowly turn pre-amp output level up and monitor signal.
4./ Adjust Pad/Gain selector for more or less colour and adjust pre-amp output level
control for optimum reading on the recording unit (DAW etc.).
Adjust equalization controls to taste.
Altri manuali Sebatron Amplificatore
