Seco TANARO Series Manuale utente

Product Manual

TANARO x4 Mini 7.0 OF PCT 1K

Arm®Cortex®-A53 Panel Mount

PRODUCT MANUAL

TANARO

Document Revision History

The information in this document is subject to change without prior notice in order to improve reliability, design and

function and does not represent a commitment on the part of the manufacturer.

Online support on edge.seco.com

Revision Date Author Description

V 1 21.09.2021 CG Initial Release

V 2 17.12.2021 bmy SECO CI Update 2022

V 3 31.01.2022 MH

Text extension chapter IV. Approvals & weight

correction of the power supply in the technical

data

PRODUCT MANUAL

TANARO

Table of Contents

1. Introduction .........................................................................................4

2. Safety Hints .........................................................................................5

3. Product Introduction ..........................................................................7

3.1 Type Plate and Device Information ..............................................................7

3.2 Product Names and Variants........................................................................8

3.3 Related Documents and Online Support....................................................9

4. Technical Data .....................................................................................10

4.1 Block Diagram SBC .......................................................................................12

4.2 Connectors......................................................................................................13

5. Installation and Start Up .....................................................................15

5.1 Connection Scheme ......................................................................................15

5.2 Connecting the HMI device ..........................................................................16

6. Internal and External Interfaces.........................................................17

6.1 Gigabit Ethernet (U16)...................................................................................17

6.2 10/100 Mbps Ethernet (J20); Optional........................................................17

6.3 Power (J9) .......................................................................................................18

6.4 CAN/RS-485 Interface (J12).........................................................................19

6.5 USB Host 1 (J7)..............................................................................................20

6.6 USB Host 2 (J6)..............................................................................................20

6.7 USB Host 4 (J24, internal [not illustrated]) .................................................20

6.8 Speaker (J19) .................................................................................................20

6.9 RS-232/RS-232 (J10) ....................................................................................21

6.10 USB OTG (J5) .................................................................................................22

6.11 USB OTG Host (J3)........................................................................................22

6.12 SD Card Slot (X31) ........................................................................................22

6.13 Power LED (D36)............................................................................................23

6.14 Status LED (D22)............................................................................................23

6.15 Bootselect Switch (SW2) ..............................................................................23

6.16 Reset Switch (SW1) .......................................................................................23

6.17 Display LVDS (J13, J14)................................................................................24

6.18 Battery-Holder (BAT1)...................................................................................25

7. Battery .................................................................................................26

7.1 BatterySpecications....................................................................................26

7.2 Replacement of the Internal Battery ...........................................................27

7.3 Supercap.........................................................................................................27

Annex A: Technical Drawing...............................................................................28

Annex B: Quality and Incoming Inspections .....................................................29

B-1 Display and Touch..........................................................................................29

Annex C: Evaluation criteria of standard display module ................................30

Annex D: Hardware Revision Information .........................................................31

Annex E: Guidelines and Standards .................................................................32

E-1 RoHS Declaration...........................................................................................32

E-2 Supplier Declaration – Directive EG 1907/2006 REACH..........................32

E-3 ULCertication...............................................................................................32

E-4 SECO Northern Europe Conformity Statement.........................................33

Annex F: Common Documentation....................................................................34

F-1 Warranty hints.................................................................................................34

F-2 Field of Application.........................................................................................35

Annex G: Technical Support ..............................................................................36

Annex H: General Information ............................................................................37

* alternative assembly upon request

PRODUCT MANUAL

TANARO

1. Introduction

Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional

use and therefore we suppose extended technical knowledge and practice in working with such products.

The information in this manual is subject to technical changes, particularly as a result of continuous

product upgrades. Thus this manual only reflects the technical status of the products at the time

of printing. Before design-in the device into your or your customer’s product, please verify that this

document and the therein described specication is the latest revision and matches to the PCB

version. We highly recommend contacting our technical sales team prior to any activity of that kind.

The attached documentation does not entail any guarantee on the part of SECO Northern Europe

GmbH with respect to technical processes described in the manual or any product characteristics

set out in the manual. We do not accept any liability for any printing errors or other inaccuracies in

the manual unless it can be proven that we are aware of such errors or inaccuracies or that we are

unaware of these as a result of gross negligence and

SECO Northern Europe has failed to eliminate these errors or inaccuracies for this reason.

SECO Northern Europe GmbH expressly informs that this manual only contains a general

description of technical processes and instructions which may not be applicable in every individual

case. In cases of doubt, please contact our technical sales team.

In no event, SECO Northern Europe is liable for any direct, indirect, special, incidental or

consequential damages arising out of use or resulting from non-compliancy of therein conditions

and precautions, even if advised of the possibility of such damages.

Before using a device covered by this document, please carefully read

Annex „F-1 Warranty hints“

Annex „F-2 Field of Application“

Embedded systems are complex and sensitive electronic products. Please act carefully and ensure

that only qualied personnel will handle and use the device at the stage of development. In the

event of damage to the device caused by failure to observe the hints in this manual and on the

device (especially the safety instructions), SECO Northern Europe shall not be required to honour

the warranty even during the warranty period and shall be exempted from the statutory accident

liability obligation. Attempting to repair or modify the product also voids all warranty claims.

PRODUCT MANUAL

TANARO

2. Safety Hints

Please read this section carefully and observe the instructions for your own safety and correct use of the device.

Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded

systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this

condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.

I. General Handling

Don’t drop or strike the unit: The PCB, display and/or other parts might be damaged.

Keep away from water and other liquids, the unit is not protected against.

Operate the unit under electrical and environmental conditions according to the technical

specication.

The electrical installations in the room must correspond to the requirements of the local (country-

specic) regulations.

Take care that there are no cables, particularly power cables, in areas where persons can trip over

them.

Do not place the device in direct sunlight, near heat sources or in a damp place.

All plugs on the connection cables must be screwed or locked to the housing.

Repairs may only be carried out by qualied specialist personnel authorized by

SECO Northern Europe GmbH or their local distributors.

Maintenance or repair on the open device may only be carried out by qualied personnel

authorized by SECO Northern Europe GmbH which is aware of with the associated dangers.

II. Electricity

The embedded systems may only be opened in accordance with the description in this user’s

manual for

- replacing of the (rechargeable, where applicable) lithium battery and/or

- conguration of interfaces, where applicable

These procedures have to be carried-out only by qualied specialist personnel.

When accessing internal components the device must be switched off and disconnected from the

power source.

When purchased core or basic versions without protecting back cover, don’t touch the PCB directly

with your ngers. Especially these products need to be handled very carefully.

Don’t operate or handle the unit without typical ESD protection measures, such as ground

earthing.

Operate the unit according to the technical specication only.

III. Damage or Permanent Malfunction

It must be assumed that a safe operation is no longer possible, in case

-the device has visible damage or

-the display is dark or shows strange pattern for longer period

-the device doesn’t react after a reset

In these cases the device must be shut down and secured against further use

PRODUCT MANUAL

TANARO

IV. Approvals

The TANARO may be equipped with a certied transmitting module. Please check for your

application what country specic approvals you have to run through with your end-device before

you are allowed to sell it on the market and what markings you need to attach.

Only antennas with a maximum gain of up to 4,07 dBi may be connected to the integrated WLAN/

Bluetooth module WG221BL(-S) to be compliant with the RED Directive.

Cables connected to any USB port shall have a length of not more than 3 meters.

Contact our support, if you need to use a longer cable.

S/N: YY-WW

Made in Germany

25,4

50,5

Art.No.: 900-0000R

Model: TANARO

9-32 V ; 2,3-0,65 A

SECO Northern Europe article number

Product name and conguration

Serial number

Power ratings

Production date (week/year)

(Exemplary Illustration. It shows the TANARO 7.0" BX.)

PRODUCT MANUAL

TANARO

3. Product Introduction

This document is applicable for hardware revisions 1.1 or later of the TANARO series.

Please nd the hardware version grid in „Annex D: Hardware Revision Information“:

TANARO is an Embedded System to be used as human machine interface (HMI) in various applications. Please

refer to Annex „F-2 Field of Application“ for further information. The system is equipped with a large number of

industrial interfaces. A wide variety of options is available as well.

3.1 Type Plate and Device Information

Position of Typelabel

S/N: YY-WW

Made in Germany

25,4

50,5

Art.No.: 900-0000R

Model: TANARO

9-32 V ; 2,3-0,65 A

PRODUCT MANUAL

TANARO

For service and later identication of the device, the type plate contains important information.

3.2 Product Names and Variants

Product name denition:

TANARO <CPU> <7.0> <BX> <PCT> <IPS> <additional description> <Vx.y.z>

Explanation:

TANARO Product family name (invariable)

<CPU> x4 Mini (number of cores inside the i.MX8M Mini processor)

<7.0> Display size in inch

<BX>, <OF> mechanical design of enclosure

<PCT>, projected capacitive touch

<additional description> contains variants which are important to sales product description, i.e.

different memory capacities for RAM and/or eMMC

customer-specic reduced assembly

etc.

<Vx.y.z> revision of PCB layout

<x> describes major changes in form t and functions

<y> describes variants that are different in PCB layout and could affect the list of

critical components (UL LoCC).

<z> describes minor changes to PCB layout due to production optimization like

solder resist mask or drilling diameters.

Also minor changes in assembly of PCB and/or device which do NOT affect the

list of critical components (UL LoCC) due to unlisted components or declared

“interchangeable”.

PRODUCT MANUAL

TANARO

3.3 Related Documents and Online Support

OPERATING SYSTEMS

http://support.garz-fricke.com/projects/Tanaro/Linux-Yocto/Releases/yocto-dunfell-tanaro-overview.html

Linux Yocto Dunfell

https://bit.ly/3y3xEuB

Contains information about Linux BSP with development environment

Linux Embedded System Yocto (Codename: Dunfell, Version X) includes

rst information about the bootloader Flash-N-Go

CPU S M

CPU Type i.MX8M Mini Quad

Core Class Arm®Cortex®-A53

Core Clock 1,8 GHz

Features

Media Processing Engine (MPE) with NEON technology for SIMD: Floating Point Unit (FPU) Support of 64-bit

Arm® v8-A architecture A53: 32 KB L1 cache for instruction and 32 KB for data M4: 16 KB L1 cache for

instruction and 16 KB for data

512 KB unied L2 cache

HW Accelerators 3D GPU GC NanoUltra(OpenGL ES 2.0) 2D GPU GC320, 1080p60 H265, VP9 decoder, 1080p60 H264,

VP8 decoder, 1080p60 AVC/H.264 encoder, VP8 encoder

RTC +/-1,5 ppm at 0 - 50°C +/-30 ppm at 25°C

Secure Element A71CH

PCB Temperature Sensor +/-2°C at -25 - 100°C

Memory

eMMC Flash 4 GB MLC eMMC

RAM Standard 1 GB 32 bit LPDDR4

SD Card Slot 4 bit MMC/SDIO/SD/SDHC

Operating Systems

Supported OS Linux Dunfell

Communication Interfaces

Network 1x 10/100/1000 Mbps Ethernet (RJ-45)

1x 10/100 Mbps (RJ-45)

1x 10/100/1000 Mbps Ethernet (RJ-45)

USB 2.0 2x 480 Mbit/s Host (Type A)

1x 480 Mbit/s OTG (Type Micro-AB) 1

1x 480 Mbit/s Host (Type A)

1x 480 Mbit/s OTG (Type Micro-AB)

CAN Fieldbus / RS-485 1x CAN (ISO/DIS 11898) + 1x RS-485 galvanic isolated 1x RS-485

RS-232 2x RS-232 (RX/TX/CTS/RTS)

MDB 2 /1x MDB (Master / Slave optional) 3instead of 2nd external RS-232

N/A

Synchronous

Serial Interfaces I²C

Wireless Communication

Wireless WLAN 802.11 b/g/n; Bluetooth 4.2; Antenna: External

Audio

Speaker output 1x speaker (connector), 3,5W RMS (8Ω)

Audio Internal 1x speaker 0.3 W RMS (8Ω) parallel to external output

PRODUCT MANUAL

TANARO

This document contains operating system specic information. The following additional documentations are

available:

4. Technical Data

1 Mechanically the Micro-USB interface has not been designed for frequent contact operations. Please use an

Display and Touch

Size 7.0 inch / 177.8 mm

Resolution 1024 x 600 pixel

Brightness Typ. 500 cd/m2

Backlight Lifetime Typ. 30.000 h

Viewing Angle 85°, 85°, 85°, 85° (UDRL)

Color 24 bit (16.7M)

Touch projected capacitive multi touch

Touch Interface PCAP I²C

Backlight Interface +12 V, +5V, on/off, PWM

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Seco Hardware per computer

Seco

Seco SBC-D23 Manuale utente

Seco

Seco Smarc LEVY Manuale utente

Seco

Seco SBC-C90 Manuale utente

Seco

Seco Qseven ATLAS Manuale utente

Seco

Seco uQseven uQ7-962 Manuale utente

Seco

Seco Q7-C25 Manuale utente

Seco

Seco Qseven QUADMO747-E6 Series Manuale utente

Seco

Seco SE - PH2 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente