Securacom SEC8 Manuale utente

SEC8

8 Zone Intruder Alarm System

Installation Manual

Securacom

2 P0031-LI-01.00

Contents

1. System Overview ........................................... 4

System Configuration ............................................................. 4

Control Panel .......................................................................... 5

Remote Keypads .................................................................... 5

LED Remote Keypad.................................................................. 5

LCD Remote Keypad ................................................................. 5

ACM-NX ................................................................................... 5

USB-Link.................................................................................. 5

Upload/Download Software................................................... 5

2. Installation..................................................... 6

Installation Sequence............................................................. 6

Control Panel .......................................................................... 6

Mounting .................................................................................... 6

Wiring the Control Panel ........................................................... 6

Control Panel Layout ................................................................. 7

PCB Layout ................................................................................. 8

Connecting Devices to the Network ......................................... 9

Remote Keypads ..................................................................10

PCB Layouts .............................................................................10

Wiring Detection Devices .....................................................10

Normally Closed.......................................................................10

Normally Open .........................................................................10

Single EOL - N/C ......................................................................11

Double EOL...............................................................................11

Triple EOL .................................................................................11

Loudspeaker Connections ...................................................11

External Sounder/Strobe Connections................................12

TR ..............................................................................................12

0V..............................................................................................12

+12 ...........................................................................................12

Bell (1) ......................................................................................12

Strobe (2) .................................................................................12

Panel Outputs 1 - 5...............................................................12

Telephone Line Connections................................................12

Commissioning .....................................................................13

Power-Up Options Menu..........................................................13

3. Programming the Control Panel ................ 14

Introduction...........................................................................14

Exiting Engineer’s Program Mode........................................14

Menu Navigation and Data Entry.........................................15

LCD Navigation ........................................................................15

Selection List............................................................................15

Bit Toggle Selection .................................................................16

Number Entry ...........................................................................17

String Edit - Number Mode .....................................................17

String Edit - Text Mode ............................................................18

1. Zone Programming...........................................................18

Zone Type .................................................................................18

Zone Wiring ..............................................................................19

Zone Attributes ........................................................................19

Zone Bypass Options...............................................................20

Zone Chime ..............................................................................20

Zone Soak Test ........................................................................20

Zone Text..................................................................................20

Zone Link..................................................................................20

2. Arming Control..................................................................21

Arming Timers ......................................................................... 21

Arming Modes ......................................................................... 21

Arm Options 1.......................................................................... 21

Arm Options 2.......................................................................... 22

Arm Keyswitch Control............................................................ 22

Auto Arm/Disarm .................................................................... 22

3. System Configuration....................................................... 23

System Timers......................................................................... 23

System Counters ..................................................................... 23

Hardware - Volume Levels...................................................... 23

Hardware - Output Monitoring ............................................... 24

Hardware - Monitoring ............................................................ 24

Configuration ........................................................................... 24

Control Timers ......................................................................... 24

Banner Text ............................................................................. 25

Remote Control Labels ........................................................... 25

System Links ........................................................................... 25

4. Keypad Configuration ...................................................... 26

Keypad Options 1.................................................................... 26

Keypad Options 2.................................................................... 26

Keypad Sounds ....................................................................... 26

5. Reserved........................................................................... 26

6. Panel Outputs and Devices ............................................. 27

Panel Output Type................................................................... 27

Panel Output Attributes .......................................................... 27

Output Types ........................................................................... 27

00: Global ................................................................................ 27

Group 02: Control Timer......................................................... 28

Group 03: Remote Control ..................................................... 28

Group 04: Link Control ........................................................... 29

Group 20: Zone Mimic............................................................ 29

Group 30: Zone Alarm ............................................................ 29

Group 40: Zone Tamper ......................................................... 29

Group 50: Zone Masked......................................................... 30

Group 60: Zone Fault.............................................................. 30

Group 70: Zone Bypassed...................................................... 30

Group 80: User Access ........................................................... 30

Communication Port ............................................................... 30

GSM & SMS Centre................................................................. 30

IP Module................................................................................. 30

7. Onboard Communicator .................................................. 31

ARC 1-4: Telephone Number.................................................. 31

ARC 1-4: Account Number...................................................... 31

ARC 1-4: Protocol .................................................................... 31

ARC 1-4: Protocol Options ...................................................... 31

ARC 1-4: Call Sequence/Attempts......................................... 31

ARC 1-4: Reported Event Groups........................................... 31

ARC 1-4: Cancel on Success .................................................. 32

ARC 1-4: PSTN Pre-Dial Number............................................ 32

ARC 1-4: IP Address ................................................................ 32

ARC 1-4: IP Port Number ........................................................ 32

Options: Auto Test Call Period................................................ 32

Options: Auto Test Call Time .................................................. 32

Fast Format: Reporting Channels .......................................... 32

Fast Format: Restore Channels ............................................. 33

Fast Format: Open/Close Channels ...................................... 33

Channel Type........................................................................... 33

Channel Attributes .................................................................. 33

Speech Dialler: Telephone Numbers 1 and 2 ...................... 34

Speech Dialler: Dial Sequence .............................................. 34

P0031-LI-01.00 3

Speech Dialler: Trigger Type ...................................................34

UDL Options .............................................................................34

UDL Password ..........................................................................34

UDL Ring Count........................................................................34

Call-Back Number....................................................................34

UDL Dial Sequence..................................................................34

Remote IP Address ..................................................................35

Remote IP Port .........................................................................35

8. System Users....................................................................36

User Access Code ....................................................................36

User Type..................................................................................36

User Locked By ........................................................................36

User Name ...............................................................................36

User Link...................................................................................36

9. Utilities ..............................................................................37

Time and Date..........................................................................37

User Menus...........................................................................37

Away Arm A........................................................................37

Stay Arm 1 S......................................................................37

Stay Arm 2 2* ..................................................................37

Stay Arm 3 3* ..................................................................37

Walk Test 11* ................................................................37

Test Bell & Outputs 12* ................................................37

Do Test Call 13*.............................................................37

View Event Log 21* .......................................................37

Print Event Log 22* .......................................................37

Call UDL 23* ..................................................................37

Change Code 81* ..........................................................37

Program Mode 91* ....................................................... 37

Exit Menu 99* ............................................................... 37

Log Events ............................................................................ 38

LED Indications..................................................................... 40

Fault & Status Messages..................................................... 40

Resetting Faults & alarms ...................................................... 40

4. Specifications.............................................. 41

Control Panel ........................................................................ 41

Electrical .................................................................................. 41

Environmental ......................................................................... 41

Physical .................................................................................... 41

LED Remote Keypad ............................................................ 41

Electrical .................................................................................. 41

Environmental ......................................................................... 41

Physical .................................................................................... 41

LCD Remote Keypad ............................................................ 41

Electrical .................................................................................. 41

Environmental ......................................................................... 41

Physical .................................................................................... 41

Standards ............................................................................. 41

Safety ....................................................................................... 41

EMC .......................................................................................... 41

Security .................................................................................... 41

Warranty ............................................................................... 41

Notes..................................................................................... 42

Notes..................................................................................... 43

4 P0031-LI-01.00

1. System Overview

System Configuration

P0031-LI-01.00 5

Control Panel

The SEC8 control panel is an advanced intruder alarm system

with 8 on-board zones and on-board multi format communicator.

The system is ideally suited to domestic and small commercial

installations.

The control panel provides a multi-channel integrated speech

dialler. Voice messages are recorded via a touch tone telephone

or by using the UDL software package.

Remote arming and disarming and system control can also be

carried out by calling the protected premises with a touch-tone

telephone. On answering the incoming call you are greeted with a

voice prompted menu.

The system can be further enhanced by using the ACM-NX module

which provides both IP and X-10 connectivity. X-10 is a simple

home automation protocol that uses the existing mains wiring to

communicate with X-10 compatible devices via a XM10U

controller. Once the ACM-NX is installed, both the system and X-

10 devices can be controlled remotely using smart phone apps.

A choice of either LCD or LED remote keypads is available. Other

features include:

f8 programmable on-board zones

f8 user codes plus engineer code

f4 programmable outputs (1Amp rated)

fOn-board communicator/modem/speech dialler

fLocal or remote upload/download

f250 event log

fAdvanced system diagnostics

f1.2 Amp power supply

fCommunication port for accessories etc

fLoudspeaker output (uses output 4)

fFlash upgradable

Remote Keypads

The SEC8 will accept up to a maximum of 4 remote keypads. All

remote keypads require a 4-wire connection to the control panel

using standard alarm cable. The following remote keypad models

are available:

LED Remote Keypad

The LED keypad features a dual 7 segment display for displaying

zone status and system fault messages. A set of dedicated

system status LEDs for AC, Ready, Armed, Trouble, Bypass, Alert

and Alarm are also provided. Other features include:

f4-wire connection using standard alarm cable

fInternal sounder

fBacklit keyboard

LCD Remote Keypad

The LCD keypad features a 2 x 20 character blue display for

showing all zone status and system fault messages. A set of

dedicated system status LEDs for AC, Trouble and Alert are also

provided. Other features include:

f4-wire connection using standard alarm cable

fInternal sounder

fBacklit keyboard

ACM-NX

The ACM-NX is an IP based communicator and X-10 home

automation interface PCB module. Features include:

fEthernet connection to LAN/WAN

fRemote access via AlcoUDL or smart phone app

fAlarm reporting via LAN/WAN to PC based alarm receiver

fX-10 port for automating X-10 devices via XM10U/E

controller

fX-10 devices controlled via the system or smart phone app

fPCB module clips into the control panel housing

USB-Link

The USB-Link provides USB connectivity between the SEC8 and

the host computer. It is required when a direct connection is

required between the UDL software package and the SEC8

control panel.

Upload/Download Software

This Windows based software can be used to remotely or locally

program and diagnose the Securacom range of security systems.

Features include:

fSimple intuitive user interface

fLocal or remote via modem and IP

fSystem remote control

fAdvanced system diagnostics

fMulti language support

fSystem audit trail

6 P0031-LI-01.00

2. Installation

Installation Sequence

Before attempting to install the alarm system, read this section.

Once you have an overall understanding of the installation

sequence, carefully work through each step.

1. Design the Layout

Make a rough sketch of the premises to get an idea of where all

alarm detection devices, keypads and other modules are to be

located.

2. Mounting the Control Panel

The control panel must be mounted within the protected area

close to an unswitched AC power source and the incoming

telephone line.

You must complete all wiring before connecting the battery, or

applying AC to the panel.

3. Install the Remote Keypads

Mount the remote keypads at locations that are easily accessible

during entry and exit from the protected area. Connect the remote

keypads to the control panel.

4. Zone Wiring

Install detection devices and connect to control panel or

expander.

5. Other Wiring

Complete all other wiring including external/internal sounders

and telephone line connections.

6. Apply Power to the Control Panel

Once steps 1 to 5 are completed, apply power to the control

panel. First, connect the red battery lead to the positive terminal

and the black lead to negative. Then, connect the AC.

7. Program the System

If available use the UDL software package to program the system,

if this is not available program this system in accordance with the

procedures in Section 3.

8. Testing the System

Test the system thoroughly to ensure that all features and

functions are operating as required.

Control Panel

Mounting

Mount the control panel on a flat, plumb wall using at least three

appropriate screws. The rear casing has been designed with a

central key-hole slot so that mounting is possible without

removing the Printed Circuit Board (PCB).

The angled slot in the lower corner has been provided to allow the

panel to be levelled easily. If the PCB has to be removed, carefully

pull back the two front PCB securing clips, lift the front of the PCB

and slide it downward. To replace the PCB simply reverse the

above procedure.

It is essential to ensure that none of the fixing slots or cable

entries are accessible after fixing.

Mains cabling must be secured (e.g. with a cable tie) to one of the

anchor points provided.

Wiring the Control Panel

WARNING: ELECTRICITY CAN KILL

BEFORE connecting the control panel ALWAYS

disconnect the supply at the consumer unit.

If in ANY doubt consult a qualified electrician.

ONLY connect the mains supply to the mains terminal

block, NEVER connect the mains supply directly to the

PCB.

The system installation MUST be carried out in

accordance with the national safety standards, for

example EN 60950: 1992.

ALWAYS refer to National Wiring Regulations when

conducting installation.

An appropriate and readily accessible disconnection

device (e.g. an unswitched fused spur) MUST be

provided as part of the installation.

The disconnection device must NOT be fitted in a

flexible cord.

Where identification of the neutral in the mains supply

is NOT possible, a two-pole disconnection device MUST

be used.

The building mains supply MUST incorporate

appropriate short-circuit backup protection (e.g. a fuse

or circuit breaker) of High Breaking Capacity (HBC, at

least 1500A).

Use mains cable of adequate carrying capacity for the

rated current (i.e. at least 0.75mm2).

P0031-LI-01.00 7

Control Panel Layout

3 4 5

1. Main Printed Circuit Board (PCB)

The main PCB that provides the terminals connection to remote

keypads and detection devices, see PCB Layout on next page for

full details.

2. Mains Transformer

The mains transformer is housed under this protected area and

provides AC power to the main PCB.

3. Mains Connection

The AC Mains supply is connected to a 3 way Euro Type fused

terminal block, which is fitted with a 500mA fuse.

Fuse T500mA

To Power Supply

Module

4. Mains Supply Cable Entry

The mains supply cable must be routed into the control panel

housing via this cable entry.

5. Standby Battery

The system housing will accept a 12V 7Ah battery to provide

continued operation in the event of an AC mains failure. Connect

the red battery lead to the positive terminal of the battery and

then connect the black battery lead to the negative terminal.

The system will only become “live” when the AC supply is

connected or the “Battery On” pins are shorted.

Control Panel

Network

Battery

12V 7Ah

Sealed Lead Acid Battery

8 P0031-LI-01.00

PCB Layout

1 2 3 4 6

16 89

1. AC Input

The two wires from the transformer are connected to these

terminals and supply power the system.

2. Network Connections

The network terminals provide connections to the remote keypads

and zone expanders. The + and – terminals provide power whilst

the R and R terminals are the data signals.

3. Zone Inputs 1 to 8

Detection devices such as movement sensors, vibration and door

contacts are connected to the zone input terminals. There are

several ways in which to wire a detection device (see page 10).

Each zone is fully programmable, see page 18 for information on

programming zones.

4. Bell Tamper Return

This terminal is connected to the tamper return connection from

an external sounder unit. If it is not required link it to 0V.

5. Auxiliary 12V

These terminals provide auxiliary power for the external sounder

and detection devices that require 12V power, e.g., moment

sensors. The auxiliary output is protected by an auto resetting

fuse (PTC) rated at 1.1 Amp).

6. Panel Outputs 1 to 4

These are fully programmable high current (1 Amp), switched

negative supervised outputs. Panel outputs 1 and 2 default to bell

and strobe operation, but can be programmed for other functions

if required, see page 27 for programming details. Each output can

also be programmed for supervision monitoring, see page 24.

Panel output 4 defaults as speaker driver and is used for driving

16Ωextension loudspeakers (see page 11). If a loudspeaker

driver is not required it maybe used as a standard output.

7. Telephone Line Connections

Telephone line connections (see page 12).

8. Power/Status LED

On steady when either AC or standby battery is present. Flashes

when the on-board communicator is dialling or sending data.

9. Communication Port 1

A serial communication port is provided for local downloading and

for third party devices.

10. Battery On (Kick Start)

When powering the system from battery only, the “Battery On”

pins must be momentarily shorted together with a plain blade

screwdriver or similar to kick start the power supply into

operation.

11. Battery Connections

A 12V rechargeable battery must be connected to these two

terminals in order to provide continuous system operation in the

event of mains failure. The battery output is protected by an auto

resetting fuse (PTC) rated at 1.6 Amp.

12. Lid Tamper Switch

This switch detects when the cover is in position and the screw is

fully secured. The tamper is designed to activate when the screw

is undone.

P0031-LI-01.00 9

Connecting Devices to the Network

Before connecting devices to the control panel network, isolate

ALL power from the control panel (AC Mains & Battery). Do not

continue if there is still power present on the control panel.

Connecting devices with power still present on the

control panel may damage the device or control panel

and invalidate any warranty.

Remote keypads and zone expanders are all connected to the

same network terminals located at the bottom left hand corner of

the control panel and may be connected serially (daisy chain), in

parallel (star) or any combination of the two.

Network Connections

The network is made up of four terminals incorporating power and

data. To ensure correct operation, all four terminals on the device

must be connected to the corresponding terminals on the control

panel, or previous device. The table below shows each terminal

and its description:

+ +12V Supply

- 0V Supply

R Data Return

D Data I/O

Control Panel

Network

500 metres

Remote Keypad

Address = 1

12V

Remote Keypad

Address = 2

Remote Keypad

Address = 3

Remote Keypad

Address = 4

12V

Cable Type and Distances

For improved immunity to electrical noise, the use of screened 4

core cable is recommended. The screen should be twisted

together and wired into the (–) terminal at the control panel only.

The maximum recommended distance for devices when using

standard 7/0.2 alarm cable is:

f250m for each branch when using the star (parallel)

configuration

fWhen using a daisy chain (series) configuration the

maximum distance will depend on the number of devices

connected on the chain. The more devices that are

connected, the shorter the distance to the last device (this is

due to voltage drop in the cable)

Whichever method of wiring configuration is used, ensure that the

voltage between the ‘+’ and ‘–’ terminals at each device is no

lower than 10.0V when the system is running on the standby

battery.

Overcoming Voltage Drop

There are several ways to overcome voltage drop:

fUse thicker lower resistance cable. Standard 7/0.2 alarm

cable has a resistance of 8Ωper 100m

fDouble up on the power connections – this will require using

a 6 or 8-core cable rather than a 4-core cable

fInstall a power supply to power the device locally, remember

to common the two negative connections

Installing a Power Supply

When a power supply is installed, the 0V connections on the

power supply must be connected through to 0V on the control

panel and the +12V connection between the control panel and

the device must be disconnected (see figure below).

Control Panel

Network

500 metres

Remote Keypad

Address = 1

12V

Remote Keypad

Address = 2

Remote Keypad

Address = 3

Remote Keypad

Address = 4

12V

1km

Power Supply

12V

Disconnect +12V

from control panel

10 P0031-LI-01.00

Remote Keypads

PCB Layouts

2 1

LED Remote Keypad

LCD Remote Keypad

1. Network Connections

The remote keypad is connected to the network terminals located

at the bottom left hand side of the PCB.

2. Address Selection

Each remote keypad must be assigned a different address using

the Address selector. Move the jumper to the required position 1,

2, 3 or 4.

3. Tamper Switch

The lid tamper for each remote keypad can be enabled or

disabled if required. Please refer to page 26 for further details.

4. Piezo Sounder

The piezo sounder generates low level alarm, key press, and

warning tones. Each type of tone can be enabled or disabled for

each remote keypad, please refer to page 26 for further details.

Wiring Detection Devices

The SEC8 provides 8 zones for connecting detection devices such

as movement sensors and magnetic door contacts. Each zone is

fully programmable to allow for maximum flexibility (see page 18

for Zone Programming details). The program options for a zone

will also determine how the zone may be wired. The following

wiring options are available:

Normally Closed

This wiring configuration should be used when connecting

detection devices that only have a normally closed alarm output.

Connect the detector as shown below and ensure that the zone is

programmed for “Normally Closed” operation, see page 19.

Zx Com

Alarm

1 Detector

Alarm

2 Detectors

Normally Open

This wiring configuration should be used when connecting

detection devices that only have a normally open alarm output.

Connect the detector as shown below and ensure that the zone is

programmed for “Normally Open” operation, see page 19.

Zx Com

Alarm

1 Detector

2 Detectors

Alarm

Altri manuali per SEC8

Indice

Manuali Altro popolari di altre marche

GO Industries

GO Industries 38017 Manuale utente

Cissell

Cissell 30LBCMAN2 Manuale utente

RIDGID

RIDGID K-60SP Manuale utente

Gage Bilt

Gage Bilt GB751SH-5 Manuale utente

OVE

OVE SIERRA 60 Manuale utente

ReelCraft

ReelCraft 7800 OLB21 Manuale utente

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuale utente

ROBLIN

ROBLIN DROP Guida utente

EMG

EMG EMG-ACB BARREL Manuale di servizio

MiniSolar

MiniSolar MT-150 Manuale utente

Parkside

Parkside PSZ 250 B2 Manuale utente

ABB

ABB REM 610 Manuale del prodotto

Parkside

Parkside 55992 Manuale del proprietario

Skyjacker

Skyjacker F250 Manuale utente

IBM

IBM IBM SYSTEM Z Guida all'installazione

Grech Motors

Grech Motors G28 Manuale utente

NOVAK

NOVAK BATTERY CARE SHEET Guida

Telemotive

Telemotive blue PiraT Mini Guida utente