Securakey ENTRACOMP 26SA-SM Guida
ENTRACOMP®26SA
With Remote Open Input
User/Installation Manual
COPYRIGHT © 2007
SOUNDCRAFT INC.
TABLE OF CONTENTS
INTRODUCTION ............................................................................. 1
SETTING THE SYSTEM (FACILITY) CODE .................................. 3
PROGRAMMING THE ENTRACOMP®26SA ................................ 5
VALIDATING A SINGLE CARD ................................... 5
VALIDATING A BLOCK OF CARDS ............................ 6
VOIDING CARDS ........................................................ 7
SETTING THE LATCH TIMER....................................... 7
ACTIVE/INACTIVE......................................................... 7
DOOR UNLOCK MODE................................................. 8
TIMED ANTIPASSBACK FEATURE .............................. 8
ANTIPASSBACK WAITING TIME.................................. 9
RELAY CONFIGURATION........................................... 10
SecurRelayTM MODE.................................................... 10
INSTALLATION............................................................................. 11
WIRING INSTRUCTIONS ............................................................. 11
REMOTE OPEN........................................................... 14
SECURELAYTM ............................................................ 14
INSTALLATION INSTRUCTIONS ................................................. 15
SURFACE HOUSING TO SINGLE GANG
ELECTRICAL BOX ................................................. 15
SURFACE HOUSING WITHOUT
ELECTRICAL BOX ................................................. 15
SURFACE HOUSING WITH
POST MOUNT ........................................................ 16
SURFACE HOUSING WITH FLANGE MOUNT
ADAPTER ............................................................... 17
Secura Key • i
FLUSH MOUNT TO EXISTING 5S BOX..................... 20
FLUSH MOUNT WITH 5S BOX .................................. 21
FLUSH MOUNT WITHOUT 5S BOX........................... 22
METAL SURFACE HOUSING TO SINGLE GANG
ELECTRICAL BOX ............................................... 25
METAL SURFACE HOUSING WITHOUT
ELECTRICAL BOX ............................................... 25
METAL SURFACE HOUSING WITH POST
ADAPTER ............................................................. 26
METAL SURFACE HOUSING WITH FLANGE
ADAPTER ............................................................. 27
SPECIFICATIONS........................................................................ 30
V041007 3320389-E (6570)
Secura Key • ii
INTRODUCTION
The ENTRACOMP®26SA is a stand alone access control system that
will control access to a passageway for up to 65,503 individuals.
There are two kinds of cards used with the ENTRACOMP®26SA, access
cards and program cards.
Access cards are used by individuals to gain access to the passageway.
Each access card is magnetically encoded with two types of information:
the system code (or facility code) and the ID number. Your access cards
will all have the same system code, but each will have its own ID number.
Your unique system code is what prevents cards from other systems
from activating your unit. The ID number is what distinguishes one user
card from another.
NOTE: The 26SA can not recognize ID
numbers higher than 65,503.
Program cards are used to tell the ENTRACOMP®26SA what it is to do.
As with access cards, program cards are magnetically encoded with a
common system code and instruction information. The system code
of your program cards is the same as the system code of your access
cards. Your unique system code is what prevents program cards from
other systems from programming your system. There are 15 different
program cards. There are ten number cards (0 through 9) and five function
cards. The program cards are as follows:
Secura Key • 1
Secura Key • 2
“0” ZERO
“1” ONE
“2” TWO
“3” THREE
“4” FOUR
“5” FIVE
“6” SIX
“7” SEVEN
“8” EIGHT
“9” NINE
“VALID” VALIDATE
“VOID” VOID OR CANCEL
“*” THRU
“SET TIMER” SET LATCH TIMER OR
ANTIPASSBACK TIMER
“ACTIVE/INACTIVE” -ACTIVATE OR INACTIVATE SYSTEM
SETTING THE SYSTEM (FACILITY) CODE
When received, the correct system code may already be set. Should it
become necessary to reset the system code, remove the unit from the
wall to gain access to the reset button (see figure 1). Momentarily depress
the reset button. The LED indicator will flash red and green alternately
(If at power up, the LED is already flashing red/green, it is not necessary
to remove the unit from the wall and press the reset button). While the
LED indicator is flashing, place either a programming card or an access
card with the proper system code onto the touch plate and after the LED
turns solid Green, remove it. The ENTRACOMP®26SA will “remember”
the system code and retain it until reprogrammed. If the reset button is
pushed, but no card is placed on the TOUCH CARD®reader plate before
the LED indicator times out, the system code will be unchanged. Wait
for the LED indicator to time out before programming the unit.
There may occur situations which require the unit to recognize more
than one system (facility) code. The ENTRACOMP®26SA can be set
to recognize up to ten (10) different system codes. To program multiple
system codes, follow the procedure above for programming a single
system code, but place a card with the second system code (and third
system code if necessary) on the TOUCH CARD®reader plate before the
red/green LED indicator times out. When more than one facility code
has been programmed, the unit will not distinguish between cards
having different facility codes but the same ID number.
Secura Key • 3
FIGURE 1
Secura Key • 4
PROGRAMMING THE ENTRACOMP®26SA
Functions of the ENTRACOMP®26SA are programmed by placing the
program cards on the TOUCH CARD®reader plate in a proper sequence.
It is helpful to think of placing a program card on the TOUCH CARD®
reader plate as depressing a key on a keyboard or key pad. You may
begin programming at any time by placing the first program card of the
sequence on the TOUCH CARD®reader plate. At this point the LED
indicator will show an amber color. When you remove the program card
from the TOUCH CARD®reader plate, the LED indicator will flash the
amber color awaiting the next program card. Placement of the next
program card on the TOUCH CARD®reader plate causes the amber
LED to stop flashing and become solid. In like manner, the remainder
of the program cards for the programming sequence are placed on the
TOUCH CARD®reader plate. At the end of the programming sequence,
the LED indicator will flash green to indicate that the programming
instruction has been accepted. While programming, it is necessary
to place the next card of the sequence on the TOUCH CARD®reader
plate while the LED indicator is flashing amber (you have approximately
10 seconds between each card). If the amber LED times out, it will be
necessary to restart the programming sequence. Should an error be
made in the programming sequence, the LED indicator will flash red
instead of green.
VALIDATING A SINGLE CARD. To validate a single card, place the
sequence of program cards representing the card number on the
TOUCH CARD®reader plate and then place the “VALID” card on
the TOUCH CARD®reader plate.
Secura Key • 5
Example: Validate card number 100.
Place the “1” card on the TOUCH CARD®reader plate, remove it and place
the “0” card on the TOUCH CARD®reader plate, remove it and place again
the “0” card on the TOUCH CARD®reader plate, remove it and place the
“VALID” card on the TOUCH CARD®reader plate, and remove it.
1 + 0 + 0 + VALID
VALIDATING A BLOCK OF CARDS. To validate a block (continuous
sequence) of cards, place the sequence of cards representing the first
card number of the block on the TOUCH CARD®reader plate, then the
“*” (THRU) card, then the sequence of cards representing the last card
number of the block, and then place the “VALID” card on the TOUCH
CARD®reader plate.
Example: Validate cards 5 thru 225.
NOTE: After a block Validate or Void is complete, the LED will turn
Green. Then the reader will beep and the LED will turn off.
Place the “5” card on the TOUCH CARD®reader plate, remove it and place
the “*” (THRU) card on the TOUCH CARD®reader plate, remove it and
place the “2” card on the TOUCH CARD®reader plate, remove it and again
place the “2” card on the TOUCH CARD®reader plate, remove it and place
the “5” card on the TOUCH CARD®reader plate, remove it and place the
“VALID” card on the TOUCH CARD®reader plate, and remove it.
5 + *+ 2 + 2 + 5 + VALID
Secura Key • 6
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Securakey Lettore di schede
