Secure 2 Series Istruzioni operative
Single Channel 7 Day Timeswitch
ChannelPlus H17XL Series 2
User Operating Instructions
2
The ChannelPlus H17XL is a single channel timeswitch allowing
up to 3 On / Off settings per day for each day of the week.For day
to day operation the H17XL has a manual 1 or 2 hour boost button
as well as an advance button to bring forward the next
programmed operation. The back lit display, automatic clock and
menu driven programming are all features designed to make the
operation of the ChannelPlus H17XL as simple as possible to
use.
The ChannelPlus family of electronic programmers offer a range
of advanced features coupled with simplified 'menu driven'
programming all designed to help save energy.
ChannelPlus H17XL
The ChannelPlus H17XL Timeswitch
The simple instructions contained in this user guide are designed
to help with the programming and operation of the unit. Most of
the following instructions require the front flap to be lowered.
Please replace the flap when normal operation is required.
8 BOOST and COPY button (Illuminated When Active)
13 Front Flap (Lowered)
1 Current time of day
3 Channel Heading
6 Channel ON indicator
9 PLUS button
5 Next On / Off time
10 MINUS button
12 SET button (Coloured Green)
11 Programme Select buttons (Coloured Blue)
7 ADVANCE and ENTER button (Illuminated When Active)
2 Day of week and date
4 Current Channel programme
3
PRODUCT OVERVIEW - DETAIL SHOWN WITH
THE FLAP LOWERED
1
9
10
11
4
3
5
6
7
12
8
13
2
HTG
Time of Day
timeswitch has a fully graphical,
back-lit display. The information
displayed will change depending
upon the settings made and which
mode you are in. During different
programming modes and / or
setting screens the current time,
day / date, holiday indicator will
only appear when necessary, this
is to reduce confusion during the
programming process. This is explained further in later sections
of this guide.
The display will illuminate for approximately 1 minute whenever a
button is pressed. To illuminate the display for viewing purposes
only press the green set button under the front flap twice.
When setting or adjusting, the timeswitch will automatically
return to the running mode if no buttons are pressed for
approximately 1 minute. If the setting or adjusting has not been
finished, please start the procedure again.
The ChannelPlus H17XL incorporates a factory set clock and
calendar which means that no adjustments should be necessary
to the time of day and BST / GMT time changes take place
automatically. If adjustments are required please refer to page 11
of this booklet.
The ChannelPlus H17XL
Activating the Back-lit Display
Setting and Adjusting
Display Information
4
10:42 FRI
24 JAN
HTG
All day
On untill
22.30
Holiday
function
active
Day
Date
Time
Channel /
Zone status
Channel
header
Manual Overrides
Boost Function - 1 Or 2 Hour Temporary Override
The boost facility will allow the user to either activate a channel
which is currently ‘OFF’ for 1 or 2 hours, or to extend a current ‘on ’
period by 1 or 2 hours. To indicate the boost being activated the
‘BOOST’ button under the selected channel will stay illuminated
for the duration of the boost / extension period. The display will
also indicate the extension to the time visually on the screen.
5
Press BOOST
button once:
Your system
will be boosted
for 1 hour
Press BOOST
button twice:
Your system
will be boosted
for 2 hours
Press BOOST
button a third
time to cancel the
period and return
to the normal
programme
Advance Function - Brings Forward The Next On or Off
Operation
The advance facility will allow the user to either bring a timeswitch
'ON' which is currently 'OFF' or switch a timeswitch 'OFF' which is
currently 'ON'. To indicate the advance feature being activated
the 'ADVANCE' button will stay illuminated until the next
programme switching time, the user display will change to also
indicate the status of the timeswitch and the next switching time.
Press ADVANCE
button once to
move to the next
ON / OFF time
To cancel the advance press
the ADVANCE button again.
This will return the unit to its
normal programme
Programme Override Facilities
With the ChannelPlus H17XL timeswitch operating in the normal
running mode it is possible to alter the functionality of the
programme by means of the blue 'select' buttons under the front
flap.
The options include;
OFF - Timeswitch output will be constantly ‘OFF’, there is
the ability to turn off heating during summer without
altering the programme times. 1 or 2 hour boost still
available.
The diagram below illustrates how to alter the setting, it assumes
that the Timeswitch is in the AUTO mode to begin with.
ALL DAY - Timeswitch output operates from 1st ‘ON’ time until
3rd ’OFF’, ignoring all switching times in between.
All of the settings above will be permanent, i.e. unaffected by
programme times, until alteration by the user.
AUTO - Timeswitch output follows all programmed ‘ON’ and
‘OFF’ times.
ON - Timeswitch output will be constantly ‘ON’.
6
Press SELECT
once.
Programme
goes from AUTO
to ALL DAY
Press SELECT
again.
Programme
goes from ALL
DAY to ON
Press SELECT
again.
Programme
goes from
ON to OFF
Press SELECT
again.
Programme
goes from
OFF to AUTO
Timeswitch will
operate from
first ON until
last OFF period
Timeswitch will
be continuously
ON
Timeswitch will
be continuously
OFF
Programme will
return to
normal ON and
OFF times
Setting the Programme Times
The programme times have been preset as shown in the chart
below.
7
Default Time Settings - AM/PM
1st ON 1st OFF 2nd ON 2nd OFF 3rd ON 3rd OFF
Mon-Fri 6:30AM 8:30AM 12:00PM 12:00PM 4:30PM 10:30PM
Sat/Sun 7:30AM 10:00AM 12:00PM 12:00PM 5:00PM 11:00PM
If any changes are required to the programme times please
complete the operation as described in the flowchart below.
Press the green
‘SET’ button
Use the ‘+’ and ‘-’
buttons to select
required day
Repeat process for the
2nd and 3rd time settings
Use the ‘+’ and ‘-’
buttons to adjust
required ON time
If you require this programme
on any other day of the week
use ‘+’ and ‘-’ buttons to
select day and copy
Open cover
Press ‘ENTER’
Press ‘ENTER’
Press ‘ENTER’
Press ‘ENTER’
Programme the
remaining days
Press the green
‘SET’ button
Press the green
‘SET’ button Close cover
Adjust OFF time
Select
‘Set ON/OFF times’
Sample Displays
Select ‘SET ON / OFF times’
SET ON / OFF TIMES
SET HOLIDAY MODE
SET DEFAULTS
Select the day to set
FOR
SET ON / OFF TIMES
WEDNESDAYS
Enter the required on and off times
ON 06.30 ON 12.00 ON 16.30
PERIOD 1 PERIOD 2 PERIOD 3
OFF 08.30 OFF 12.00 OFF 22.30
SETTING ON / OFF TIMES
When carrying out any alterations to the programmed times and
settings the programmer will return to its normal run mode in 1
minute if no adjustments are made in that time.
Adjusting Settings
8
N.B. Do not use the holiday
p r o g r a m m e w h e n
conditions are such that
frost damage to the
heating system is possible
(unless a frost protection
thermostat is fitted to your
system).
P LE A S E N O TE : A n y
alteration to the current time
or date will cancel any
Holiday programme set.
Setting the Holiday Mode
The holiday mode can be used to suspend the program function
of the ChannelPlus timeswitch, it can be set in advance of your
departure date and for as long a period as required. The holiday
function operates from mid-day to mid-day, this means it can be
easily set to ensure your home is warm for your return. When the
holiday mode has been set a smiley face will appear on the
display. When the holiday mode is active only the day/date and
smiley face will be displayed. To cancel an active holiday period
please press any of the Select buttons under the front flap.
Open cover
Press the green
‘SET’ button
Use the + and -
button to select
‘HOLIDAY MODE’
Press ‘ENTER’
Use the + and -
button to adjust
START DATE
Press ‘ENTER’ Use the + and -
button to adjust
START MONTH
Press ‘ENTER’
Use the + and -
button to adjust
START YEAR
Press ‘ENTER’ Repeat process
for end period
Press ‘ENTER’
Press the green
‘SET’ button
Press the green
‘SET’ button Close cover
Sample Display
Enter holiday dates
1 SEPT 2014
SETTING HOLIDAY MODE
START AT MID-DAY ON
FINISH AT MID-DAY ON
21 SEPT 2014
Display when holiday mode is set
THURS 18 SEPT 9
The ChannelPlus H17XL has a number of default settings which
are normally installed. These settings are designed to reduce the
need for user intervention upon installation of the timeswitch.
However it is possible to customise the user display by following
the procedures in the following pages. The factory default
normally installed are illustrated below;
Adjusting Default Settings
Time and Date Clock Options Headings
are factory set
Time and calendar Time displayed in
24hr clock format i.e. Heating, Hot Water
or None
Channel heading set
to standard installation
10:42 FRIDAY
24 MAR 22:42
Options Options Options
The timeswitch has
been set with the
current time and date
during manufacture.
No alteration should be
required to the time and
date. However, if any
modification is required
please refer to the
flowchart on page 11
24 hour
AM / PM
or Water
Heating
None
10
HTG
ALL DAY
Off until
22.30
FRIDAY
24 MAR
HTG
ALL DAY
Off until
22.30
10:42 FRIDAY
24 MAR
HTG
ALL DAY
Off until
22.30
Questo manuale è adatto per i seguenti modelli
1
Indice
