Securefast AML2C Manuale utente

T/AML2C/080

28th November 2019

Before Setup

 Remove the Backplate from the Doorbell, unclip the baery

cover and remove the baery.

 There is a clear plasc lm over the top of each baery.

Remove the lms and replace the baeries.

 Connect the supplied USB Lead to the device and charge for 8

hours.

(This will require a 5V USB Mains Plug—not supplied)

Important: The product may power up when the baeries are rst

inserted; however, the device will not funcon correctly during the

installaon procedure unless it has been fully charged.

 Download the iCSee App (NOT iCSee Pro) to your phone by

searching in the App Store or by scanning the QR Code below.

 Turn o Mobile data (3G/4G) and connect to the available Wi.

Important: When seng up the iCSee app you

should allow any permissions it requests as

declining them may prevent the app from

funconing correctly; the screenshot displayed

on the le shows what permissions are

required.

T/AML2C/080

28th November 2019

Blue light solid - Startup

Blue light ashing - App remote monitor and setup

Red light ashing - Low baery

Doorbell Light Indicators

1) Registering for an Account

N.B: Local Login will allow you to have Temporary Access to the App as a Visitor- you can set up

devices but you will not have access to all the funcons.

a) Tap on “Sign Up” and complete the elds with the required informaon

Username – Must be unique. If rejected try a dierent one

Password – You will be prompted for the right number of upper case, lower case and numbers

Conrm password – Must match above

Email address – Used to reset passwords and for registraon

b) Tap on “Get Code” buon

c) Input the code you receive via email

d) Agree to the privacy statement

Camera

RESET

Buon

Bell Buon

Microphone

PIR Sensor

Indicator

USB Charging

Port

Micro SD

Memory

Card Slot

T/AML2C/080

28th November 2019

2) Add a device

 Aer charging the device for 8 hours press the Bell Buon to wake-up the Doorbell. The voice

Prompt “Wait to be congured” should be heard before proceeding to adding the device as

below.

N.B: If the above voice prompt is not heard wake-up the Doorbell, using the Bell Buon, then press

and hold the RESET buon. Release the reset buon when the voice prompt “Restore factory

sengs please don’t power o” begins.

Once the device is reset to its default conguraon the voice prompt “Wait to be congured”

should be heard when waking the device.

a) Open iCSee and register for an account if you

haven't already.

a) Tap the add symbol on the top right of the screen

b) Select “Set Up My Device To Wi Fi”

c) Input the name and password for the Wi Fi network

you are connected to, this is the one that the device

will connect to.

d) You will then be directed to the search screen

N.B: On the search screen a QR code can be displayed if you

tap the icon in the top right corner. Displaying this QR Code

to the Doorbell’s Camera can speed up the

Conguraon process.

T/AML2C/080

28th November 2019

e) When the device has successfully connected it will prompt you by saying “ Connected to

router successfully” you will then be asked to set a password for the device.

f) When the password is set you will be asked to give the device a name, this is what it will

appear as in the app.

g) You will be directed to the devices screen where you can view the device state and select

to view its feed.

Further Informaon

 The device has an esmated baery life of 6 months based on

10 minutes of operaon a day. The unit will enter a “sleep”

state to conserve baery; to “wake” the device, remotely,

simply tap the feed of the device you want to wake.

 If a device goes “oine” pull the screen down on the device

page to refresh the feeds

 To enable the camera to record events a Micro SD Memory

Card must be inserted into the device, the card may require

formang. This can be done by going on to the Device’s

Sengs and then “Storage Management” and then tap

“Format SD Card”

N.B: When the memory card is full new recordings/images will over-

write the oldest recordings/images.

front door

T/AML2C/080

28th November 2019

3) Features of the app

1) Data connecon speed

2) Signal strength and date/me

3) Baery/SD card status

4) Mute/unmute buon, allows you to hear

sound from the doorbell

5) Video quality FHD/SD, allows you to change

between high and standard denion video

6) Screen resoluon

7) Record video (4 seconds minimum) you can

then share the recording to others via the

pop up on the feed stang “Interesng Vid-

eo, click here to share”

8) Fullscreen

9) Playback feature. This allows you to play

back recorded videos and photos from local

storage or the cloud service. *For local stor-

age a Micro SD card (not included) needs to

be inserted into the camera

10) Intercom- Press and hold this icon to speak

through the doorbell via the app

11) Screenshot an image of feed you can then

share the recording to others via the pop up

on the feed stang “Nice Picture, click here

to share”

12) Sengs buon to access and congure

various features of the device.

N.B: Changes must be saved to be eecve

Avoiding excessive moon detecon alerts

If the alerts/nocaons from the PIR moon detecon are causing an issue do not turn o the “Alerts”

under “Alert and Message” or the Doorbell will not call your phone when the Bell Buon is pressed.

You can turn o the PIR moon detecon funcon by turning “Human Detecon” o and saving the

seng. This will enable you to receive calls but not get the constant alarms.

You can also set Time Periods that the PIR moon Detecon will be acve i.e if your device sends false

alerts when the sun shines directly on it between 3-4pm then you could set Time Periods of “Start 16.00”

and “End 15:00”so the PIR Moon detecon is not operang between 3 and 4 pm. (Days of the week this

is applicable can also be congured)

Alternavely, you can also increase the “Hover Detecon Time” and “Message Push Interval” in

“Advanced Sengs”. This will not only prolong baery life but will also rene the events that can cause

unnecessary alerts/nocaons from passing/irrelevant triggers.

548

910

T/AML2C/080

28th November 2019

5) Sharing or Adding Addional Devices

a) To add an addional device simply repeat the procedure aer

tapping the “+” icon

b) To add a shared device you must select the “Add Shared De-

vice” and input the Serial Number or Scan the QR Code of the

device being shared. Both can be found under the Device’s

Sengs and “About”.

c) To send a share invite via whatsap, text or email, click the share

icon under the device feed and select the relevant opon and

individual’s contact details. This will send the individual a link

with the serial number informaon that can be copied and

pasted in to the eld on the add shared device screen below .

N.B: You will also need the password the device was inially set up

with to successfully install a shared device and access the

device feed.

4) Installing the Device

Important: The Doorbell should be posioned to prevent excessive exposure to direct sunlight as this

could negavely aect the performance of the PIR moon detecon sensor.

a) Decide on device posioning considering the above; the unit is supplied with wood screws, wall

plugs and 3M double sided backing to suit a variety of installaons; therefore, select the most ap-

propriate method to x the Backplate of the Doorbell in the desired locaon.

b) Once the Backplate is mounted place the Doorbell on to it and secure the two together via the

hole in the base of the doorbell using the supplied machine screw and a Philips head screwdriver.

T/AML2C/080

28th November 2019

6) Further Informaon and Frequently Asked Quesons

 The Doorbell will emit a sound when the Bell

Buon is pressed to inform the person ringing the

Doorbell that the Device has registered the buon

being pressed. To turn this feature o, you will need

to turn on “Device Hints” under “Alert and Mes-

sage”.

 To alter the order your devices appear on your

device feed tap the buon in the top le corner

to alter the view and list your devices. If you then

tap the icon with an upward arrow next to the “+”

for add new device. You can now move and

rearrange the order of the devices using the 3

lines next to each device feed.

 What GB Memory Card can this device support?

The product is compable with a Micro SD card up to 32 GB.

 Why is my device oine/wont wake up?

Have you refreshed the device page by pulling the screen down and releasing?

The Device may have low baery and need charging.

Check other products on your Wi to determine whether your Wi is working.

Does the Wi have adequate signal strength where the Device is located? Try moving the

product closer to the Wi router to check this.

Reset the Device and recongure to Wi if all opons have been exhausted.

 How do I congure the Doorbell to a dierent Wi Network?

The Device must be woken up using the Bell Buon and then RESET by holding the Reset buon on

the reverse unl the voice prompt “Restore factory sengs please don’t power o” begins.

 Why does the Doorbell not respond when the Reset buon is pressed?

Have you woken the Doorbell using the Bell Buon rst? Are you holding the Reset Buon for at

least 5 seconds? If yes, remove baeries and let the unit power down, reinsert baeries let the unit

power up and congure to Wi and then try again.

T/AML2C/080

28th November 2019

8) Features of the Chime

Sound Selecon

The Chime has a library of 52 dierent sounds, to select a sound simply press the selecon buon to

cycle forwards and backwards through the library unl you nd the one you like.

If you decide you want to change your Chime you must repeat the process of Seng up the Chime

Volume

Press the volume buon to cycle through four levels of volume, the lowest being silent.

Connecng Mulple Doorbells

To connect mulple Doorbells simply repeat the connecon process for each doorbell required

Connecng Mulple Chimes (Max 5)

Repeat the above process on each chime to be paired with the doorbell

Dierent Sounds For Dierent Doorbells

Simply choose a sound and connect a Doorbell, then choose a dierent sound and pair the next Doorbell

Clearing The Chime’s Memory

To clear the chime’s memory un-plug it, then hold the volume buon whilst plugging it back in and

connue to hold it unl the light blinks (approximately 10 seconds).

Unit 6, Cedars Business Centre, Avon Road,

Cannock, Staffordshire, England

WS11 1QJ

Tel: +44 (0)1543 501 600 Sales: +44 (0)1704 502 810 Email:[email protected] Web:www.securefast.co.uk

Volume buon

Indicator

Select buon

7) Seng up a Chime

a) To set the chime up plug it into a mains

socket

b) Use the select buons to cycle through

the Chime library and stop when you

have found a Chime you like.

c) Hold down the volume buon unl the

indicator is a solid blue

d) Press the buon on the doorbell and the

chime will begin playing the sound

indicang a successful connecon.

a) Press the doorbell buon again and it

will play the selected sound

Indice

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente