Seeworld S03C Manuale utente
GPS Vehicle tracker
User manual S03C
(Version V2.0)
1.Accessories
Standard accessories:
1pc Charger
1pc USB cable
1pc Battery 5200mAh
1pc English Manual
S03C Product Description
GPS vehicle tracker
Geo-fence
Vibration alarm
Voice monitoring
With high intense magnet in its rear cover
Low power alarm
Battery with large capacity
SOS emergency alarm
Power-saving mode and avoid static drifting
Specification
GSM: MTK6223D
GSM :850/ 900/ 1800/ 1900 MHz
Build in GPS/GSM antenna
GPRS :Class12, TCP/IP build in GSM module
GPS Channels :20
Tracking sensitivity :-159dBm/-160dBm
Aquisition sensitivity: -144dBm/-147dBm
Locating time cost: Hot start: <1 sec(open sky)
Warm start: 35 sec on average
Cold start: 35 sec on average(open sky)
GPS antenna Built-in high sensitive omni antenna
LED indicators three LED indicators GPS-blue GSM-green Power-red
Button: Power on/off button
Battery :3.7vDC/ 5200mAh, longest work time: 30days,standby time: 45days.
Weight: 390g
Dimesion :91.5(L)×60.0(W)×38.0(H)mm
1. Appearance
2.1 LED status (non-sleep mode)
2.1.1Red LED (Power/working status)
LED Status
Indication
Flash quickly (interval 0.1S)
Low battery
Flash slowly (interval 2s)
Full charge/Working
normally
Flash slowly (Flash 0.1s after
every 2s)
Working normally
Bright
Charging
Dark
Out of battery / Troubleshot
2.1.2 Blue LED（GPS signal status）
LED Status
Indication
Flash quickly (interval 0.1s)
Searching GPS signal
Flash slowly (Flash 0.1s after
every 2s)
GPS signal has been
acquired successfully
Dark
GPS stops working
2.1.3 Green LED (GSM signal status)
LED Status
Indication
Flash quickly (interval 0.1s)
Receive GSM signal
normally
Flash slowly (flash 0.1s after
every 2s)
GPRS online
Bright
Incoming/outgoing calls
Dark
No GSM signal or no SIM
card installed
2.1.4 Defense Status Indication
While the three LEDs (blue/red/green) flash cyclically, it means the device begins to
enter defense status.
Note:
1. When it runs with battery, after GPS being located over 5s, all LEDs will be
automatically turned off.
2. If there is no operation over 20s when the LEDs are lightening, all LEDs will be
automatically turned off.
3. Short press SOS button could light LEDs and press again could close it.
3. Operation
3.1 Install/Remove the SIM card
(1) Power off the device, remove the battery and external power
(2) Put the SIM card in the SIM card slot
Note: 1. Please use a GSM SIM card
2. SIM card in the device should be enabled for GPRS
3. Caller ID of the SIM card in the device should be on
Warning: Please turn off the device before removing the SIM card. It is forbidden to
install or remove the SIM card while the power is on, otherwise the SIM card may be
damaged.
3.2 Power ON/OFF
Long press the Power ON/OFF button for 2 seconds to turn on/off the device.
3.3 Charge the battery
When the red LED on the device starts to flash quickly, the battery should be charged.
Please remember to charge it before the first use.
(1) Connect the charger to power
(2) Connect the charger with the device
(3) The charging process will take about 4-6 hours.
(4) The device can work normally during charging. Red LED being light indicates
that it is charging. When charging is finished, red LED will flash slowly.
Warning: the ambient temperature shall be 0℃～40℃while charging. Please use the
charger provided by the manufacturer.
3.4 Device installation
The device has a strong magnet in rear cover which could attach to any mental
surface.
The recommended installation position is as follows;
(1) Below the front windshield with the device front up and make sure there are no
sunshade mask and other anti-GPRS reception material on it
(2) On the bottom of a car such as the side place below door. Do not put it too far
inside, otherwise it can not receive GPS signal.
Note:
1. Device should be in the place with good GPS reception.
2. Do not put the device in some place where may get rusty easily.
3. Do not put the device in some place with extremely high temperature, such as
around the radiator pipe or exhaust port, for that it may lower the magnetism
greatly.
4. To place the device under the car, please make sure GPS is located first.
4. Functions and Parameter Settings
4.1.1 APN Setting
Please send SMS command to the number of device so as to set up the APN
parameter. The device will reply “OK” automatically after setting successfully. The
SMS command is as follows:
APN,APN’s name#
E.g APN,internet#
Note: The APN of some countries have user name and password, you may need to
send SMS command as following:
APN,APN name,user name,password#
E.g APN,internet,CLIENTE,AMENA#
4.1.2 Server Parameter Setting
SERVER,0,IP,Port,0# (With IP)
SERVER,0,172.168.9.1,8800,0#
4.2 SOS Numbers Setting
4.2.1 Add SOS number by SMS
SMS command: SOS,A,number 1,number 2,number 3,number 4#(A means add
number)
E.g. SOS,A,13510682360,13511685136,13612687248,13612683621#
4 SOS numbers can be set at one time. It will reply “OK” if succeeded.
SOS,A,13527852360# means setting the first specific number
SOS,A,,,13527852360,12510682360# means setting the third and fourth SOS number
4.2.2 Delete SOS numbers by SMS
SMS command: SOS,D,1,2,3,4# (D means to delete SOS number)
For example: SOS,D,1# means to delete the first number
To delete several numbers at one time, SMS command can be: SOS,D,1,2,4# means
to delete the first, second and the fourth numbers
If you do not know the serial number, you can also delete number by SMS command
like this: SOS,D,number#
E.g. SOS,D,13527852360# means to delete this SOS number directly.
It will reply “OK” if succeeded.
4.2.3 Add SOS number via platform
You can set SOS numbers via the platform when the device connects to the platform.
Note: Only the SOS number can make the operation as remote defense, monitoring
and SMS checking position.
4.3 Arm/disarm
There are 3 methods to activate/deactivate defense status.
4.3.1 Via Power ON/OFF button
Short pressing Power button twice to activate defense status. The three LEDs will
flash slowly one by one. After 3mins, the device will enter the defense status, and the
LEDs will then flash quickly one by one.
Short press Power button twice again to deactivate defense status
4.3.2 Via Calls
Any SOS number calls the device and then ends up the call by the mobile side in 10s,
the device will enter defense status and then reply SMS “Remote setting up defense
Successful”. If the SOS number does not end up the call in 10s, it will activate
monitoring function.
Any SOS number calls the device and then ends up the call by the mobile side in 10s,
it will disarm status from the arm status and then reply SMS “Remote disarm
succeeded”. If not ends up the call in 10s, the device will enter voice-monitoring
status.
4.3.3 Via SMS command
Send SMS “111” to arm. And the device will reply SMS “Remote setting up defenses
Successful” if it is set successfully. Only SMS from SOS numbers is valid.
Send SMS “000” to disarm. And the device will reply SMS “Successful remote
disarm” if it is set successfully. Only SMS from SOS numbers is valid.
Note:
(1) If you put the device in the car, please do not set arm statue when you are driving
as it will activate the vibration sensor.
(2) Only SOS numbers can set arm or disarm.
(3) Device SIM card should activate caller-ID function.
4.4 Anti-theft alarm
In defense status, once there is a vibration, the device will send alarm SMS to the
SOS numbers in 10s.
If the device is located, it will send accurate GPS location to SOS numbers.
Otherwise, it will send LBS location first. Once it is located successfully in 2 minutes,
the device will send a GPS location. E.g:
GPS location: “vibration ,Alarm: Date time：”12-10-31 20:08:18
http://maps.\google.com/maps?q=N22.577169,E113.916790.”
LBS location: “vibration ,Alarm: Date time：12-10-31 20:08:18
http://maps.\google.com/maps?q=N22.577169,E113.916754.“
During vibration alarm time, if the device is located, but fail to connect to the
platform, the device will send longitude and latitude information. E.g.
“Vibration alarm: N23.111748, E114.409215, 11
While if the GPS is neither located nor connect to the platform, the device can not get
the position information. Then it will send SMS “vibration alarm! Attention” to SOS
numbers.
Note:
1. The device will only alarm once in 5mins.
2. If device can not send SMS normally, please check whether there is enough
balance in the SIM card.
4.5 Geo-fence
You can set a special area as geo-fence field. When the car or person gets in/out of
this area, the device will send alarm to SOS numbers when the geo-fence function is
ON.
4.5.1 Activate geo-fence function
Geo-fence function is off as default. You can activate it by SMS command.
There are two kinds of Geo-fences, circular and rectangle.
(1) Circular fence
Set a coordinate as the centre of the circular fence, and then set a distance as radius.
Go in/out fence SMS:
“FENCE,ON,0,latitude,longitude,radius#”
e.g. FENCE,ON,0,N22.57139,E113.87710,5#
It means the radius is 500 meters（radius 1=100M，2=200M····and so on）
The device will reply “OK” if set successfully. As long as the device goes in or out of
this circular area, it will send alarm to the SOS numbers.
You can also set current location coordinates as the centre of the circular fence,
“FENCE,ON,0,0,0,radius#” (This SMS command is only available when device
get located)
Go-in fence SMS:
Any number can send the following
message”FENCE,ON,0,latitude,longitude,radius,IN#” to turn on circular fence
function
e.g. FENCE,ON,0,N22.57139,E113.87710,5,IN#
It means the radius is 500 meters（radius 1=100M，2=200M····and so on）
The device will reply “OK” if set successfully. As long as the device goes in this
circular area, it will send alarm to the SOS numbers.
Go-out fence SMS:
“FENCE,ON,0,latitude,longitude,radius,OUT#”
e.g. FENCE,ON,0,N22.57139,E113.87710,5,OUT #
It means the radius is 500 meters.（radius 1=100M，2=200M····and so on）
The device will reply “OK” if set successfully. As long as the device goes out of this
circular area, it will send alarm to the SOS numbers.
(2) Rectangle fence
Specify two points in the map and use them as diagonal line, you can draw a
rectangle area, which is the rectangle fence.
Go in/out fence SMS:
Any number send the command “FENCE,ON,1,the latitude of upper left corner,
the longitude of upper left corner, the latitude of lower right corner, the
longitude of lower right corner#”.
e.g. FENCE,ON,1,N22.541183,E113.916,N22.557743,E113.892334#
The terminal will reply “OK” if set successfully. Any time the terminal enter or leave
this rectangle fence, it will send alarm message to the preset SOS numbers.
Go in fence SMS:
Any number send the command “FENCE,ON,1,the latitude of upper left corner,
the longitude of upper left corner, the latitude of lower right corner, the
longitude of lower right corner, IN#”.
E.g. FENCE,ON,1,N22.541183,E113.916,N22.557743,E113.892334,IN#
The terminal will reply “OK” if set successfully. Any time the terminal enters this
rectangle fence, it will send alarm message to the preset SOS numbers.
Go out fence SMS:
Any number send the command “FENCE,ON,1,the latitude of upper left corner,
the longitude of upper left corner, the latitude of lower right corner, the
longitude of lower right corner, OUT#”.
E.g. FENCE,ON,1,N22.541183,E113.916,N22.557743,E113.892334,OUT#
The terminal will reply “OK” if set successfully. Any time the terminal leaves this
rectangle fence, it will send alarm message to the preset SOS numbers.
(3) Example of alarm message
While the Geo-fence function is activated, each time the terminal enters or leaves the
fence area, there will be alarm message sent to the preset SOS numbers.
E.g.
GEO FenceOut[DateTime:12-06-01 14:58:03] http://maps.google.com/maps?q=N22.
577137,E113.916785
GEO FenceIn[DateTime:12-06-01 14:58:03] http://maps.google.com/maps?q=N22.5
77137,E113.916785
4.5.2 Disable Geo fence
Send SMS to disable geo-fence function: FENCE,OFF#
After get reply “OK”, geo fence function is off.
4.5.3 Check Geo fence status
Send the command SEEFENCE# to check whether geo fence function is on or off.
If geo fence is off, it will reply SMS “Switch:OFF”.
If geo fence is on, it will reply SMS
“Switch:ON;State:IN&OUT;Lat:N22.567000;Lon:E113.890000,Radius:100M;Fence
Type:Circle.”
Indice
Altri manuali Seeworld GPS
Seeworld
Seeworld S119 Manuale utente
Seeworld
Seeworld 850 Manuale utente
Seeworld
Seeworld P1 Manuale utente
Seeworld
Seeworld S117 Manuale utente
Seeworld
Seeworld S116 Manuale utente
Seeworld
Seeworld S007 Manuale utente
Seeworld
Seeworld S708 Manuale utente
Seeworld
Seeworld S6 Manuale utente
Seeworld
Seeworld S702 Manuale utente
