Segway Parking Stand Guida
WARNING!
Always shut down your Segway HT and unplug the Power Cord before performing any
maintenance or installing any part or accessory.
Follow these instructions carefully. Failure to follow these instructions could damage
your Segway HT and render it unsafe to use.
©2004 Segway LLC Page 1 of 4 18250-00001ab
Segway™Human Transporter (HT)
Parking Stand Replacement Instructions
i Series models
Questions?
If you are missing a part, or if you need to return the product, please contact Segway
Customer Operations at 1.866.4SEGWAY (1.866.473.4929) or on our website at
www.segway.com/support/contact_us.html. Check www.segway.com for updates to this
document. Thank you.
LIMITED WARRANTY
The Segway HT Tire/Wheel Assembly Kit is a “Replacement Part” covered by the SegwayTM Human
Transporter Limited Warranty (copy delivered with the kit.)
Kit Contents
> (1) Parking Stand Assembly
> (2) 4 mm Hex Drive Parking Stand Fasteners
> (6) T-20 Drive Fender Fasteners
> (1) 16 mm Wheel Nut
Note: Replace any fasteners you remove with the new
fasteners included in this kit.
Tools Required
> 16 mm deep socket
> Ratchet that will accept the 16mm deep socket
> Torque Wrench set to 50 N-m that will accept the
16 mm deep socket
> Rubber Mallet
> Torx T-20 wrench/bit
> Torx T-15 wrench/bit (if your Segway HT was
purchased prior to March 2003)
> 4 mm hex wrench/bit
> Torque Wrench set to 1.5 N-m that will accept the
Torx and Hex bits
Product Information
> Nylon retractable stand
> Foot activated lever
> Spring action
Parking Stand Replacement Instructions
©2004 Segway LLC Page 2 of 4 18250-00001ab
> Removing the Tire/Wheel Assembly
Step 1 Make sure the Parking Stand (i Series only) is
retracted. Position the Segway HT Wheels on a
non-slip surface. Brace the Wheel to be removed
so it will not rotate when you loosen the Wheel
Nut. You may find it easier to place the Handlebar
on the ground.
Step 2 Loosen the Wheel Nut with a 16 mm deep socket
by turning the wrench counterclockwise. (This may
require considerable force.) You may need to
strike the end of the wrench with a rubber mallet.
You can increase your leverage by extending the
length of the wrench handle.
Note: Your torque wrench may be designed only
for tightening. Check the manufacturer’s
specifications.
Step 3 Tip the Segway HT onto its side with the Wheel you
are removing facing up. Rest the other Wheel on a
flat, clean, smooth surface (the p Series Wheel is
dome-shaped, and is more vulnerable to scratches
and rocking unless adequately supported and
protected).
Step 4 Remove the Wheel Nut.
Step 5 Strike the outside edge of the Tire (not the Wheel!)
with a rubber mallet to unseat the Wheel Hub
Taper. (This may require multiple attempts as the
Wheel Hub Taper is seated tightly into the Gearbox
Taper.)
Step 6 Lift off the Tire/Wheel Assembly.
> Removing the Fender
Step 1 Remove the six Fender fasteners using a T-20 six-
lobed bit (Torx T-20) (T-15 Six Lobe bit if your
Segway HT was purchased prior to March 2003).
The plastic Fender is flexible. Twist the bottom
right edge of the fender and flex it away from the
Gearbox.
Step 2 Disengage the mat loop from the Fender.
Step 3 Remove the Fender.
> Removing the Parking Stand
Step 1 Remove the two 4 mm Hex Drive Parking Stand
fasteners using the “L” shaped Hex Wrench
included with your Segway HT.
Parking Stand Replacement Instructions
©2004 Segway LLC Page 3 of 4 18250-00001ab
Step 2 Disengage the Parking Stand lever from the Mat.
Step 3 Take a moment to review the position of the
Parking Stand, as a point of reference for your
installation.
Step 4 Remove the Parking Stand.
> Installing the Parking Stand
Step 1 Place the new Parking Stand Assembly against the
side of the Platform, aligning the two fastener
locations. The extrusion on the Parking Stand
bracket will seat into the larger hole beneath the
left fastener location.
Step 2 Thread in the two new 4 mm Hex fasteners.
Torque to 0.5 N-m.
> Installing the Fender
Step 1 Position the bottom left edge of the Fender into
place first. You will need to twist and flex the
bottom right edge until it seats flat against the
Gearbox. When seated properly, the six fastener
locations will align with the fastener locations in
the Chassis and Gearbox.
Step 2 Thread in and finger-tighten the six new Fender
fasteners, beginning at the bottom edges of the
Fender. Torque to 1.5 N-m using a T-20 six-lobed
bit (Torx T-20). Over tightening could strip
aluminum threads.
Step 3 (i Series and e Series models) Reach behind the
Fender and reengage the mat loop into the
Fender.
> Installing the Tire/Wheel Assembly
Step 1 Clean any debris from the outside of the Drive
Shaft and the inside of the Wheel Hub Taper using
isopropyl alcohol and a clean rag.
Step 2 Align the Tire/Wheel Assembly with the Wheel Hub
Taper over the Drive Shaft. Rotate the Wheel while
pressing down until the Wheel seats.
Step 3 Thread on the Wheel Nut. To reduce the risk of
cross threading, use only the socket (without the
wrench) to start the Wheel Nut.
Step 4 Position the Segway HT with the Wheels on a non-
slip surface. Brace the Wheel so it will not rotate
when you tighten the Wheel Nut; torque to 50 N-m.
Parking Stand Replacement Instructions
©2004 Segway LLC Page 4 of 4 18250-00001ab
Check the tire inflation pressure. The air pressure stated on the Wheel label (near the inflation valve) supersedes any
recommended pressure stated on the sidewall of the Tire.
We hope this procedure provided clear step-by-step instructions. If you feel these instructions are incorrect in any
way, we would like to hear from you. Please contact Segway Customer Support at 1-866-4SEGWAY or go to
www.segway.com if you have any questions, comments or suggestions. Thank you!
Indice
Altri manuali Segway Rack e supporto
