Seiko 7K52A Manuale dell'installatore
1
PARTS CATALOGUE / TECHNICAL GUIDE
Cal. 7K52A
CAUTION
The SEIKO SCUBA Cal. 7K52A is intended for use in diving, an inherently hazardous
form of recreation. Therefore, it is absolutely essential that you strictly observe all
instructions for the repairing and checking of the SEIKO SCUBA watch described in
this guide.
Take the greatest possible care when repairing and checking the depth measurement
function as well as the water resistant quality of this watch, because the depth meas-
urement serves as a guideline when the user is making a dive.
In addition, you must fully understand the following:
• This watch is for use in recreational scuba diving (no-decompression diving), and
is not for decompression diving, saturation diving or diving at altitudes.
• It is for use in water having a temperature range of 0°C to 40°C.
• It can measure the depth of sea water correctly, whose specific gravity is 1.025,
but not that of fresh water.
It is recommended that you explain to users the specifications of the watch, limits of
use and cautions on improper use as required. In doing so, refer to the “CAUTION”
included at the beginning of the instruction booklet of the watch.
Cal. 7K52A
2
[SPECIFICATIONS]
Item
Movement
Indication system
Depth measurement part
Time Alarm part
Hour hand
Minute hand
Small second hand
1/10 m depth hand
Diving time hand
Depth hand (Up to 55m)
Maximum depth hand
(advanced by depth hand)
Alarm hour hand
Alarm minute hand
Driving system Step motor (4 pcs.)
0 °C ~ 40 °C
Influence of temperature change of 20 °C
Within ±1 m
Loss/gain Monthly rate at normal temperature range : less than 15 seconds
Regulation system Nil
Cal. No. 7K52A
Temperature range providing warrantable
accuracy
Within ±(displayed value x 3 % + 0.5 m)
Movement
size
Outside diameter
Casing diameter
Height
ø31.0 mm
ø30.0 mm
5.9 mm
•Electronic circuit reset switch
•Train wheel setting device
•Battery life indicator
•Date calendar
•Instant setting device for date calendar
•Full automatic measurement of div-
ing data
•Recall of log data
•Depth warning function
•Single-time alarm function
Additional functions
Accuracy of the depth
measurement
Battery
Measuring gate by quartz tester
In sea water at a stable temperature
(x 1.0)
Jewels 0 jewel
Use 10-second gate.
Voltage : 3.0 V
Battery life is approximately 2 years.
SEIKO CR2016, Maxell CR2016, Sanyo CR2016, Matsushita CR2016,
Eveready CR2016
Cal. 7K52A
Please see the remarks on the following pages.
Disassembling procedures Figs. : 1 →101
Reassembling procedures Figs. : 101 →1
Lubricating: Types of oil Oil quantity
Moebius A Normal quantity
SEIKO Watch Oil S-6 Extremely small
Silicone oil 500,000 c.s.
5 Movement
PARTS CATALOGUE
Piezoelectric element
3 Case ring
21 Dial
6 Gasket for sensor unit
10 Button at the 8 o’clock side
14 Hour hand
13 Minute hand
12 Diving time hand
16 Depth hand
17 1/10 m depth hand
18 Small second hand
19 Alarm minute hand
20 Alarm hour hand
15
Maximum depth hand
22 0491 623
Dial washer
Cal. 7K52A
11 case
3
7 Button spring clip
9 Button at the 10
o’clock side
8 Button at the 2 o’clock side
23 gasket
4 Crown (with winding stem)
Lubricating of some parts is shown in “III. REMARKS ON DISASSEMBLING AND REASSEMBLING”.
1 Case back
2 Case back gasket
Insulator
0494696
(Revised: 2007/09/13
changed the part name
to Insulator from gasket)
Cal. 7K52A
4
30 1002 619
Maximum depth hand wheel
PARTS CATALOGUE
0012 354
•
Circuit block cover A screw (3 pcs.)
•
Circuit block cover B screw (1 pc.)
•
Date dial guard screw (2 pcs.)
0022 230
•
Battery clamp screw (2 pcs.)
•
Sensor clamp screw (1 pc.)
•
Anti-magnetic shield plate
screw (2 pcs.)
Lubricating of some parts is shown in “III. REMARKS ON DISASSEMBLING AND REASSEMBLING”.
Please see the remarks on the following pages.
31 Date dial
24 0012 354
Date dial guard screw
25 4283 612
Depth hand wheel clamp
28 0808 606
Date dial guard
29 1018 610
Setting lever spring for maximum
depth hand
32 0012 354
Anti-magnetic shield plate screw
34 0810 606
Date jumper
39 0271 614
Hour wheel for alarm
•
Spacer for circuit block screw (1 pc.)
27 1017 610
Setting lever for maximum
depth hand
38 0962 580
First intermediate wheel for
calendar correction
26 1002 618
Depth hand wheel
33 4259 691
Anti-magnetic shield plate
40 0271 616
Hour wheel
37 0962 590
Second intermediate wheel for
calendar correction
35 0802 605
Date driving wheel
36 0737 590
Calendar corrector setting wheel
Cal. 7K52A
47 4000 695
Sensor circuit block
Lubricating of some parts is shown in “III. REMARKS ON DISASSEMBLING AND REASSEMBLING”.
Please see the remarks on the following pages.
52 4216 691
Insulator for circuit
block
54 4457 813
Circuit block cover (B)
58 4000 696
Circuit block
PARTS CATALOGUE
43 Battery
44 4531 692
Circuit block guard
45 0022 230
Sensor clamp screw
46 4283 611
Sensor clamp
42 4225 692
Battery clamp
(with AC comment sheet)
41 0022 230
Battery clamp
screw
48 0022 230
Spacer for circuit
block screw
49 0439 612
Spacer for circuit block
50 4246 693
Buzzer lead terminal
51 4000 694
A/D circuit block
53 0012 354
Circuit block cover
(B) screw
55 0012 354
Circuit block cover (A)
screw
59 4270 690
Battery connection (-)
60 4246 691
Switch lead terminal
(A)
56 4457 812
Circuit block cover (A)
57 0396 610
Friction spring for
second counting
5
Cal. 7K52A
6
76 1002 617
1/10 m depth hand wheel
75 0817 617
Intermediate wheel for 1/10 m depth hand
Lubricating of some parts is shown in “III. REMARKS ON DISASSEMBLING AND REASSEMBLING”.
Please see the remarks on the following pages.
61 0027 974
Pin for train wheel bridge
66 1002 620
Diving time wheel
PARTS CATALOGUE
62 0125 610
Train wheel bridge
63 0950 590
Intermediate alarm wheel
64 0270 610
Center wheel for alarm
67 0241 583
Fourth wheel and pinion
68 0240 610
Second wheel
70 0231 580
Third wheel and pinion
71 0261 612
Minute wheel
72 0281 580
Setting wheel
73 0885 590
First intermediate wheel for diving time hand
65 0261 583
Minute wheel for alarm
69 0701 580
Fifth wheel and pinion
74 0885 591
Second intermediate wheel for diving time hand
77 0817 616
Intermediate wheel for depth hand
78 4283 581
Spacer for center wheel and pinion
79 0221 613
Center wheel and pinion
6
Cal. 7K52A
Lubricating of some parts is shown in “III. REMARKS ON DISASSEMBLING AND REASSEMBLING”.
Please see the remarks on the following pages.
80 4146 612
Step rotor
PARTS CATALOGUE
83 4146 612
Step rotor for 1/10 m depth hand
82 4146 612
Step rotor for alarm
81 4146 612
Step rotor for diving time hand
86 4002 693
Coil block for alarm
85 4002 690
Coil block for diving time hand
99 4450 690
Switch lever (A)
98 4450 701
Switch lever (B)
97 4450 702
Switch lever (C)
96 4239 693
Rotor stator for 1/10 m depth hand
95 4239 693
Rotor stator for alarm
94 4239 692
Rotor stator for diving time hand
93 4239 690
Rotor stator
92 0282 580
Clutch wheel
91 Winding stem (with crown)
90 0383 592
Setting lever
89 0391 591
Train wheel setting lever
88 0384 580
Yoke
87 4002 693
Coil block for 1/10 m depth hand
84 4002 690
Coil block
7
100 4242 700
Plus lead terminal
101 0100 612
Main plate
PARTS CATALOGUE
Part No.
0878 910
Position of crown
3 o’clock
Position of date frame Color of figure
White
Color of background
Black
• The explanation here is only for the particular points of Cal. 7K52A.
• For the repairing, checking and measuring procedures, refer to the “TECHNICAL GUIDE , GENERAL IN-
STRUCTIONS”.
The winding stem and crown form an inseparable unit. The winding stem alone, therefore, is unavailable
for supply but supplied as part of the crown. Check the case number and refer to “SEIKO Casing Parts
Catalogue” to choose a corresponding crown.
The type of date dial is determined based on the design of cases. Check the case number and refer to
“SEIKO Casing Parts Catalogue” to choose a corresponding date dial.
Pressure sensor
A/D - IC
Input terminal (+)
Output terminal
Output terminal
Crystal unit
Output terminal
Output terminal
Input terminal (-)
CPU-IC
<Circuit block>
TECHNICAL GUIDE
<Sensor circuit block><A/D circuit block>
Cal. 7K52A
Cal. 7K52A
Between 4 and 5 o'clock
I. STRUCTURE OF THE CIRCUIT BLOCK
31 Date dial
8
␣91 Winding stem (with crown)
Short-circuit.
1) Pull out the crown to the second click.
2) Press the button at the 2 o’clock side to reset the depth and 1/10 m depth hands to the 12 o'clock
position (0m).
3) Press the button at the 10 o’clock side to reset the diving time hand to “0” position.
4) Press the button at the 8 o’clock side to set the alarm hands to the current time.
(Here, also set the hour and minute hands to the current time.)
* The hands advance quickly if the respective buttons are kept pressed for 1 to 2 seconds.
• How to reset the depth, 1/10 m depth and diving time hands to “0” position, and how to set the alarm
hands to the current time
II. REMARKS ON INSTALLING THE BATTERY
• After the battery is replaced with a new one, or after the battery is re-installed following the repairing
procedures, be sure to short-circuit the AC terminal and the battery connection (+) (circuit block guard) to
reset the circuit as illustrated below.
After resetting the circuit, be sure to reset the depth, 1/10 m depth, maximum depth and diving time
hands to “0” position, and then set the current time.
TECHNICAL GUIDE
9
Cal. 7K52A
• Note on the demonstration function of the hands
Use the demonstration function to check that each hand moves properly.
1) Pull out the crown to the first click.
2) After the depth, maximum depth and diving time hands are all reset to “0” position, press the
button at the 10 o’clock side for more than 2 seconds.
Diving time hand Alarm hour and minute hands 1/10 m depth hand
Crown at the second click
Cal. 7K52A
10
TECHNICAL GUIDE
III. REMARKS ON DISASSEMBLING AND REASSEMBLING
The switch lead terminal is
slipped into the gap under the
auto switch terminal.
<Improper contact>
<Proper contact>
5 Movement
When installing the movement into the case, check that the switch lead terminal (A) securely makes contact
with the auto switch terminal of the case.
Note :
Be sure to observe the following to prevent any difference of indication between the depth and
maximum depth hands.
• After pressing the button at the 2 o’clock side in step "4" above, be careful not to give the watch any
vibration or impact until you finish installing the maximum depth hand.
• Push in the hands straight from above, taking care not to turn them.
*After installing the hands, recall the log data to check that :
• there is no difference of indication between the depth and the maximum depth hands.
• when the depth hand returns to indicate the average depth, the maximum depth hand stays where it
was advanced by the depth hand.
Switch lead terminal (A) Auto switch terminal
15 Maximum depth hand
17 1/10 m depth hand
16 Depth hand
10
1/10 m depth hand
Depth hand
Maximum depth
hand
• Remarks on installing
• When installing the hands for diving measurement, check
that they accurately point to the diving measurement
scales on the dial.
• The depth hand moves correspondingly with the 1/10 m
depth hand, and the maximum depth hand is advanced by
the depth hand. To install them, therefore, be sure to
follow the procedure below.
1) Reset the circuit.
2) Pull out the crown to the second click and wait for more
than 40 seconds until all the wheels on the train wheel
bridge stop moving.
3) Reset the 1/10 m depth and depth hands to “0” posi-
tion as shown in the illustration at upper right.
4) After pressing the button at the 2 o’clock side more
than 15 times, put the maximum depth hand exactly
onto the depth hand as shown in the illustration at right.
Indice
Altri manuali Seiko Orologio
Seiko
Seiko 7S26 Manuale utente
Seiko
Seiko SPC167P1 Manuale utente
Seiko
Seiko Astron 3X22 Manuale utente
Seiko
Seiko KINETIC 7D46 Manuale utente
Seiko
Seiko Limited Edition Age of Discovery Manuale utente
Seiko
Seiko Y911A Guida rapida
Seiko
Seiko Astron 7X52 Manuale di istruzioni
Seiko
Seiko 8J55 Manuale utente
Seiko
Seiko KINETIC 7D46 Manuale utente
Seiko
Seiko 2A27 Manuale utente
Seiko
Seiko ASTRON Guida all'installazione
Seiko
Seiko 5Y75 Manuale utente
Seiko
Seiko Cal. V175 Manuale utente
Seiko
Seiko 7C17B Guida rapida
Seiko
Seiko SSA447 Manuale utente
Seiko
Seiko 5T82A Guida rapida
Seiko
Seiko A156A Guida rapida
Seiko
Seiko 4F32A Guida rapida
Seiko
Seiko V115A Guida rapida
Seiko
Seiko T-4 Manuale utente
