Seiko G510 Guida rapida
= Precautions
For G510 caliber watches, as they incorporate a microcapsule-type
electrophoresis display module and employ a special case structure, all repair,
adjustment, and replacement must be carried out in Japan, with the exception
of replacement of “Urethane Safety Catcher” or batteries.
Battery replacement can be done only at Seiko Service Centres where the
Water-Resistance Tester S-451A is equipped.
As soon as you receive a request from a customer, immediately contact the CS
Department.
11) Loosen and remove the four “battery cover screws” (#7500920).
* Use sufficient force as adhesive is used for preventing the screws from
loosening.
Pay attention not to damage or scratch the case and battery cover.
The other 6 screws should not be touched.
Use a short screwdriver because the case shape is unusual.
Avoid diagonally inserting a long screwdriver because this will cause
damage to the screw head.
1/4
PARTS CATALOGUE /TECHNICAL GUIDE
SEIKO EPD WATCH
Cal. G510
(for Battery Replacement)
2 Remove the “battery cover.”
Remove the “battery clamp” (#4225544) using tweezers.3
4Replace the battery (CR2025)
When setting the battery, insert it diagonally from the side so as not to
bend the terminal spring.
Set the “battery clamp” correctly.
5
6Touch the two terminals beside the battery to create a short circuit for
resetting system.
* Refer to the instructions on the rear side of the battery cover.
2/4
TECHNICAL GUIDE Cal. G510
* Confirm that the display shows <12:00>.
Apply a small amount of adhesive “LOCTITE 241” to the four screw
holes on the battery cover.
*First, remove any remaining adhesive before applying the new adhesive.
Set “gasket for the battery cover” (0G286BCA2).
8
* Be sure to use a new one.
7
* Apply grease as necessary.
Close the “battery cover.”
9
* Pay attention not to displace the “gasket.”
* You may put the “battery cover” below, and place the watch body onto
the cover.
*Dry the adhesive with the battery cover down under a temperature
of not more than 50°C.
3/4
TECHNICAL GUIDE Cal. G510
Check that the display shows the time by pressing “button A” and the
calendar by pressing “button B.”
11
Button A Button B
Ensure the non-water resistant level by use of the water-resistance
tester S-451A.
* Set the detector to the glass part in a similar manner as a normal
watch.
* In the case where water resistance cannot be determined, remove the
battery cover to reset the gasket and try again.
10
4/4
TECHNICAL GUIDE Cal. G510
Parts for G510
CASE BACK SCREW 81506329
BATTERY HATCH GASKET 0G286BCA2
URETHANE SAFETY CATCHER DFW8EB
ATTERB Y CLAMP 4225544
Indice
Altri manuali Seiko Orologio
Seiko
Seiko Time Keeper ViB+ Manuale utente
Seiko
Seiko S620 Manuale utente
Seiko
Seiko SSC642P Manuale utente
Seiko
Seiko Spring Drive IZUL 5R85 Manuale utente
Seiko
Seiko 6R15A Manuale utente
Seiko
Seiko S802 Manuale utente
Seiko
Seiko Presage SPB305J Manuale utente
Seiko
Seiko UC-2000 Manuale utente
Seiko
Seiko S101A Guida rapida
Seiko
Seiko SSC141P1 Manuale utente
Seiko
Seiko Prospex 7K32 Manuale utente
Seiko
Seiko W850A Guida rapida
Seiko
Seiko Presage SSA457J Manuale utente
Seiko
Seiko V110 Manuale utente
Seiko
Seiko G757(GZC) Manuale utente
Seiko
Seiko SRX011P1 Manuale utente
Seiko
Seiko Kinetic 5M65 Manuale utente
Seiko
Seiko SPC161P1 Manuale utente
Seiko
Seiko 5R64 Manuale utente
Seiko
Seiko Presage SSA439J Manuale utente
