SELECTRONIX SUPERSTEP SERIES 4000 Guida rapida

ELECTRONIX,

NC.

WOODINVILLE, WA

SUPERSTEP SERIES 4000

SLC4075 Touch Screen GATEWAY

Startup Configuration Modification Guide

1. Models: SLC4075-4 4” Screen

2. Models: SLC4075-7 7” Screen

TSGW_ Startup Configuration Modification Guide

Rev 10/12/17

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

TABLE OF CONTENTS

INTRODUCTION .......................................................................................................................................................3

PREREQUISITES .......................................................................................................................................................3

DETAILED INSTRUCTIONS ...................................................................................................................................3

PID1...............................................................................................................................................................................4

SPM1 .............................................................................................................................................................................4

PID2, GPA1 AND GPA2.................................................................................................................................................4

SPM2 .............................................................................................................................................................................5

AUX/BMS AUTOMATICALLY SWITCH TO AUX ON GPDI FAULT .....................................................................................5

GPDI ..............................................................................................................................................................................5

XDI ................................................................................................................................................................................6

PGW RELAYS.................................................................................................................................................................7

XRLYS............................................................................................................................................................................8

VOLTAGE DRIVER ..........................................................................................................................................................9

Introduction

This document provides instructions for modifying the default startup options and descriptive labels, for Touchscreen Gateway

(TSGW) firmware version 2.0 and on The options and values set in this text file unconditionally sets values on power up.

As such, do not enter values or uncomment options whose value that are desired to be changed and retained during operation.

Once the desired values and options have been established, they may be saved permanently in this database and provides an electronic

and human readable backup of the settings.

Prerequisites

1. Crimson software version 697.00 and on (available free from www.redlion.net Support; Software & Firmware; Red Lion

Software; Crimson; Crimson 3.0

2. Crimson database obtained from the boiler manufacturer or Selectronix tech support.

3. PC to upload modified database to the TSGW.

Detailed Instructions

1. Open Crimson 3 software and load the original Crimson database.

2. In the Navigation Pane’s lower window, click on ‘Display Pages’

3. In the Navigation Pane’s upper window, click on ‘Pages’

4. In the middle window, ‘Global Actions’;’On Startup’; ‘Complex’; ‘Complex Code’, click on Edit…

5. A text editor opens with a title ‘Edit Complex Code’.

a. The first 3 configurable items set the Company Info, Basic Configuration, and Screen size, which would not

normally be changed from the delivered database.

b. Note the selection for Item 2, Basic Configuration

i. TSGW.g_iCfgSpecificOptSelect = TSGW.CFG.PGS_ONSTARTUP_.......

ii. This is the selector for the specific block of code applicable to your database.

iii. Scroll through the text to find this block of code.

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

PID1

This block sets the following:

1. // PGW.PID1.g_fUnmodSetptDeg = PGW.PID1.UNMOD_SETPT_DEFVAL;

a. Sets the default set point in degrees. It is commented out for field modification

2. PGW.PID1.g_fSetModeSel = PGW.PID.PID_MODE_EN_NON_INV_BMS; // Heat mode

a. Sets the PID mode and would not normally be changed in the field

3. PGW.PID1.g_fSetEngrUnits = PGW.PID.PIDSPM_UNITS_DEGF;

a. Sets the engineering units, either degrees F or degrees C

i. Change to PGW.PID.PIDSPM_UNITS_DEGC for Celcius

4. // PGW.PID1.g_iSetPreset = PGW.PID.PID_PRESET_SEL_SLOW;

a. Sets the default PID preset which would not normally be changed

5. // PGW.PID1.g_fSet_P = PGW.PID.PID_PRESET_P_SLOW_DEFVAL;

a. Set the PID1 Proportional value. Uncomment this line and set the desired unchangeable number

6. // PGW.PID1.g_fSet_I = PGW.PID.PID_PRESET_I_SLOW_DEFVAL;

a. Set the PID1 Integral value. Uncomment this line and set the desired unchangeable number

7. // PGW.PID1.g_fSet_D = PGW.PID.PID_PRESET_D_SLOW_DEFVAL;

a. Set the PID1 Derivative value. Uncomment this line and set the desired unchangeable number

SPM1

Sets the Set Point Modifier 1 (Outdoor Air Reset) parameters

Sets the SPM source selection. Uncomment the line that sets the desired mode

1. // PGW.SPM1.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_DIS;

2. // PGW.SPM1.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_RTD2_DEGF;

3. // PGW.SPM1.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_RTD2_DEGC;

4. // PGW.SPM1.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_GPA2_PCTSPAN;

5. // PGW.SPM1.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_GPA2_EU;

PID2, GPA1 and GPA2

// PID2 and GPA1

1. PGW.PID2.g_fSetModeSel = PGW.PID.PID_MODE_DIS; // Disabled

Sets the PID2 mode select

a. Set the desired mode from tags located in PGW.PID.xxx

2. PGW.GPA1.g_fEUMappedToZeroPct = PGW.GPA.PSI_0;

Sets the engineering value mapped to 0 span percent.

3. PGW.GPA1.g_fEUMappedTo100Pct = PGW.GPA.PSI_150;

Sets the engineering value mapped to 100 span percent.

a. Set this to the desired engineering unit at 100 span percent.

Example: to change the default range from 0-150 PSI to 0-15 PSI, change this to PGW.GPA.PSI_15, or simply 15.

4. PGW.PID2.g_fSetEngrUnits = PGW.PID.PIDSPM_UNITS_PSI;

// GPA2

1. PGW.GPA2.g_fEUMappedToZeroPct = PGW.GPA.PCTSPAN_0;

Sets the engineering value mapped to 0 span percent.

2. PGW.GPA2.g_fEUMappedTo100Pct = PGW.GPA.PCTSPAN_100;

Sets the engineering value mapped to 100 span percent.

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

SPM2

Sets the Set Point Modifier 2 parameters

Sets the SPM source selection. Uncomment the line that sets the desired mode

1. // PGW.SPM2.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_DIS;

2. // PGW.SPM2.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_RTD2_DEGF;

3. // PGW.SPM2.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_RTD2_DEGC;

4. // PGW.SPM2.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_GPA2_PCTSPAN;

5. // PGW.SPM2.g_fSetSPMSrcSel = PGW.SPM.SPMSRC_GPA2_EU;

Aux/BMS automatically switch to Aux on GPDI ault

The Aux/BMS may be programmatically enabled to switch to the Aux position on a fault.

Find line and set to true to enable the switch to Aux mode on a GPDI fault.

// *******************AUX/BMS position on Alarm**********************

PGW.GPDI.g_bAuxOnAlarm = false; // Switch to Aux on Alarm

GPDI

1. // *******************AUX/BMS position on Alarm**********************

Sets whether the Aux/BMS switch reverts to Aux on a defined GPDI alarm

PGW.GPDI.g_bAuxOnAlarm = false; // Switch to Aux on Alarm

2. // GPDI Invert sense

Sets whether the specified bit is inverted or not. A ‘0’ is non-inverted

a. PGW.GPDI.g_iSetGPDISdEnAndInvMask.0 = 0;

b. PGW.GPDI.g_iSetGPDISdEnAndInvMask.1 = 0;

c. PGW.GPDI.g_iSetGPDISdEnAndInvMask.2 = 0;

d. PGW.GPDI.g_iSetGPDISdEnAndInvMask.3 = 0;

3. // Alarm Titles and Enables for Level-triggered with Siren [.7-.4]

a. TSGW.g_bCfgGPDIAlmEn[0] =1;

This defines whether this GPDI bit is an alarm to be displayed on the TSGW

b. PGW.GPDI.g_iSetGPDISdEnAndInvMask.4 = 1;

This defines whether or not this GPDI bit causes the SLC4000 to ShutDn the output of ALL the SLC4000 units, applicable

for a single boiler operation. This bit is normally set to 0 for multiple boiler systems, which allows the other units to

continue to output .

4. PGW.GPDI.g_strGPDI_AlmEvtName[0] = "Low Water";

Sets the TSGW label for this alarm

5. PGW.GPDI.g_iGPDI1_MultiLbl = 2; // Low Water

Sets the label displayed on the GPDI page

6. PGW.GPDI.g_iGPDI2_MultiLbl = 3; // High Limit

7. PGW.GPDI.g_iGPDI3_MultiLbl = 4; // Status

8. PGW.GPDI.g_iGPDI4_MultiLbl = 1; // GPDI4 Unused

The labels for the GPDI1 through GPDI4 are controlled by a multi-state tag. The various names within the tag contain several of the

commonly used labels. Other names may be added to customize the database for future use.

1. Using an existing label

a. State 1 GPDIn Unused (n is GDPI number)

b. State 2 Low Water

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

c. State 3 High Limit

d. State 4 Status

e. State 5 Boiler #n Lockout (n is GDPI number)

2. If the GPDI is assigned to operate the Relays, those labels need to be changed, as well.

3. Adding a new label

a. In the Navigation Pane, select Data Tags

b. Select PGW; GPDI; g_iGPDIn_MultiLbl, where n is the GPDI number

c. In the format tab; Format States

i. Add a new state with a new label

XDI

XDI is the eXpansionl Digital Input, SLC4080

1. // Shutdown mask is for a input that causes S4K to turn off all rlys and flash red status

XDI.g_iSetSdMask = 0b00000000; // Disable all Shutdn enable

2. XDI.g_iSetInvMask = 0b00000000; // All normal sense

Sets the invert mask for the specific bits

3. XDI.g_iInp1Bit0_MultiLbl = 1; // XDI Unused

Set the label for this bit

Create a new label by defining in XDI.g_iInp1Bit0_MultiLbl

4. XDI.g_iInp1Bit1_MultiLbl to XDI.g_iInp1Bit7_MultiLbl

Set the label for the specific bit

Create a new label by defining in XDI.g_iInp1Bitn_MultiLbl, where n is the specific bit number

5. // TSGW Alarm Enable for Level-triggered with Siren (default) and TSGW Alarm Titles

6. TSGW.g_bCfgXDIAlmEn[0] = 0;

Sets whether this XDI bit is to display an TSGW alarm

7. TSGW.g_strXDIAlmEvtName[0] = "Unused 1";

Sets the text to display on the TSGW alarm page for this XDI bit

8. TSGW.g_bCfgXDIAlmEn[1] = 0;

through TSGW.g_bCfgXDIAlmEn[7] is the same as for TSGW.g_strXDIAlmEvtName [0]

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

PGW Relays

1. // Src Sel

Sets the source for PGW relays 1-3

PGW.Rly.g_fSetPGWRlysSrcSel[0] = PGW.Rly.RLYSRCSEL_GPDI;

PGW.Rly.g_fSetPGWRlysSrcSel[1] = PGW.Rly.RLYSRCSEL_GPDI;

PGW.Rly.g_fSetPGWRlysSrcSel[2] = PGW.Rly.RLYSRCSEL_GPDI;

Other Rly sources are:

a. PGW.Rly.RLYSRCSEL_DISABLED

b. PGW.Rly.RLYSRCSEL_BMS

Relay is controlled by BMS

c. PGW.Rly.RLYSRCSEL_CLL

Relay is controlled by Classic Lead Lag

d. PGW.Rly.RLYSRCSEL_S4K_FLT

Relay is energized when the S4K fault is non-zero

e. PGW.Rly.RLYSRCSEL_PGW_FLT

Relay is energized when the PGW fault is non-zero

f. PGW.Rly.RLYSRCSEL_TSGW_FLT

Relay is energized when the TSGW fault is non-zero

g. PGW.Rly.RLYSRCSEL_GPDI_AND_GPDI4

Relay is energized when both the same numbered GPDI AND GPDI4 is logically set

h. PGW.Rly.RLYSRCSEL_GPDI_OR_GPDI4

Relay is energized when both the same numbered GPDI OR GPDI4 is logically set

2. // Src Sel Labels

Sets the label to be displayed on the SLC4060 Relays page. See the applicable PGW.Rly.g_iRlySrcSel_MultiLbl[0] to

PGW.Rly.g_iRlySrcSel_MultiLbl[2] to select a different label, or define a new label.

a. PGW.Rly.g_iRlySrcSel_MultiLbl[0] = 1; // GPDIx

b. PGW.Rly.g_iRlySrcSel_MultiLbl[1] = 1; // GPDIx

c. PGW.Rly.g_iRlySrcSel_MultiLbl[2] = 1; // GPDIx

3. // Rly Desc Labels

Sets the label to be displayed on the SLC4060 Relays page. See the applicable PGW.Rly.g_iRly1_MultiLbl to

PGW.Rly.g_iRly3_MultiLbl to select a different label, or define a new label.

PGW.Rly.g_iRly1_MultiLbl = 2; // Low Water

PGW.Rly.g_iRly2_MultiLbl = 3; // High Limit

PGW.Rly.g_iRly3_MultiLbl = 4; // Status

The labels for the GPDI1 through GPDI4 are controlled by a multi-state tag. The various names within the tag contains

several of the commonly used labels. Other names may be added to customize the database for future use.

1. Using an existing label

a. State 1 Rlyn Unused (n is Rly number)

b. State 2 Low Water

c. State 3 High Limit

d. State 4 Status

e. State 5 Boiler #n Lockout (n is Rly number)

2. Adding a new label

a. In the Navigation Pane, select Data Tags

b. Select PGW; Rly; g_iRlyn_MultiLbl, where n is the Rly number

c. In the format tab; Format States

i. Add a new state with a new label

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

XRlys

1. // Src Sel selects the pre-defined definition for all rlys

XRly.g_iSrcSel=XRly.SRCSEL_XDI_1;

Sets the src to operate the like-numbered relay

Other source choices are:

a. SRCSEL_DIS_0

i. All XRlys are disabled

b. SRCSEL_XDIFLT_2

i. Relays 1-4 by the like-numbered XDI

ii. Relays 5 is energized when the PGW fault is non-zero

iii. Relays 6 is energized when the TSGW fault is non-zero

iv. Relays 7 is energized when the S4K fault is non-zero

v. Relays 8 is reserved

c. SRCSEL_XDIBMS_3

i. Relays 1-4 by the like-numbered XDI

ii. Relays 5-8 are controlled by the BMS

d. SRCSEL_BMS_4

i. Relays are controlled by the BMS

e. SRCSEL_CLLXDI_5

i. Relays 1-4 are controlled by Classic Lead Lag

ii. Relays 5-8 are controlled by the like-numbered XDI

f. SRCSEL_CLLBMS_6

i. Relays 1-4 are controlled by Classic Lead Lag

ii. Relays 5-8 are controlled by the BMS

2. // XRlys Desc Labels

Sets the text label displayed on the XRlys page

XRly.g_iRly1_MultiLbl = 1;

XRly.g_iRly2_MultiLbl = 1;

XRly.g_iRly3_MultiLbl = 1;

XRly.g_iRly4_MultiLbl = 1;

XRly.g_iRly5_MultiLbl = 1;

XRly.g_iRly6_MultiLbl = 1;

XRly.g_iRly7_MultiLbl = 1;

XRly.g_iRly8_MultiLbl = 1;

www.selectronix.us

Selectronix, Inc.

(425) 788-2979

SLC4075 TouchScreen Gateway Startup Configuration Modification Guide

___________________________________________________________________________________________________

Voltage Driver

1. // ------------------------------VltDrvr---------------------------------

Sets the source for the voltage driver output

PGW.VltDrvr.g_fSetVltDrvrSel = PGW.VltDrvr.VLTDRVR_PID1_0_10;

This sets the output to PID1 percent using 0 to 10 volt.

// Note that field choice of VltDrvrSel auto selects the applicable PGW.VltDrvr.g_iVltDrvr_MultiLbl

a. Other choices for the voltage driver are:

i. PGW.VltDrvr.VLTDRVR_DISABLED

Disabled the output

ii. PGW.VltDrvr.VLTDRVR_BMS

Output controlled by BMS

iii. PGW.VltDrvr.VLTDRVR_GPA1

Output controlled by GPA1 span percent

iv. PGW.VltDrvr.VLTDRVR_GPA2

Output controlled by GPA2 span percent

v. PGW.VltDrvr.VLTDRVR_RTD1

Output controlled by RTD1 span percent

vi. PGW.VltDrvr.VLTDRVR_RTD2

Output controlled by RTD2 span percent

vii. PGW.VltDrvr.VLTDRVR_PID1_2_10;

This sets the output to PID1 percent using 2 to 10 volt.

viii. PGW.VltDrvr.VLTDRVR_PID2_0_10;

This sets the output to PID2 percent using 0 to 10 volt.

ix. PGW.VltDrvr.VLTDRVR_PID2_2_10;

This sets the output to PID2 percent using 2 to 10 volt.

Altri manuali per SUPERSTEP SERIES 4000

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Pannello touch popolari di altre marche

FlowLine

FlowLine Data loop Manuale utente

ALPEX

ALPEX AEx-8 P Series Manuale utente

Ltech

Ltech E5S Manuale utente

Harman

Harman AMX MODERO S MSD-701-L2 Manuale utente

Acnodes

Acnodes PC 1150 Manuale utente

AIS

AIS IP10IA99 series Manuale utente

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuale utente

YASKAWA

YASKAWA TP 610C Manuale utente

B&R

B&R Power Panel C Series Manuale utente

Beijer Electronics

Beijer Electronics X2 control Manuale utente

AXIOMTEK

AXIOMTEK GOT321W-521 Manuale utente

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuale utente

Qomo

Qomo QIT1386 Manuale utente

DFI

DFI KS104-CD Manuale utente

AMX

AMX AXP-PPC Guida

Sartorius

Sartorius X3 PR 5410 Manuale utente

AMX

AMX Modero X Series Manuale utente

Advantech

Advantech TPC-30 Series Manuale utente