Self-Sat SELFSAT-H30D Series Manuale utente
ENGLISH
Contents
What is SELFSAT-H30D Travel Kit?
...........................................................................What is SELFSAT-H30D Travel Kit? 2
｜
Safety Instructions
...........................................................................................Safety Instructions 2
｜
Box Content
.................................................................................................Box Content 3
｜
How to Install?
...............................................................................................
....................................................................................
..................................................................................
................................................................................
.....................................................
....................................................................
...............................................................
................................................................
....................................................
.....................................................................
............................................................................
....................................
How to Install?
Step 1 : Where to Install?
Step 2 : Check Information
Step 3 : Assembly Instruction
Step 4 : Connecting the Antenna and the Set top box
Step 5 : Fine Tuning and Fix the Bracket
｜
｜
｜
｜
｜
｜
A) Joint Angle Bracket and Antenna Body
B) Assembling the Multi-Functional Base
C) Installing and xing the base of the camping set
D) Adjusting azimuth and elevation
A) How to prepare the cable?
B) How to connect the cable to the antenna and the set top box?
4
4
5
5
13
14
5
5
7
12
13
13
Troubleshooting Check List for Initial Installation
..........................................................Troubleshooting Check List for Initial Installation 15
｜
Loss of Signal / Rain Fade
....................................................................................Loss of Signal / Rain Fade 15
｜
2
Warning
Antennas improperly installed or installed to an inadequate structure are very susceptible to wind
damage. This damage can be very serious or even life threatening. The owner and installer assumes full
responsibility that the installation is structurally sound to support all loads (weight, wind & ice) and
properly sealed against leaks. The manufacturer will not accept liability for any damage caused by a
satellite system due to the many unknown variable applications.
Before using this product please read this manual carefully and follow exactly all installation, mounting &
orientation instructions.
All the instructions should be followed in order to avoid any technical problems.
Any electric or magnetic eld close to the SELFSAT-H30D Travel Kit may cause a bad reception or even cut o the
signal completely.
Do not drill the plastic cover of the antenna, which seals the antenna from moisture.
Handle the antenna with care as any impact will cause damage to the electronics.
Do not open the cover, any attempt to repair by a non-qualied person can be dangerous and void the warranty.
Any obstacle (buildings, trees, etc....) will block the reception of the signal from the satellite to the antenna.
Do not paint or add any substance on the antenna cover, this will block the reception of the signal from the
satellite.
The cable between the antenna and the Satellite receiver should not exceed 30m as it will decrease the quality of
the signal.
The use non- isolated jacks will result in a loss of the signal level.
Tighten all the screws of the antenna once you have nished the adjustments.
This product contains one universal LNB, it is forbidden to add, change or modify the LNB.
For more precise details on the above points or for any information, please ask your retailer or customer service.
•
•
•
•
•
•
•
•
•
•
•
•
•
Safety Instructions
What is SELFSAT-H30D Travel Kit ?
3
ENGLISH
Contents
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
1
1
1
1
1
1
1
1
1
1
2
5
1
2
1
A1
B1
B2
B3
B4
B5
B6
B7
C1
S1
S2
S3
S4
S5
S6
S7
Antenna Body
Angle Bracket
Multi-Functional Base
Suction cup
Fix Plate
10m Coaxial Cable with F-Connector
Manual
Carrying case
Compass
L type bolt
U type bolt
M6x65 Hex
M6 Knob Nuts
M8 Knob Nuts
M6x18
M6x60
Symbol Part name Image Quantity
(Optional)
4
Note
please take reference to the table of the Azimuth angles specied in the back pages of this manual.
Note
< Compass > < Azimuth Angle >
To ensure an accurate compass reading, stay away from large metal objects, specically electrical cables
and then make multiple readings.
Bad Quality Singnal Reception
BAD!BAD!
Good Quality Singnal Reception
GOOD!GOOD!
Azimuth
Angle
S 180o
N 0o
Satellite position
How to Install?
By following the instructions step by step, you can proceed easily to install
SELFSAT-H30D Travel Kit by yourself or with the help of a professional antenna installer.
Step 1: Where to Install?
In order to receive a signal from the Satellite, SELFSAT-H30D Travel Kit is to be installed in an open loop space
(outside the house or the apartment), in the direction of the satellite towards the equator, for which, you will
need a compass to exactly orient SELFSAT-H30D Travel Kit toward the satellite.
Make sure that there are no obstacles in front of SELFSAT-H30D Travel Kit which can decrease the signal reception
quality, such as buildings or trees (you may keep in mind that trees will grow and may block the signal).
In order to be able to x and install your antenna easily, you might choose an easily accessible place without any
potential danger for installation.
Think about the way you might pass your cable in a discreet way from the SELFSAT-H30D Travel Kit to your Set top
Box. The antenna should not be too distant from your satellite receiver; a cable longer than 30 meters may decrease
the quality of the signal.
Before installing your antenna, you check that SELFSAT-H30D Travel Kit box contains all the items listed above
in the ‘Box Content’. In the event of any missing parts, please contact your distributor.
5
ENGLISH
Step 3 : Assembly Instruction
A) Joint Angle Bracket and Antenna Body
Joint Angle Bracket and Antenna Body by screw
1)
S6
S4
S6
S7
A1
B1
B) Assembling the Multi-Functional Base
Open the Multi-Functional Base
- Open the two wings of the Multi-Functional
1)
B2 B2
Step 2: Check Information
In order to install antenna, you need to nd skew, elevation and azimuth angle by referring the table on the
back of the manual. If you can’t nd your location, please refer to the information of the nearest place from
your location. This manual will show you the installation example to receive ASTRA1 satellite in Brest region
of France. The angle information for Brest region is Skew : -19.7, El : 30, Az : 149.6
6
S4
S3
Fold the Multi-Functional Base
-
Use the two M6*65mm Hex. Head Screws and two M6 Knob Nuts to fasten the Multi-Functional Base
2)
B2
-
Pull out the Base Support, then put it on the plane
B2
B2
7
ENGLISH
C) Installing and xing the base of the camping set
Type 1
Take the folded Multi-Functional Base on the table
Putt he long side of L-Type Bolt into the Fix Plate and the short side into the Multi-Functional
Base
1)
2)
B2
B4
Use the M8 Knob Nut to fasten the Fix Plate and the Multi-Functional Base
Insert the Dish Set onto the Multi-Functional Base and M6*25mm Knob Screw to fasten the
Camping-Set on the table
3)
4)
S5
S1
S1
M6 x 25mm
Knob nut
B2
B4
8
Type 2
Put the folded Multi-Function Base along a mast and insert the U-Type Bolt into the
Multi-Functional Base. Then use two M6 Knob Nuts to fasten the Multi-Functional Base on the
mast.
Insert the Dish Set onto the Multi-Functional Base and use M6*25mm Knob Screw to fasten the
Camping-Set.
1)
2)
B2
Type 3
Take the open Multi-Functional Base and slightly loosen the M6*25mm Knob Screw
Insert the Dish-Set onto the opened Multi-Functional Base. Then tighten the M6*25mm Knob
Screw
1)
2)
S3
S4
S2
B2
B2
B1
A1
M6 x 25mm
Knob Screw
M6 x 25mm
Knob Screw
9
ENGLISH
S4
S4
S4
Type 4
Upright the handle of the suction cup, then push it on the plane
Press the handle of the suction cup backwards to x the suction cup base
1)
2)
Lightly loosen the M6 Knob Nut, then slide the folded Multi-Functional Base into the suction cup
set to the end (see red arrow below)
3)
B3
B3
B3
B3
B2
B2
B2
Push
Make a sound of „Click“
B3
10
Insert the Dish Set onto the Multi-Functional Base and use M6*25mm Knob Screw to fasten the
Camping-Set
4)
Type 5
Upright the handle of the suction cup, then push it on the plane
Press the handle of the suction cup backwards to x the suction cup base
1)
2)
B3
Push
Make a sound of
„Click“
B3
M6 x 25mm
Knob Screw
Altri manuali per SELFSAT-H30D Series
1
Indice
