Semtronics 62532 Manuale utente

TB-6108 Page 1 of 9 Revision 07/05

Employee Owned

62532 (EN649)

Ethernet Adapter

INSTALLATION AND OPERATING

INSTRUCTIONS

For sales and Service in

North America contact:

ESD Systems.com

www.esdsystems.com

[email protected]

Phone: 508-485-7390

Fax: 508-480-0257

Corporate Office:

3651 Walnut Avenue,

Chino, CA 91710

Phone: (909) 627-8178

Fax (909) 627-7449

For sales and service in Europe and

Asia contact:

OK International - European Headquarters

Eagle Close, Chandlers Ford,

Hampshire, SO53 4NF U.K. England

http://www.okintl.com/locations.htm

Tel: +44 (0)23 8048 9100

Fax: +44 (0)23 8048 9109

TB-6108 Page 2 of 9 Revision 07/05

Employee Owned

Introduction:

The Semtronics 62532 Ethernet adapter provides an easy and effective means of retrieving

data from Semtronic’s 62580 and 62581 Smartlog X3 from anywhere within the LAN or from

any location in the world. By using the Semtronics 62532, the Smartlog X3 can be mounted

anywhere in the facility without the use of a dictated PC where a network port is accessible.

Specifications:

•Dimension: 6.4cm x 9.0cm x 2.3cm, 2.5”W x 3.5”D x 0.9”H

•Weight 0.8 lbs

•Universal powers supply with interchangeable outlet adapter. Input 110-230 VAC

50/60Hz. Output 12VDC/0.8A. 2.5mm female power jack, center positive. Any alternate

transformer must comply with the Safety Extra Lox Voltage (SELV) insulation

requirements.

Important: This appliance has a metal casing and is considered to be class I and tested

as class II. The power supply connection plug is accessible to the user and this no safety

insulation inside the 62532. Therefore the insulation of the power supply is critical.

•Rated power consumption: 3A maximum

PC Requirements:

Intel® Pentium® II or above processor. Operating platform, Windows®2000 (with service

pack 2)

Additional Software:

Lantronix redirector, compact redirector (red), downloaded from www.lantronix.com

Environmental Conditions:

Pollution degree 2 per IEC 644

Temperature:

Operating Range: 5 to 50 °C, 41 to 122 °F

Storage Range: -40 to 66 °C, -40 to151 °F

Maximum Temperature Change Per Hour: 20°C, 36°F

Note: Maximum temperature changes may affect operation, Therefore, do not operate the

unit near heating or cooling devices, large windows, or doors that opens to the outdoors.

Altitude:

TB-6108 Page 3 of 9 Revision 07/05

Employee Owned

Operating: 2.4km, 8000ft

Storage: 9.1km, 30000ft

Note: If operating unit above 2.4km or 8000ft, decrease the operating temperature rating by 1

degree for every 1000ft.

Figure 1. Bottom View

Figure 2. Top View

TB-6108 Page 4 of 9 Revision 07/05

Employee Owned

Current RS-232 Configuration (Use only when DB25 connector is labeled RS-232)

Figure 3. Connection Setup

TB-6108 Page 5 of 9 Revision 07/05

Employee Owned

Previous RS-485 configuration (Old configuration, no label on DB25)

Figure 4. Connection Setup

A. Hardware Setup

1. Insert DB25 serial adapter to female DCE DB25 serial port of the 62532 Ethernet

adapter.

2. Connect cable from RJ11 jack of serial adapter to RS-485 port (left RJ11 port) of

Smartlog X3 (Refer to Figure 4). Connect to RS-232 port on RS-232 connector (figure 3)

only if labeled RS-232.

TB-6108 Page 6 of 9 Revision 07/05

Employee Owned

3. Connect power adapter and network wires.

4. Before mounting 62532, MAC address located on back side needs to be noted for

proper programming of Ethernet adapter.

B. Assigning IP Address

1. Connect the 62532 to an Ethernet port within the LAN connection.

2. Power the unit on, the green LINK LED should be on, the red DIAGNOSTIC

LED should be flashing then off when the green STATUS LED comes on. The

orange NET Tx\Rx should be flashing.

3. On the same LAN connection, you’re going to need a PC to set and program

the 62532. Go to your Start icon in Taskbar of Windows®. Go to Run and type

in CMD and hit enter. This should take you to the Command Prompt. Type in

CD\ and hit enter to get to the root directory. (Figure 5).

Figure 5

4. Type: arp –s <IP address> <Physical address> and hit enter. The IP address

needs to be assigned by IT. The MAC address is located on the back of the

62532 ethernet adapter. (Figure 6)

Figure 6

TB-6108 Page 7 of 9 Revision 07/05

Employee Owned

5. Let’s use 192.168.10.13 as an example IP address. Type in telnet

192.168.10.13 1 and hit enter, make sure you type in 1 for the port. It will

display “Could not open connection to host, or port 1: connection fail”.

6. Then Type in telnet 192.168.10.13 9999 and hit enter, you should now have

connection to the host, hit enter again to go into setup mode. (Figure 7)

Figure 7.

7. Enter 0 and Hit Enter for Server Configuration.

a. Assign IP Address: It will ask you to assign an IP address for the unit.

Have this IP address written down, you’re going to reference this IP

address later on.

b. Gate Address: Enter the Gate address If applicable. Enter N and hit

enter if you are going to use the 62532 on the same LAN as the PC

used to poll the data. For remote access not within the locate LAN,

TB-6108 Page 8 of 9 Revision 07/05

Employee Owned

enter Y and enter the Gateway IP address, your IT department can

supply you with the appropriate Gateway IP address.

c. Netmask: Number of bits for host 11. Netmask defines the number of

bits taken from the IP address that are assigned for the host sections.

d. Change telnet configuration password: Enter N for no. Enter Y for

yes, then type in a 4-digit password. Changes can only be made to the

50460 with a password if password is set to Yes.

8. Enter 1 for Channel 1 Configuration.

a. Baudrate = 9600

b. I/F Mode = 5B (serial RS-485) / 58 (serial RS-232)

c. Flow = 0

d. Port No = 14001 or 1400X (x=1...9)

e. Connect Mode = C5

f. Remote IP address = 0

g. Remote port = 0

h. DisConn Mode = 0

i. Flush Mode = 0

j. DisconnTime = 0

k. SendChar 1 = 0

l. SendChar 2 = 0

Select 9 to save and exit. (Figure 10).

9. Verify the IP address:

•Go to the DOS prompt.

•Type: ping <IP address>.

•If there is a reply, then the IP address has been assigned successfully. If there

is no response, please go back to A.

C.Redirector Software Setup

Comport redirector will need to be downloaded from Lantronix ®.

Go to www.lantronix.com and downloads. Then scroll down to Software/Configuration

Utilities, you should see Com Port Redirector, click on the lastest version and start

downloading. Save it in your Smartlog™ Folder.

Once you are done downloading, Windows will ask you if you want to install it, click yes.

Once Installation is completed, open your Lantronix ® Com port Redirector.

TB-6108 Page 9 of 9 Revision 07/05

Employee Owned

Figure 8. Lantronix RDCfg Main Menu

1. The software will default one open com port to be use, usually it’s com 3

if your PC system isn’t using com 3.

2. Click on Add IP

•Enter the IP address that was assigned to the Ethernet adapter

62532 in the box Host.

•Subtract 11000 from Port No. to get TCP Port, refer to 8. Enter 1

for Channel 1 Configuration. d. Usually TCP Port 3001

•Click Ok, save and eixt.

3. Open the software you are currently using or Smartlog 6.03 and configure your

comport in the software to match the comport of the Lantronix Redirector

software.

TB-6108 Page 10 of 9 Revision 07/05

Employee Owned

TECHNICAL SUPPORT:

USA

Semtronics

3651 Walnut Avenue

Chino, CA 91710

Tel: (909) 627-8178

Fax: (909) 627-7449

NOTE: Unauthorized servicing or modifications to your monitor will void the product warranty

and may create dangerous conditions. Servicing should be performed only at the factory, or

by a Semtronics approved technician.

LIMITED WARRANTY

Semtronics expressly warrants that for a period of one (1) year from the date of purchase Semtronics

62532 will be free of defects in material (parts) and workmanship (labor). Within the warranty period,

a unit will be tested, repaired, or replaced at our option, free of charge. Call Customer Service at 909-

627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for Return Material Authorization (RMA) and

proper shipping instructions and address. Include a copy of your original packing slip, invoice, or other

proof of date of purchase. Any unit under warranty should be shipped prepaid to the Semtronics

factory. Warranty replacements will take approximately two weeks.

If your unit is out of warranty, Semtronics will quote repair charges necessary to bring your unit up to

factory standards. Call Customer Service at 909-627-8178 for proper shipping instructions and

address. Ship your unit freight prepaid.

WARRANTY EXCLUSIONS

THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT

WARRANTIES, EXPRESSED AND IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. The express warranty will

not apply to defects or damage due to accidents, neglect, misuse, alterations, operator error, or failure

to properly maintain, clean or repair products.

LIMIT OF LIABILITY

In no event will Semtronics or any seller be responsible or liable for any injury, loss or damage, direct

or consequential, arising out of the use of or the inability to use the product. Before using, users shall

determine the suitability of the product for their intended use, and users assume all risk and liability

whatsoever in connection therewith.

Indice

Altri manuali Semtronics Adattatore

Semtronics

Semtronics 62533 Manuale utente

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente