Seneca MyBoat Manuale utente
SENECA s.r.l.
Via Austria, 26 – 35127 – PADOVA – ITALY
Tel. +39.049.8705355 - 8705359 - Fax +39.049.8706287
For manuals and configuration software, visit www.seneca.com/myboat
MI004981-E INSTRUCTIONS IN ORIGINAL LANGUAGE ENGLISH - 1/7
E
E
INSTALLATION MANUAL
MyBoat
Real time remote control and alarm
management device for boats
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds with the products and technologies described. Data herein may
be modified or supplemented for technical and/or sales purposes.
MODULE LAYOUT
Weight 150 g Case Polycarbonate / ABS material.
LED SIGNALS ON THE FRONT PANEL
LED STATUS LED MEANING
GSM
(Yellow)
Off MyBoat off
Medium flash (64 ms ON / 800 ms OFF)
Network search
No signal
SIM card with incorrect pin
Slow flash (64 ms ON / 3000 ms OFF)
Registration to the GSM network
successful
Fast flash (64ms ON / 300 ms OFF)
Successful access to the Internet
network
Correct APN
Registration to the GPRS network
successful
PWR
(Green)
On
Off
MyBoat on
MyBoat off
PRODUCT DESCRIPTION
MI004981-E ENGLISH - 2/7
80 mm
108 mm
32 mm
8 mm
MyBoat is a flexible control system consisting of a smart control unit and wireless monitoring sensors for
the remote control and alarm management in real time of yachts, boats and general and fleet. As well as
managing the communication with the sensors and the SENECA cloud platform, the control unit is set for
the advanced configuration and optional remote control of 4 digital inputs, 1 timed relay output (e.g.
siren), 1 non-timed relay output (auxiliary), 1 analogue input for service battery sensor (already wired to
the control unit power supply) and 1 fuel level analogue input. For information on the functions of your kit,
refer to the summary table on the package.
PRELIMINARY WARNINGS
ASSEMBLY STANDARDS
SYMBOLS ON THE ENCLOSURE
PWR power button
Slot for mini SIM
GSM antenna Micro SD card slot
Scroll display button (SCR)
Micro USB connector
TECHNICAL SPECIFICATIONS
POWER SUPPLY
Voltage
absorption
Internal battery (buffer)
6 – 15 V , 500 mA Max.
3.5 W Max.
Lithium Ion 3.7 V - 1000 mAh, rechargeable.
ENVIRONMENTAL CONDITIONS
Temperature
Humidity
Storage temperature
Protection rating
Seneca recommends use at 0 to 45 ° C for correct operation.
With the power supply present: -20 .. + 55 °C.
With use of the battery (when discharged): -20 .. + 45 ° C.
Charging is possible in the range: 0 .. +45°C.
30% – 90%, non condensing.
from -20 °C to +20 °C <1 year; from -20 °C to +45 °C <3 months;
from -20 °C to +60 °C < 1
month IP20
MI004981-E ENGLISH- 3/7
SD
SIM
Electrical and electronic waste disposal (applicable in the European Union and other countries
with recycling programs). The symbol on the product or its packaging shows that the product
must be disposed of at a collection centre authorised to recycle electrical and electronic waste.
The full content of this manual must be read before operation. The device is to be
exclusively used by qualified electricians.
Damaged parts must be replaced by the manufacturer, who is also responsible for repairing the
device. The product is sensitive to electrostatic discharges. Take appropriate measures during
operation.
The warranty shall become null and void in the event of improper use or tampering with the
device or accessories supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
For optimum reception of the GPS signal from satellites, it is best to place the MyBoat horizontally in an area
not covered by metal structures. If this is not possible, an optional external antenna with 3m cable (code
AGPS) is available. Follow the procedure supplied with the package for the installation of the external
antenna.
BASIC CARD SPECIFICATIONS
DIGITAL INPUTS
Type
Maximum frequency
Threshold OFF
Threshold ON
4 inputs
Reed, contact, PNP, Pulscap
30 Hz
ANALOGUE INPUTS
Accuracy
type
2 inputs
Voltage 0 - 30 V / Current 0 - 20 mA
0.1% of the full scale
VOLTAGE OUTPUT: +12 V 50 mA (maximum current)
TEMPERATURE SENSOR NTC thermistor
USB PORT 1 reserved micro USB port
DISPLAY
CONNECTIONS
CPU ARM 100 Mhz 32 bit
INTERNAL MEMORY FLASH 2 MByte (log)
Micro SD slot Type/ Memory Push-Push for SD card and SD HC card / max 32GB
SIM slot Type Push-Push for mini SIM (15 x 25 mm)
MMCX CONNECTOR External GPS antenna connector (optional)
GSM Quad band (850 / 900 / 1800 / 1900 MHz)
GPS CARD SPECtIFICATIONS
RECEIVER 22 channels
SENSITIVITY -165 dBm
FIX TIME 32 s usually
ACCURACY up to 2.5 m
RECEIVER AND SENSOR SPECIFICATIONS
TECHNOLOGY LoRa ®
FREQUENCY BANDS 863 ÷ 870 MHz
SENSITIVITY up to -146 dBm
RF POWER + 14 dBm
RELAY EXPANSION CARD SPECIFICATIONS (OPTIONAL)
REFERENCE STANDARDS
MI004981-E ENGLISH- 4/7
STANDARD ETSI EN 301 489-7
EN301 511
EN301 489-1
IEC / EN 60950
DIGITAL
OUTPUTS
2 outputs
Relay 3 A max - 250V SPST (with shared terminal)
0 - 3 V, I < 1 mA
6 - 24 V, I > 3 mA
128 x 32 LCD Dots with visible area of 39 mm x 8.6 mm
Spring clamps, 3.5 mm pitch, connector for Micro USB and SMA
connector for GSM Antenna
•
ON/OFF BUTTON AND SCROLL DISPLAY BUTTON
•
MICRO USB PORT AND POWER SUPPLY
•
AUTO SHUTOFF
INSERTING THE SIM CARD AND SD CARD
•
INSERTING THE SIM CARD
•
INSERTING THE MICRO SD CARD
MI004981-E ENGLISH - 5/7
INITIAL POWERING ON OF THE DEVICE
ANTENNA
micro
USB
PWR SCR
ANTENNA
SIM
card
SD
card
MyBoat is supplied in "shipping mode".
This mode avoids any unnecessary discharge of the battery during storage and shipping.
When switched on for the first time, power the device with the power cord supplied;
this allows "shipping mode" to be exited.
MyBoat is equipped with a PWR button located on the top left side (front
panel view). Pressing this button turns the module on and off. To switch it
off, hold the PWR key down for a few seconds.
MyBoat is also equipped with a SCR button, located on the top right side
(front panel view). Pressing this key displays the parameters.
The device has a micro USB connector on the left side of its enclosure,
which can be used for configuration, firmware updates and to recharge the
internal battery.
To recharge the internal battery, use:
- the power cord with cigarette lighter socket, equipped with a fuse
connecting the cables to the + and- (GND) terminals.
- a PC via the micro USB port with a standard cable.
Power supply through the USB jack is not suitable for fixed installations, or
configurations where relays and/or digital inputs are used.
If the display indicates "LOW BAT", it means that the internal battery is almost
empty: after 60 seconds from this indication, the device switches off automatically.
To restore the battery charge to an appropriate value, power the
device using one of the recommended modes.
MyBoat has an entry for mini SIM located in the right side of the enclosure.
To insert the card in its corresponding slot, make sure the metal contacts are facing
right (as seen in the figure).
MyBoat is equipped with an SD card input that can be used to update the
device's firmware and update the information and connection parameters with
the world's best known telephony operators.
Note: DO NOT REMOVE THE CONTENT OF THE SD CARD PROVIDED. THIS
MAY RESULT IN FAILED DATA CONNECTION WITH THE MYBOAT
SERVICE.
The input for micro SD card is located on the right side of the enclosure.
To insert the SD card in its corresponding slot, make sure the metal contacts are
facing right (as seen in the figure).
SAFETY INFORMATION
ELECTRICAL CONNECTION
MI004981-E ENGLISH - 6/7
•
INSERTION AND EXTRACTION FROM TERMINALS WITH A PUSH-WIRE
Insertion o
a rigid cable
f
Press down Recommended
flaying: 8-9 mm
Insertion o
a flexible
cable
f
A Press with
screwdriver
B Insert the
cable
Extraction
of a cable
A Press with
a screwdriver
B Extract
the cable
•
PUSH-WIRE TERMINAL BLOCK
(timed) AUX1
Shared of the two relays
(not timed) AUX2
1
2
3
(normally closed) DIN4
AUX + 12 Vdc
(service battery sensor) AIN 1
0 V= 0%; 10 V = 100% NTC
4
5
6
7
8
9
10
1
GND
(Sensor input) NTC
+ Power
- Power
12
13
+
-
1 2
3
45 6 78 9 10 11 12 -
+
13
MyBoat has a terminal block inside its enclosure.
To access the internal terminal block of the device, unscrew the screw at the
centre of the black cover positioned at the bottom of the enclosure and lift up.
In the side figure, the cover has been removed.
IMPORTANT: With the relay card, mobile wiring of cables connected to
terminals is not permitted. To make the cables from the terminals safe, use the
break-out passages in the back of the enclosure. When the wiring is complete,
fasten the protective cover on the device with the screw to prevent any
accidental contact.
(normally closed) DIN3
(normally closed) DIN2
(normally closed) DIN1
ACCESSORIES
OPTIONAL ACCESSORIES
External GPS antenna with 3 m cableA-GPS
A-GSM/QUAD-N
CPS-TIP-MP
MYBOAT-S1
MYBOAT-S2
MYBOAT-S3
MYBOAT-S4
MYBOAT-S5
MYBOAT-S6
MYBOAT-S7
MYBOAT-S8
External GSM / QUAND-N antenna with 5 m cable
SPARE ACCESSORIES
Spare cigarette lighter power supply
Replacement sensor for access control
Replacement sensor for bilge monitoring
Replacement sensor for access control
Replacement sensor for battery monitoring
Replacement sensor for battery monitoring
Replacement sensor for bilge monitoring
Replacement sensor for access control
Replacement sensor for access control
CONTACTS
Product information sales@seneca.it
MI004981-E ENGLISH - 7/7
Altri manuali per MyBoat
2
Indice
Altri manuali Seneca Adattatore
