Seneca R-COMM Manuale utente
MI00564-0-EN INSTALLATION MANUAL 1/4
INSTALLATION MANUAL
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualied electricians. Specic documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.
The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
CONTACT INFORMATION
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modied or supplemented for technical and/or sales purposes.
DOCUMENTATION
R-COMM
R-COMM
MI00564-0-EN INSTALLATION MANUAL 2/4
MODULE LAYOUT
LED STATUS LED meaning
On Signal level reporting
Flashing Modem not correctly adjusted
NET
On Modem adjusted on 4G network
Flashing Modem adjusted on 2G or 3G network
Off Modem off or not adjusted
DATA
On Data connection enabled and correctly adjusted
Flashing Data connection enabled but in error
Off Data connection disabled
GPS On GPS signal present
Off GPS signal absent
BAT
On Battery connected and working properly
Flashing Low or faulty battery
Off Battery not in use (UPS not active)
PWR On Module powered / successful connection
Off Module not powered / instrument not connected
SIGNALS VIA LED ON FRONT PANEL
Weight: 80 g; Enclosure: UL94-V0 self-extinguishing PC/ABS material, black.
95mm
53mm 32mm
MOBILE
ANT.
GPS
ANT.
MI00564-0-EN INSTALLATION MANUAL 3/4
TECHNICAL SPECIFICATIONS
CERTIFICATIONS
https://www.seneca.it/products/r-comm/doc/CE_declaration
POWER SUPPLY Through connection with the main module
BACKUP BATTERY
(R-COMM-B-4GWW ONLY)
Nickel battery
AA dimension
1250mAh; 3.6V
ENVIRONMENTAL CONDI-
TIONS
Temperature: -25°C ÷ +65°C
Humidity: 30% ÷ 90% non-condensing
Storage temperature: -30 °C ÷ + 85 °C
Protection rating: IP20
ASSEMBLY DIN rail 35 mm IEC EN60715 or wall with screws
CONNECTIONS
1 SIM-CARD slot
1 SMA connector for GPS antenna
1 SMA connector for 4G/LTE antenna
4G MODEM FREQUENCIES
Global coverage Model 4G/LTE
LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/ B19/B20/B25/B26/B28
LTE-TDD: B38/B39/B40/ B41
WCDMA: B1/B2/B4/B5/B6/B8/B19/GSM: B2/B3/B5/B
OUTPUT POWER
GSM900: 32.75dBm, DCS1800: 29.07dBm, WCDMC: 23.13dBm, 23.27 dBm, LTE:
23.1dBm, 23.2dBm, 21.7dBm, 23.19dBm, 23.14dBm, 23.7dBm, 23.39dBm.
GNSS
GPS / GLONASS / BeiDou (compass) / Galileo / QZSS
SIM CARD SLOT
Push-push type for mini SIM card 15 X 25 mm
UPS BUTTON OFF (R-COMM-B-4GWW ONLY)
Button used to switch the UPS off:
The button is located on the underside of the instrument.
To shut down the UPS of the device, simply press the OFF button, in doing so the power supplied by the battery
pack for the UPS will be disabled.
To switch off the R-PASS main module, it is necessary to disconnect the power cables from the terminals.
N.B.: To purchase the "GPS antenna" accessory, access the website www.seneca.it and go to the product page.
MI00564-0-EN INSTALLATION MANUAL 4/4
CONNECTION TO THE MAIN MODULE
INSTALLATION ON DIN-IEC EN 60715 RAIL
Installation:
Position the device on the OMEGA rail resting the upper
teeth from top to bottom.
Push the lower part towards the rail until the locking sys-
tem engages.
Removal:
After switching off the module, with the help of a slotted
screwdriver, unlock the locking system located on the
underside of the instrument.
Installation:
To connect the R-COMM accessory module to the R-PASS main module, position the instrument on the DIN rail as shown
in the procedure below, then slide the module until it is fully engaged with the side connector.
After the correct connection, the PWR led turns on to show the power supply.
The connection of the R-COMM accessory module must be made with the R-PASS main module turned off.
N.B.: For an ideal operation of the module, the use of a DIN rail clamp is recommended.
CAUTION
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Seneca Sistema di conferenza
Manuali Sistema di conferenza popolari di altre marche
Kramer
Kramer VIA GO Manuale utente
AVT
AVT MAGIC AC1 Go Manuale utente
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manuale utente
Sony
Sony PCS-I150 Manuale utente
Middle Atlantic Products
Middle Atlantic Products VTC Series Manuale utente
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guida
