Seneca SURPRISE Manuale utente

INSTALLATION MANUAL

SURPRISE Smart Display

Display HMI touchscreen with IoT, Gateway built-in I/O

SENECA s.r.l.

Via Austria, 26 – 35127 – PADOVA – ITALY

Tel. +39.049.8705355 - 8705359 - Fax +39.049.8706287

For manuals in other languages and conguration software, visit:

www.seneca.it/products/surprise-smart-display

MI00542-1-EN 1/6

DOCUMENTATION

192mm

127mm

32mm

MODULE LAYOUT

Dimensions (LxHxD) 192 x 127 x 32 Weight 420 g Protection rating IP 64

2/6

WARNING: The full content of this manual must be read before any operation. The module must only be used by

qualied electricians. Specic documentation is available via QR-CODE shown on page 1.

Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).

The symbol on the product or its packaging shows the product must be surrendered to a collection centre

authorized to recycle electrical and electronic waste.

The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to

electrostatic discharges. Take appropriate measures during any operation.

PRELIMINARY WARNINGS

The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.

The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the

instrument or the connected equipment. The warranty shall become null and void in the event of improper use or

tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if

the instructions contained in this manual are not followed.

GENERAL SPECIFICATIONS

Smart Display is a 7-inch HMI touch-sensitive colour display (capacitive touch panel), with 800 x 480

resolution and LED backlight.

It is also an operator terminal designed to control and monitor the operation of devices, systems or

production lines.

Smart Display also offers extended connectivity thanks to the functionalities of Industrial Gateway, Serial

Device Server, Bridge and optional WIFI.

The preloaded software application allows the display of parameters, the sending of commands, the

conguration of tags, communication, individual video pages and alarm management.

TECHNICAL SPECIFICATIONS

STANDARDS

EN300 328 Wideband transmission systems.

EN301 489-17 EMC Specic conditions for Data Transmission Systems.

EN301 489-1 EMC Common technical requirements for radio equipment.

EN60368-1, EN62311 Safety

POWER SUPPLY

Voltage

Absorption

24 Vac/dc ± 10%

AC: Max. 16 VA, 10 W; DC: Max. 9W (maximum brightness)

N.B.: Arrange a power supply with at least 1.5 A inrush

DISPLAY

Resolution

Brightness

Contrast

Duration

Viewing angles

RTC

800 x 640, technology: TFT, 16 M colours

350 cd/m2

500 : 1

30000 h (backlight level = 5)

70° / 50° / 70° / 70° (Top, Bottom, Left, Right)

YES

CONNECTIONS

ELECTRICAL

1 removable terminal 3.5mm pitch 10-way, 1.5 mm2 max cable section

2 micro USB connectors

2 RJ45 connectors (Ethernet ports)

ENVIRONMENTAL CONDITIONS

Operating temperature

Humidity

Storage temperature

Protection rating

From -20°C to +55°C

10%– 90% non condensing.

From -30°C to +55°C

IP64 (referred to the front and with gasket installed)

COMMUNICATION PORTS

2 x Fast Ethernet 10/100Tx ports on RJ45

1 x RS232/RS485 software switchable serial port

1 x RS485 serial port

1 x USB OTG port

1 x USB serial port for debugging software

1 x Wi-Fi 802.11 b/g/n, band 2.4 ÷ 2,4835 GHz, max Output Power: 17 dBm (50 mW)

2 x General Purpose Input or Output channels

AUXILIARY VOLTAGE

INPUT/OUTPUT See explanatory diagrams on page 5

GENERAL PURPOSE I/O

Number of channels: 2

Input voltage: 0÷28 V Threshold ON > 9 V

Input impedance: 9 kΩ Threshold OFF < 4 V

ASSEMBLY

Using xing brackets or wall bracket

The Declaration of Conformity ( DoC) is available at www.seneca.it/surprise-smart-display.

3/6

WAN LAN

TERMINAL BOARD 1-8

USB

OTG

USB

DEBUG

DISPLAY BACK

VIEW

DRILLED PANEL

FIXING

BRACKET

DRILLING THE PANEL

157mm

102mm

4/6

INSTALLATION REGULATIONS

For secure xing use all four brackets provided.

In case of use in environments with the presence of water, use the supplied gasket.

The minimum thickness of the panel is 1 mm and the maximum thickness is 15 mm.

For the assembly: make a rectangular opening on the panel measuring: W=157 mm x H=102 mm.

Place the display on a stable surface, screw the 4 studs into the threaded inserts of the display, insert the 4 brackets and

x them to the display using the 4 white knobs.

Fastening the brackets as in the gure allows the easy insertion into the opening made on the panel.

Insert the display into the panel opening and x it by turning the brackets as shown in the gure.

Be careful not to drop the panel during xing to avoid damaging it.

SW1

For wall mounting use the outer holes of the xing accessory as shown in the picture below

(N.B.: the wall mounting accessory is supplied already assembled to the instrument, in case of wall mounting it must be

removed avoiding to make levers in order not to damage the plastic):

N.B.: DO NOT INSTALL THE INSTRUMENT AT A HEIGHT EXCEEDING 2m.

WALL-MOUNTING REMOVAL OF THE ACCESSORY FIXING

Important: The upper power supply limits must not be exceeded, as this could cause

serious damage to the module. Switch the module off before connecting inputs and outputs.

To meet the electromagnetic immunity requirements:

- use shielded signal cables;

- connect the shield to a preferential instrumentation earth system;

- separate shielded cables from other cables used for power installations

(transformers, inverters, motors, induction ovens, etc...)

POWER SUPPLY

The power supply is connected to terminals 1 and 2.

The supply voltage must be:

24 Vdc (indifferent polarity) or 24 Vac.

Use a power supply with a minimum current of 1 A

GENERAL PURPOSE INPUT

The inputs are PNP type with internal power supply,

the gure alongside shows the connection.

To use the INPUT or OUTPUT function it is

necessary to congure the dedicated port through

the dedicated conguration page.

The inputs can also be activated in voltage,

ON > 9 V, OFF < 4 V

GENERAL PURPOSE OUTPUT

Connection with internal power

12 V / 50 mA per output.

Connection with external power

12÷24 V / 100 mA per output.

SERIAL PORTS

The device has a COM1 port congurable as RS232

or RS485 on terminals 7 and 8 and a COM2 RS485

port on terminals 9 and 10.

Power supply 1

Power supply 2

COM1 485B/232RX 7

COM1 485A/232TX 8

COM2 485 B 9

COM2 485 A 10

GND 4

Auxiliary voltage output 3

GND 4

GPIO1 5

GPIO2 6

GND 4

GPIO1 5

GPIO2 6

LOAD

ELECTRICAL CONNECTIONS

5/6

GND 4

GPIO1 5

GPIO2 6

0 V

Auxiliary voltage input 3

GND 4

GPIO1 5

GPIO2 6

LOAD

12÷24 V

0 V

12÷28 V

WARNING

A wired emergency stop button must be installed in any human-machine interface system such as this

display in compliance with ICS safety recommendations.

If used as an operator panel for machines, check the applicable safety standards.

CAUTION

Do not power the HMI display and DC inductive loads or controller input circuits, with the same power

supply. Some controllers generate 24 Vdc but do not provide enough current to be able to power this

HMI display which, when turned on, generates absorption peaks greater than 1 A.

CAUTION

a. The length of the power cable must be kept to a minimum

(Max: 500m shielded, 300m unshielded).

b. If wiring occurs outdoors, use appropriate surge suppressors.

c. Properly separate the power conductors from the signal conductors.

CONTACT INFORMATION

Technical support [email protected]

Product information [email protected]

6/6

This document is the property of SENECA s.r.l. Copies and reproduction are prohibited unless authorised.

The content of this document corresponds to the described products and technologies.

Stated data may be modied or supplemented for technical and/or sales purposes.

Indice

Altri manuali Seneca Monitor

Seneca

Seneca S311D-L Series Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione