Sennheiser Sennheiser 3000 series Manuale utente

The Gradav Guide to

Sennheiser 3000 series

Radio Mics

Intro & Overview

The 3000 series of Radio Mic equipment is used in West End Theatre

productions, by Broadcasters, and those users looking for that extra quality

that is inherent in Sennheiser’s more expensive systems.

The EM 3032 dual receivers allow the user to the system. Output

level adjustment, squelch control and a comprehensive LCD display are

there for the experienced user. A headphone socket per channel is a handy

facility for all users.

Metal casings are used throughout the range giving an improved RF

performance, and a greater robustness.

Where transmitter size is important we have the SK5012, which is much

smaller than the SK50/SK3063 pocket packs. There is a small cost for the

reduction in size, and the SK5012 does not indicate battery life on the

receiver as do all the other transmitters.

This guide has been written to assist the user who is new to this system to

get the result they are looking for with the minimum of time and worry. It

will also aid the experienced user whose memory needs a little help!

Fault finding is never easy, especially when you are under pressure. We

have added a section that may just save your reputation (and sanity)!

Pocket Pack Transmitters

SK50 & SK3063

These packs are identical in operation

and are distinguished by the silver

body of the SK50 and the black body of

the SK3063.

We supply these transmitters with the

aerials fitted. The connector (1) is a

screw-lock single pin Lemo connector.

It is important that the locking ring is

tight.

Microphones to fit socket (7) are either

fitted with a screwdown connector (as

the aerial) or more frequently with a

push to insert type; where a pull on

the barrel both unlocks and removes

the connector. Never unscrew this

style of connector as internal damage

results, often leaving the connector

stuck in the transmitter. This is a 3

pin Lemo connector, to prevent acci-

dental insertion in the aerial socket

(and vice versa).

The channel selector switch (2) is

screwdriver operated. Frequency allo-

cations are as shown on the front

panel (8).

There is a multi-segment LED display on the battery pack that gives an indication of

battery life (3). See the chart above.

The ON/OFF switch (4) is recessed to avoid accidental operation. When the transmit-

ter is on the LED (5) will light. This LED will flash in the event of input (microphone)

overload. Reduce gain on the screwdriver operated input gain control (6). We find that

a setting of 3 suits most applications.

To remove the battery pack you must first squeeze the

catches either side of the trasmitter as shown. Slide the

pack downwards while continuing the pressure on the

catches. Install MN1500 (AA) batteries. Replace battery

box by sliding back into position.

SK 5012

1 2 3

We supply these transmitters with the aerials

fitted. The connector (3) is a screw-lock single pin

Lemo connector. It is important that the locking

ring is tight.

Microphones to fit socket (1) are either fitted with

a screwdown connector (as the aerial) or more

frequently with a push to insert type; where a pull

on the barrel both unlocks and removes the

connector. Never unscrew this style of connector as

internal damage results, often leaving the

connector stuck in the transmitter. This is a 3 pin

Lemo connector, to prevent accidental insertion in

the aerial socket (and vice versa).

The channel selector switch (5) is screwdriver

operated. Frequency allocations are as shown on

the panel (7).

To open the battery cover you must squeeze the catches on

either side and move towards the hinge, as shown by the

small arrows on the diagram, on the left.

When they have reached the end of their travel you can

hinge the cover open. This gives access to change the battery

set of 2 x MN2400 (AAA). Please check for polarity when

inserting.

Open this cover to give access to the controls etc as below.

Close the cover when you have finished. It will close with a

click as the catches engage. This arrangement prevents

accidental access to the controls, but the LED (2) is still

visible.

When the On/Off switch (6) is moved to the ON position, the LED (2) lights. The LED

will start to blink about 30 mins before operation will cease. The rate of blinking will

increase as the battery life diminshes.

Screwdriver switch (4) is used to adjust the input gain. We test at a setting of 3, and

find this level suits most applications. If the input is overloaded the LED (2) will flash

brightly.

This is a particularly small transmitter, with a case size of 53 x 60 x 17 mm.

Hand Held Transmitter

To change the MN1604 (PP3) battery, you

must first unscrew the capsule as shown.

Pressing against the side of the battery

compartment cover will release the lid, allow-

ing the old battery to be removed.

Replace the battery, ensuring that the rubber

transit cover has been removed from the

battery terminal, and that the correct polarity

has been observed. The transmitter terminals

have been designed to prevent operation

should the battery be inserted with the wrong

polarity.

Close the cover and replace the capsule to

ready the transmitter for operation.

Press the button briefly in the end of the

transmitter, as shown, to turn the transmitter

on. There is a delay of about 2 seconds before

the self-test checks are complete and transmis-

sion begins.

Press the button for > 1 second to turn off.

SKM 3072

Battery status is shown by a row of segments

as illustrated on the left.

8 segments Full battery life

4 segments Half battery life

1 segment Nearly flat. alternates

with the screen display.

You can always monitor battery life on the

EM3032 receiver

Press the ribbed area on the cap body (A) and

then you can remove the cover by pulling in the

direction of (B). There are a variety of different

coloured covers, which may be changed to aid

identification.

Use the

between channel number and frequency.

Using the and /

some transmitter settings.

Function SET Adjust Store

Sensitivity

note 1 1 press Press SET

> 1 sec

Channel

Change 2 presses Press SET

> 1 sec

Assign Channel

Number 3 presses Press SET

> 1 sec

Power Lock

ON 4 presses Press SET

> 1 sec

Power Lock

OFF 1 press note 2 Press SET

> 1 sec

Sensitivity changes will be heard immediately, but levels will revert after

15 seconds if the new level is not stored.

note 1

note 2

Once the Power Lock is applied, all other settings are fixed. To alter

settings, first take the Power Lock off.

Frequency Allocations

1 854.900 5 856.575 9 860.400 13 repeat

2 855.275 6 857.625 10 860.900 14 repeat

3 855.900 7 858.200 11 861.200 15 repeat

4 856.175 8 858.650 12 861.750 16 repeat

All the frequencies shown can be used together, although it is worth noting that as the

number of frequencies in use increases, so does the likelihood of external conditions

affecting system performance. Always take great care over receiver aerial placement

when using a large number of channels together.

EM 3032 Receiver

6 61

Headphone socket 6.3 mm (¼in)

Headphone volume control

LCD display panel. Shows frequency information, RF data and battery life.

Frequency selection buttons

SET button for storing a selected frequency

On/off switch (per channel)

Fuse Holder and mains voltage selection

Mains connector

Squelch adjustment

Strain relief clamp for mains cable

Service test point

Audio output on 3pin XLR (balanced)

Audio output level control

Aerial connector B

Aerial connector A

Switch on by pressing the ON/Off switch(6).

The display will light (D1) to show the frequency in use. MUTE will also be lit.

If a transmitter is operating on this frequency there will be a delay of 4 seconds

before the display will change (D2) to show RF level, deviation and receiving aerial in

use (A or B).

Press the SET button (5). The text “FREQUENCY MHZ” will flash (D3).

Using 4), select a different frequency.

Press SET (5) for > 3 seconds to store the change. Confirmation of the change is

given by “FREQUENCY MHZ” ceasing to flash and “Sto” appearing when the rest of

the display goes off briefly.

Pressing SET briefly will cancel at any time during this operation.

The SKM 3072, SK 50 and SK 3063

transmitters transmit a battery status

signal.

When 20 to 30 minutes battery life

remains, the receiver display shows

“LOW BATT” (D4).

If squelch is activated “MUTE” will

light, and the “LOW BATT” will extin-

guish. It will relight when a signal is

received from the transmitter.

Indice

Altri manuali Sennheiser Sistema microfonico

Sennheiser

Sennheiser e908 T ew Manuale utente

Sennheiser

Sennheiser RC Sheriff Trust Manuale utente

Sennheiser

Sennheiser EW 100 G3 Dimensioni

Sennheiser

Sennheiser SR 2050 IEM Manuale utente

Sennheiser

Sennheiser evolutionwireless G3 Supplemento

Sennheiser

Sennheiser EW 110 G3 - FREQUENCY SHEETS Manuale utente

Sennheiser

Sennheiser evolution wireless G3 system Manuale utente

Sennheiser

Sennheiser EW 135 G2 Manuale utente

Sennheiser

Sennheiser SK 250 Manuale utente

Sennheiser

Sennheiser EW 100 G2 Manuale utente

Sennheiser

Sennheiser EK 100 G3 Manuale utente

Sennheiser

Sennheiser 100-P - 01-09 Manuale utente

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente

Sennheiser

Sennheiser Evolution Wireles G3 SR 300 IEM Manuale utente

Sennheiser

Sennheiser Evolution Wireless G4 Manuale utente

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente

Sennheiser

Sennheiser XS Wireless Series Manuale utente

Sennheiser

Sennheiser evolution wireless g3 SKM 300 Manuale utente

Sennheiser

Sennheiser XS WIRELESS 1 Manuale utente

Sennheiser

Sennheiser ew 300 G2 Manuale utente

Sennheiser

Sennheiser IAS MO 2000 SET Dimensioni

Sennheiser

Sennheiser TOURGUIDE UHF Manuale utente

Sennheiser

Sennheiser SpeechLine Manuale utente

Sennheiser

Sennheiser WICOS DV Manuale utente

Manuali Sistema microfonico popolari di altre marche

Paso

Paso R824 Manuale utente

Naxa

Naxa NAM-982 Manuale utente

Motorola

Motorola PMNN4461 Manuale utente

Xvive

Xvive U3 Manuale utente

Tekon

Tekon DUOS Manuale utente

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuale utente

Devine

Devine WMD-IE Manuale utente

LG LF-D7150 Manuale utente

GE S768DAV Manuale utente

LD U305 HBH 2 Manuale utente

Chainway

Chainway URA8 Manuale utente

ORATOR

ORATOR D860TD Manuale utente

Alpha Technologies

Alpha Technologies RBMS Manuale utente

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuale utente

Shure

Shure UA844 Manuale utente

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente

Pyle

Pyle PDWM5000 Manuale utente

Airspan

Airspan AS4000 Guida