Sentiotec ProD DMX Manuale utente
DE
INSTRUCTIONS FOR INSTALLATION AND USE
English
Version 01/21 ID no. 1-052-819
EN
FR
IT
NL
Colour light control
ProD DMX
Pro-DMX / 1-052-786
Instructions for installation and use p. 2/8
1.About this instruction manual
Read these installation and operating instructions carefully and keep them within
reach when using the infrared control unit. This ensures that you can refer to
information on safety and operation at any time.
These installation and operating instructions can also be found in
the downloads section of our website: www.sentiotec.com/downloads.
2.Important information for your safety
The ProD DMX colour light control has been manufactured according
to the applicable safety regulations. However, hazards may arise
during use. Therefore adhere to the following safety information and
the specic warning notices in the individual chapters.
2.1. Intended use
The PROD DMX colour light control is exclusively used to control
the sentiotec LED RGBW spots/tubes by means of the sentiotec
DMX driver CC/CV
Any use exceeding this scope is considered improper use. Improper
use can result in serious injury or damage to the product.
2.2. Safety information for the installer
●It may only be tted and installed when the power has been
disconnected.
●Installation may only be performed by a qualied electrician or
similarly qualied person.
●NEVER open the device.
●For your own safety, consult your supplier in the event of prob-
lems that are not explained in sucient detail in the installation
instructions.
EN
DE
EN
FR
IT
NL
Instructions for installation and use p. 3/8
3.Product description
3.1. Scope of delivery
●ProD DMX colour light control
●Connection cable 5m (1-046-851)
●Assembly instructions
3.2. Optional accessories
●DMX driver CC (1-046-759)
●DMX driver CV (1-046-758)
●LED tubes RGBW (LED-TB-xx)
●LED spots RGBW (LED-SP-RGBW-xx)
●Power supply units LED-PWS-xx/LED-150
3.3. Product features
The PROD DMX colour light control has the following functions:
●Two colour light groups which can be operated independently or together
●Seven levels for adjusting the colour
●Seven colours to choose from: white, purple, blue, turquoise, green, yellow, red
●Colour changer which can be adjusted to seven speeds
4.Installation and connection
The PROD DMX lighting control unit can be mounted inside the sauna if the fol-
lowing points are observed:
●Install the device as far away from the sauna heater, infrared lamps or other
heat sources as possible.
●Do NOT install the device on or right next to the sauna heater or other
heat source.
●The maximum installation height in a sauna cabin is 140 cm.
●The maximum installation height in an infrared cabin is 170 cm.
●No insulating material (such as mineral wool) may be located behind the device.
●Observe the ambient conditions (see 8. Technical data on page 8)
Installation instructions, only for experts p. 4/8
4.1. Preparing for installation
Refer to Fig. 1.
1. Cut the mounting hole the cabin wall with a jigsaw.
2. The minimum installation depth for a wall cut-out is 35 mm.
3. Remove any insulation from the mounting hole.
4. Lay the connecting cable in the wall of the sauna cabin to the mounting hole
and fasten it with cable ties.
ATTENTION!
Damage to the unit
●The lighting control unit 2is splashproof (protection class IP X4).
●Work on the lighting control unit may only be carried out using a standard
screwdriver. Using a cordless screwdriver may irreparably damage the housing.
65 mm
48 mm
Fig. 1: Installation in wall cut-out
Fig. 2: Connecting the device (rear)
DC12/24V
D +
D -
GND
EN
DE
EN
FR
IT
NL
Installation instructions, only for experts p. 5/8
4.2. Connecting the device
Note Fig. 2.
1. Connect the 4-pin cable to the terminals as follows.
Red: DC 12-24 V
Yellow: D+
Grey: D-
Blue: GND
4.3. Installing the device
Note Fig. 3.
1. Insert the device into the mounting hole.
2. Screw the unit through the holes to the cabin wall using the four wood
screws provided.
3. Gently press the front panel into the housing. Ensure that the lower catches
engage noticeably.
Fig. 3: Fitting the front panel
Instructions for use for the user p. 6/8
5.Operation
5.1. Description of control elements
1 Light group selection
2 ON/OFF button
3 Brightness +/-
4Colour changer
5Colour selection
6 Display: Colour, brightness
7 Display: Light group
1
2
3
6
7
4
5
EN
DE
EN
FR
IT
NL
Instructions for use for the user p. 7/8
5.2. Activating the lighting control unit
1. Press the ON/OFF switch 2, to activate the lighting control unit.
►The last settings are activated.
5.3. Operating the functions
●Light group selection 1
► To activate light group 1, 2 or 1+2: briey press the button 1
►The selected light group is displayed in the display 7
●Brightness +/- 3
►Can be dimmed over seven levels
►The selected level is displayed in the display 6
●Colour changer 4
► To activate the colour changer: briey press the button 4
►All colours in the display 6 light up for three seconds
►Speed of the colour changer: press and hold the button 4
►The selected speed is displayed in the display 6
► To change the speed (1-7): briey press the button 4
●Colour selection 5
► To activate the colour: briey press the button
► The selected colour ashes in the display 6
► To change the colour: briey press the button 5
Instructions for use for the user p. 8/8
6.Cleaning and maintenance
6.1. Cleaning
ATTENTION!
Damage to the unit
The lighting control unit is splashproof, but direct contact with water could still
damage it.
●NEVER immerse the device in water.
●Do not pour water over the device.
►Wipe the housing with a damp cloth.
6.2. Maintenance
The colour light control does not require any maintenance.
7.Disposal
●Dispose of packaging materials in accordance with the applicable
waste disposal regulations.
●Used devices contain reusable materials as well as hazardous
substances. Therefore, do not dispose of your used device with
household waste, but do so in accordance with the locally appli-
cable regulations.
8.Technical data
Lighting control unit
Connection: 4-pin with power supply and communication lines
Supply voltage: 12-24 VDC
Output: <0.5 W
Storage temperature: -25°C to 70°C
Ambient temperature: 0°C to +100°C
Air humidity: max. 99% rel. humidity,
non-condensing!
Dimensions (W × H × D): 63 x 104 x 38 mm
Installation cut-out (W × H × D): 48 x 65 x 34 mm
MONTAGE- UND GEBRAUCHSANWEISUNG
Deutsch
Version 01/21 Ident-Nr. 1-052-819
DE
Farblichtsteuerung
ProD DMX
Pro-DMX / 1-052-786
Montage- und Gebrauchsanweisung S. 2/8
1.Zu dieser Anleitung
Lesen Sie diese Montage- und Gebrauchsanweisung gut durch und bewahren
Sie sie in der Nähe der Infrarotsteuerung auf. So können Sie jederzeit Informa-
tionen zu Ihrer Sicherheit und zur Bedienung nachlesen.
Sie nden diese Montage- und Gebrauchsanweisung auch im Download-
bereich unserer Webseite auf www.sentiotec.com/downloads.
2.Wichtige Hinweise zu Ihrer Sicherheit
Die ProD DMX Farblichtsteuerung ist nach anerkannten sicherheits-
technischen Regeln gebaut. Dennoch können bei der Verwendung
Gefahren entstehen. Befolgen Sie deshalb die folgenden Sicher-
heitshinweise und die speziellen Warnhinweise in den einzelnen
Kapiteln.
2.1. Bestimmungsgemäßer Gebrauch
Die Farblichtsteuerung PROD DMX dient ausschließlich zum Steuern
der sentiotec LED RGBW Spots / Tubes mittels sentiotec DMX-
Treiber CC / CV
Jeder darüber hinausgehende Gebrauch gilt als nicht bestimmungs-
gemäß. Nicht bestimmungsgemäßer Gebrauch kann zur Beschä-
digung des Produkts oder zu schweren Verletzungen führen.
2.2. Sicherheitshinweise für den Monteur
●Die Montage und Anschlussarbeiten dürfen nur im spannungs-
freien Zustand durchgeführt werden.
●Die Anschlussarbeiten dürfen nur durch eine Elektrofachkraft
oder eine vergleichsweise qualizierte Person ausgeführt werden.
● Önen Sie NIEMALS das Gerät.
●Bei Problemen, die in den Montageanweisungen nicht ausführ-
lich genug behandelt werden, wenden Sie sich zu Ihrer eigenen
Sicherheit an Ihren Lieferanten.
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Sentiotec Attrezzatura di illuminazione
