SEON DS2 Manuale utente
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Quick Installation and Setup Guide
Before you Begin…
This process involves mounting cameras and running cables through the vehicle interior. It is helpful to have
some familiarity with installing automotive accessories.
Warning: It is your responsibility to avoid damaging safety or electrical systems.
DS2 may interfere with on-board collision avoidance systems utilizing forward facing cameras.
Consult your vehicle's Owner's Manual or your dealer if you’re unsure whether your vehicle
uses this technology. To confirm if DS2 is compatible with your vehicle, please consult
https://community.seon.com/ds2-unsupported-vehicle-list/ or contact the Seon service team.
Impairing or interfering with the operation of an airbag is a critical safety concern. If you are not
confident in your ability to perform the procedures in this Guide, please consider contacting
Seon Support to schedule a professional installation.
Check that you received all system components:
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Step 1: Determine Installation Locations
Think about placement of cameras and the Control Unit, and confirm the positions will work for the images
you want to capture. Make sure you consider cable lengths and how they will run between components:
Cable Run
Cable Length
Camera 1 to the Control Unit
10 feet
Camera 1 to Camera 2
*an optional extension is available
(contact Seon Support)
43 inches*
Power connections to Control Unit
5 feet
Control Unit –here are a few good options:
Camera 1 - forward-facing, on the windshield; behind the mirror works well:
Ensure mirror adjustment will not be impeded.
Avoid areas with metal sun diffusers or other obstructions: mount on clear glass.
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Camera 2- on the headliner or a bulkhead (to capture passengers, driver, or cargo):
Do not mount to a surface that cannot support the camera’s weight or is subject to constant vibration.
If you want to attach to the headliner, ensure you insert something stronger than cardboard underneath
to hold the screws.
Step 2: Insert the SD Card into Camera 1
1. Use the supplied Torx security key to loosen the screw holding the SD card slot cover on the side of
Camera 1 and remove the cover.
2. Slide the SD Card into the SD card slot. The card only fits one way: push it in gently until it clicks in place.
3. Replace the slot cover and tighten the screw.
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Step 3: Mount Camera 1 on the Windshield
1. Clean the area where the mount will contact the windshield (alcohol swab is recommended).
2. Peel off the red adhesive backing from the mount.
3. Face the camera outward (SEON logo visible from inside the vehicle).
4. Ensure the camera body is aligned horizontally (not skewed).
5. Press the mount firmly to the windshield.
6. Adjust the vertical camera position to match the driver’s plane of view:
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Step 4: Mount Camera 2
1. Use the supplied Allen key to loosen the 3 set screws and separate the mounting plate from the housing.
2. Thread the cable through the plate and attach the flat side to the mounting surface with the 3 screws.
3. Re-assemble the camera/housing.
Aim the camera appropriately before fully tightening the set screws.
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Step 5: Install the Control Unit
1. Place the Control Unit in the desired location. Leave room to connect the cables.
2. Plug the Power Harness into the Power/Sensor input on the Control Unit.
3. Make the following electrical connections from the Power Harness to the vehicle:
Wire Colour/Label
Connects to…
Red/DC IN+
Battery source
Orange/ACC
Fused Ignition source/
Accessory
Black/DC IN-
Chassis ground
Step 5a (optional): Install the Alarm/Event Trigger Button
If the installation includes the optional Alarm/Event trigger button, make the following additional
connections from the Power Harness (in the diagram, the white/SENSOR IN1 wire is labeled Trigger 1 and the
green/SENSOR IN2 wire is labeled Trigger 2):
Note: The optional Alarm/Event Trigger Button (WSA20) ships with a 1x2 Micro-Fit connector. You need to
cut the Micro-Fit off of the cable before making the Power Harness connections shown below.
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Step 6: Run/Connect Camera Cables
Warning: The “A” pillar (beside the windshield) may contain an air bag. Do not attempt to run cables
down the “A” pillar unless you are sure you understand how the safety system may be affected.
Connect CAM from Camera 1 to the cable from Camera 2.
Connect OBD from Camera 1 to the IPC input on the Control Unit.
Step 7: Verify Operation
Turn on the vehicle ignition and ensure the red light on Camera 1 is illuminated, indicating the system has
power and is operational. If the red light does not come on, check the Power Harness connections.
DS2 –Two-Camera Vehicle Event Recording System
DS2 Quick Installation and Setup Guide
Part #700-1078 R5
Contact Technical Support
Service & Support
Toll-free phone
1.844.899.7366
Product Information
Web site
https://community.seon.com/ds2/
If you do not have login credentials for the Community, please contact Technical Support.
Complete Seon warranty details are available online at:
http://www.seon.com/documents/Seon-Warranty.pdf
Indice
Altri manuali SEON Apparecchiature di registrazione
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
