Setra Systems 280G Manuale utente

General Information

Your Setra transducer has been carefully calibrated before shipment to you and, it should be handled

with the same care given any precision instrument. Pressure ranges and dimensions are reported on

the specication bulletin for the transducer.

Installation

Do not use in ambient conditions corrosive to stainless steel, submerge in liquids, subject to spray

or drip, or in a high vibration environment. The 280G Series is slightly sensitive to acceleration in

the pressure tting axis, less than 0.05 psi/g typical. Factory calibrated in the vertical position, with

pressure port downward, this position often minimizes potential damage from dripping of pressure

system piping.

Installation of pressure tting:

For very high pressure we suggest using a sealant such as Loctite hydraulic sealant. For other pressure

ranges, standard sealants such as Teflon pipe tape generally are satisfactory. For the most sensitive

pressure ranges, excessive torquing of a metal pressure tting may cause slight zero shift which may

be trimmed out using zero adjustment. Use of plastic ttings often shows no noticeable zero shift.

The torquing effect does not appreciably affect linearity or sensitivity. Use the wrench flats on the

280G when attaching to ttings.

Atmospheric Reference (Gauge pressure units only)

Lower range units are subject to excessive thermal zero shift unless vented to atmosphere. The 280G

Series gauge pressure transducers and transmitters are vented to atmosphere at the terminal strip.

Electrical Connections

280G (.08 - 5.08 VDC output)

For 24 VDC Excitation (Nominal)

+ IN Connect to 12-30 VDC Power Supply.

+ OUT Connect to Control of Pressure Monitor.

COM. Connect as Common Return Lead for + IN

and + OUT.

CAUTION:

Care must be taken when installing this transducer that the excitation voltage is not applied to the

output lead by mistake. Excitation power, or voltage in excess of 30 VDC, inadvertently applied to

the output lead may damage the electrical circuit. Shielding or other precautions should also be

provided to assure that transient voltages in excess of 30 VDC are not applied to the output lead.

Wiring

Current Output (4-20 mA)

The circuit is designed to operate as a true two-wire 4 to 20 milliampere pressure transmitter

and will deliver rated current into any external load between zero and 800 ohms.

Operating Instructions

Model 280G Pressure Transducer and Pressure Transmitter

Three-Wire, Voltage Output—Two Wire, Current Output

CAUTION:

The 280G Series is designed to have current flow in one direction only — please observe polarity.

We suggest that the electrical cable shield be connected to the system's loop circuit ground, thereby

improving electrical noise rejection.

Excitation

• Minimum supply voltage (VDC) = 9 + 0.02 x (resistance of receiver plus line).

• Maximum supply voltage (VDC) = 30 + 0.004 x (resistance of receiver plus line).

• Calibrated at factory using a 250 ohm load at 24 VDC.

• Variations in the power supply voltage cause less than 0.02 mA change in the transmitter’s

current output, per volt change in the power supply.

Calibration

Every model 280G is factory calibrated and should require no eld adjustment. Whenever possible,

any zero and/or span offsets should be corrected by software adjustments in the user’s control sys-

tem. However, both zero and span adjustments are accessible by removing the pan head screws and

turning the zero and span potentiometer screws inside. Pan Head screws should be replaced after

adjustment to maintain enclosure rating. Voltage output units are factory calibrated into a 50 K load.

Voltage units are operable into a 5000 load or greater. The zero factory setting is ±50 mV. Current

outputs units (4-20 mA) are factory calibrated with a 24 VDC loop to supply voltage and a 250 load.

The zero factory setting is a ±0.08 mA. The span (full scale) factory settings is ±0.16 mA. Zero and

span adjustment are approximately ±1.0 mA.

Returning products for repair

Please contact Setra (1-800-257-3872, 978-263-1400) before returning unit for repair to review in-

formation relative to your application. Many times, only minor eld adjustments may be necessary.

When returning a product to Setra, the material should be carefully packaged and shipped prepaid to:

Setra Systems, Inc.

159 Swanson Road

Boxborough, MA 01719

Attn: Repair Department

To assure prompt handling, please supply the following information and include it inside the package

of returned material:

1. Name and phone number of person to contact.

2. Shipping and billing instructions.

3. Full description of the malfunction.

4. Identify any hazardous material used with product.

NOTES:

Please remove any pressure ttings and plumbing that you have installed and enclose any required

mating electrical connectors and wiring diagrams.

Allow approximately 3 weeks after receipt at Setra for the repair and return of the unit. Non-warranty

repairs will not be made without approval and a purchase order to cover repair charges.

Calibration Services

Setra maintains a complete calibration facility that is traceable to the National Institute of Standards

& Technology (NIST). If you would like to recalibrate or recertify your Setra pressure transducers or

transmitters, please call our Repair Department at 1-800-257-3872 (978-263-1400) for scheduling,

cost and turnaround estimates.

Limited warranty & limitation of repair

SETRA warrants its products to be free from defects in materials and workmanship, subject to the

following terms and conditions: Without charge, SETRA will repair or replace products found to be

defective in materials or workmanship within the warranty period; provided that:

a) the product has not been subjected to abuse, neglect, accident, incorrect wiring not our

own, improper installation or servicing , or use in violation of instructions furnished by SETRA;

b) the product has not been repaired or altered by anyone except SETRA or its authorized

service agencies;

c) the serial number or date code has not been removed, defaced, or otherwise changed; and

d) examination discloses, in the judgment of SETRA, the defect in materials or workmanship

developed under normal installation, use and service;

e) SETRA is notied in advance of and the product is returned to SETRA transportation

prepaid.

Unless otherwise specied in a manual or warranty card, or agreed to in a writing signed by a SETRA

ofcer, SETRA pressure and acceleration products shall be warranted for one year from date of sale.

The foregoing warranty is in lieu of all warranties, express, implied or statutory, including but not limited

to, any implied warranty of merchantability for a particular purpose. SETRA’s liability for breach of

warranty is limited to repair or replacement, or if the goods cannot be repaired or replaced, to a refund

of the purchase price. SETRA’s liability for all other breaches is limited to a refund of the purchase price.

In no instance shall SETRA be liable for incidental or consequential damages arising from a breach of

warranty, or from the use or installation of its products. No representative or person is authorized to

give any warranty other than as set out above or to assume for SETRA any other liability in connection

with the sale of its products.

Setra Systems, Inc.

159 Swanson Road, Boxborough, MA 01719

800.257.3872 • www.setra.com

SS-280G Rev. A 07/2017

Indice

Altri manuali Setra Systems Trasduttore

Setra Systems

Setra Systems 550 Manuale utente

Setra Systems

Setra Systems 526 Manuale utente

Setra Systems

Setra Systems 278 Manuale utente

Setra Systems

Setra Systems 278 Manuale utente

Setra Systems

Setra Systems 205-2 Manuale utente

Setra Systems

Setra Systems 265 Manuale utente

Setra Systems

Setra Systems 470 Manuale utente

Setra Systems

Setra Systems Multi-Sense 231 Manuale utente

Setra Systems

Setra Systems 223 Manuale utente

Setra Systems

Setra Systems 267 Manuale utente

Setra Systems

Setra Systems 355X Series Guida del prodotto

Setra Systems

Setra Systems 225 Manuale utente

Setra Systems

Setra Systems GCT225 Manuale utente

Setra Systems

Setra Systems 567 Manuale utente

Setra Systems

Setra Systems 209 Manuale utente

Setra Systems

Setra Systems Multi-Sense 260 Series Manuale utente

Setra Systems

Setra Systems 269 Manuale utente

Setra Systems

Setra Systems 209 Manuale utente

Setra Systems

Setra Systems 230 Manuale utente

Setra Systems

Setra Systems MS1 Manuale utente

Setra Systems

Setra Systems 264 Manuale utente

Setra Systems

Setra Systems 267 Manuale utente

Setra Systems

Setra Systems Multi-Sense 231RS Manuale utente

Setra Systems

Setra Systems 204 Manuale utente

Manuali Trasduttore popolari di altre marche

HBM

HBM AD101B Manuale utente

Camille Bauer

Camille Bauer SINEAX F534 Manuale utente

Trane

Trane KIT 16724 Istruzioni per il montaggio

Lumel

Lumel P18 Manuale utente

B&C Speakers

B&C Speakers DE75PTN Manuale utente

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Manuale

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Manuale utente

ProMinent

ProMinent Dulcometer DMT Manuale utente

MKS

MKS MicroPirani 925 Series Come usare

WIKA

WIKA WU-20 Manuale utente

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Manuale utente

Camille Bauer

Camille Bauer SIRAX CH-5610 Manuale utente

WIKA

WIKA F2802 Manuale utente

Veris Industries

Veris Industries PW Series Manuale utente

HBM

HBM TJ1-S6 Manuale utente

Simrad

Simrad ES120-7C - REV D Guida utente

HBM

HBM C18 Manuale utente

Airmar

Airmar M260 Manuale di istruzioni