SEW-Eurodrive CMP40 Manuale utente

Drive Technology \ Drive Automation \ System Integration \ Services

Revision

Synchronous Servomotors

CMP40 – CMP100

CMPZ71 – CMPZ100

Edition 07/2010 19352816 / EN

2Revision of the Operating Instructions – Synchronous Servomotors CMP40 - 100, CMPZ71 - 100

1Measuring the working air gap of the BY brake

Revision

Synchronous Servomotors CMP40 - 100, CMPZ71 - 100

1 Revision

1.1 Measuring the working air gap of the BY brake

The working air gap can be measured via the stroke of the pressure plate when the

brake is released. The permitted working air gap for brake sizes BY2, BY4 and BY8 is

0.15 – 0.6 mm. If the working air gap exceeds 0.6 mm, the brake will have to be

replaced.

The working air gap cannot be adjusted.

INFORMATION

This revision describes amendments made to the operating instructions "Synchronous

Servomotors CMP40 – 100, CMPZ71 – 100" (part number 16907213/EN, edition

07/2010). The following chapters are amended:

• Chapter 7.2: "Notes on the BY brake", page 67

Please use the data and descriptions made in this chapter. This document does not

replace the above mentioned operating instructions.

INFORMATION

Customers can check the working air gap for inspection purposes.

Revision of the Operating Instructions – Synchronous Servomotors CMP40 - 100, CMPZ71 - 100 3

1

Measuring the working air gap of the BY brake

Revision

1.1.1 Brake with manual brake release

1. Isolate the motor and brake from the power supply and safeguard them against

unintentional power-up.

2. Remove the forced cooling fan, if installed.

3. Connect the brake to the power supply.

4. Release and apply the brake electrically. When doing so, measure the stroke ∆H of

the pressure plate at the studs. This stroke ∆H corresponds to the working air gap.

4386101131

ΔH

4Revision of the Operating Instructions – Synchronous Servomotors CMP40 - 100, CMPZ71 - 100

1Measuring the working air gap of the BY brake

Revision

1.1.2 Brake without manual brake release

1. Isolate the motor and brake from the supply and safeguard them against uninten-

tional power-up.

2. Remove the forced cooling fan, if installed.

3. Remove the closing caps [1] from the two boreholes.

4. Insert one screw each into the boreholes.

SEW-EURODRIVE recommends the following screws:

5. Connect the brake to the power supply.

6. Release and apply the brake electrically. When doing so, measure the stroke ∆H of

the pressure plate at the studs. This stroke ∆H corresponds to the working air gap.

7. Remove the two screws when you have finished measuring the working air gap.

8. Close the two boreholes with new closing caps [1].

The following table shows the part numbers for the replacement closing caps:

Brake sizes Screw size Part number

BY2, BY4 M5x75 1328 145 3

BY8 M6x70 0011 834 6

Brake sizes Part number

BY2, BY4 1328 148 8

BY8 1322 534 0

4386103563

[1]

[1]

Altri manuali per CMP40

4

Questo manuale è adatto per i seguenti modelli

3

Indice

Altri manuali SEW-Eurodrive Motore

SEW-Eurodrive

SEW-Eurodrive M1 N Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive MOVIMOT MMxD Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive R...7 Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DIB Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive Movimot MM05D Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DRC Manuale utente

SEW-Eurodrive

SEW-Eurodrive DRS 315 Manuale utente

SEW-Eurodrive

SEW-Eurodrive R...7 Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive MOVI-SWITCH-1E Guida per l'amministratore

SEW-Eurodrive

SEW-Eurodrive CM3C63 Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DRN71M4 Manuale utente

SEW-Eurodrive

SEW-Eurodrive SLC Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive MOVIMOT MM..D Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DFS Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DR2..71/BE Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DR Series Istruzioni operative

SEW-Eurodrive

SEW-Eurodrive DR Series Istruzioni operative

SEW-Eurodrive

SEW-Eurodrive CMP40 Manuale utente

SEW-Eurodrive

SEW-Eurodrive EDR71 Manuale utente

SEW-Eurodrive

SEW-Eurodrive MC Series Manuale utente

SEW-Eurodrive

SEW-Eurodrive DRN Series Istruzioni operative

SEW-Eurodrive

SEW-Eurodrive R...7 Series Istruzioni operative

SEW-Eurodrive

SEW-Eurodrive DR..71 Series Manuale di installazione e d'uso

SEW-Eurodrive

SEW-Eurodrive PSH CM2H Series Manuale utente

Manuali Motore popolari di altre marche

Rotax

Rotax 125 senior MAX evo Manuale utente

Kohler

Kohler K361 Manuale utente

MTD

MTD OHV Series Manuale utente

Kohler

Kohler COMMAND CH18-745 Manuale utente

Mercury

Mercury D4.2L D-Tronic Manuale utente

Selve

Selve SE Plus-RC Series Manuale utente

Perkins

Perkins 1206E-E66TA Manuale utente

Skov

Skov DA 174 Manuale

Rossi

Rossi TX11 Series Manuale utente

Siemens

Siemens SIMOTICS T-1FW3 Foglio di istruzioni

AL-KO

AL-KO PRO 350 Manuale utente

MTU

MTU 12 V 4000 Lx4 Manuale utente

Nanni

Nanni N3.30 Manuale di istruzioni

Nanni

Nanni N5.160 CR2 Manuale utente

KSB

KSB SuPreme Series Istruzioni per l'installazione

Hiwin

Hiwin EM1 Series Manuale utente

Rotax

Rotax 912 i series Istruzioni operative

Siemens

Siemens SIMOTICS XP 1MB1 Manuale utente